KX-NS1000 KX-NS1000 System Structure Rev.0.2 1

Introduction This document explains System Outline and Specification of the KX-NS1000, and is composed of the following chapters. Chapter 1 System Outline Chapter 2 Configuration Chapter 3 Supported Card /Terminal Chapter 4 System Capacity For further information about feature implementation and specifications, refer to the "Installation Manual“. We explains the general system outline and the specification of the KX -NS1000 with this document. 2

Table of Contents Chapter 1 System Outline 1-1. KX-NS1000 System Overview 1-2. System Connection Diagram 1-3. Unified Messaging Overview Chapter 2 Configuration 2-1. Cabinet Configuration 2-2. System configuration Chapter 3 Supported Card /Terminal 3-1. Terminal Compatibility Chapter 4 System Capacity 4-1. System Capacity 4-2. Terminal Capacity 4-3. Feature Capacity 4-4. Email Client Capacity

Chapter 1 System Overview

1-1. KX-NS1000 System Overview 1.Stand-alone System - A single NS1000 can be used as a stand-alone system. - To use the stand-alone system, you must install a DSP card on the PBX’s mother board, then install optional service cards into the physical slots and virtual slots. 2.Networked System A networked system can be realized by the following methods. - One-look - QSIG (required BRI /PRI card) - H.323 (required V-IPGW card) Master Unit ・・・ IP Network Slave Unit Up to 15 Units * For detail, refer to the Networking Chapter.

1-2. System Connection Diagram IP/Legacy Trunks IP/Legacy Terminals Remote PC Router IP-PT Private IP Network NS1000 SIP-Phone ITSP*1 Network IP-CS PS Unified Messaging *3 IP-Softphone, CA*2 Client PC - Analogue Trunk - BRI Trunk - PRI Trunk PSTN*4 PC PC CTI Server SLT / FAX External Sensor /External Relay Device - NS1000 is based on Linux OS. Doorphone & Door Opener BGM/Music On Hold (MOH) *1 ITSP: Internet Telephony Service Provider *2 Communication Assistant *3 Built-into Main unit *4 Public Switched Telephone Network Amplifier / Pager/Speaker

1-3. Unified Messaging Overview The Unified Messaging system is a new solution that adds unified messaging features such as voicemail, FAX and Email integration. The following features are available: Unified Messaging Feature Voice mail (TVM Features) Outlook add in Desktop Messaging Fax Server Automatic 2way Recording for Manager Feature Presence (Absent Messaging) Feature Unified Messaging feature is available with the Pre-installed SM card. Current New Storage memory card Built-in Main unit DPT I/F TVM TDE/NCP NS1000

Chapter 2 Configuration

2-1. Cabinet Configuration Component location The NS1000 (2U size) can be fitted to a 19-inch rack. (Depth is same as NCP Series) Dimensions: 430mm (Width) × 88mm (Height) × 340mm (Depth) Weight (when fully mounted): Under 4.5kg Front Side LED indicators MOH/EPG ports DPH Port (Option) Legacy Slot (Option) System mode SW USB port IP ports Back Side AC SW GROUND Serial port FAN AC cord clamp AC IN

2-2. System Configuration (1) New Innovative system architecture Provides the same level of PBX call control functionality as TDE/NCP system MPR Ver.4. NCP/TDE NS1000 PBX Call Control Features System Administration PBX Call Control Features System Administration + Networking Middleware - SIP protocol stack - Networking utilities - TCP /IP protocol stack (IPv4) Middleware - SIP protocol stack - Enhanced Panasonic-SIP - 従来のNCP/TDEとNS1000は、同一レベルのPBX Call Control Featuresに なってます。　　 OS (ｉTRON) OS (Linux) - Networking Utilities * - TCP /IP protocol stack (IPv4) CPU: SH-4 , 400MHz CPU: C1000 , 650MHz : NEW 10

2-2. System Configuration (2) System Options DSP cards*1 DSP-S DSP-M DSP-L *1 Each NS1000 (Master or Slave) must be fitted with a DSP card. Storage Memory*2 SM-S (Max 200hrs Rec) SM-M (Max 450hrs Rec) SM-L (Max 1000hrs Rec) Internal Mother board Option cards FAX DPH 1 External Line cards LCOT2+SLC2 BRI4+SLC2 PRI30+SLC2 *2 The NS1000 has Storage Memory Pre-installed (SM-B), and by default allows 2 UM channels and 2 hours recording time. (Expandable to 24ch / 15hrs by Activation Key.)

2-2. System Configuration (3) Interface Cards (Line and Doorphone) 4 types of Legacy Line cards are available for NS1000. 1 type of Doorphone interface card is also available for NS1000. [Line Card ] [DPH1 Card ] BRI4+SLC2 Card LCOT2+SLC2 Card PRI30+SLC2 Card NS1000 has 1 Free Slot for “Line card” and 1 Free Slot for “DPH1 card”.

2-2. System Configuration (4) Interface Cards – Free Slot (Description) Part Number Image Description KX-NS0180 SLC2 -LCOT2 Line Card 2 port Analogue Trunk with Caller ID (FSK/DTMF/Visual) Reverse supported, PAY Tone not supported 1 PFT Port 2 SLT Ports with Caller ID (FSK) No MSG Lamp or CPC Sending control KX-NS0280 SLC2 - BRI4 Line Card 4 ISDN Basic Rate interface ports. (EURO-ISDN/ETSI Compliant) KX-NS0290CE SLC2 -PRI30 Line Card 1 ISDN Primary Rate interface ports. (30B ch) KX-NS0161 -Doorphone Card 1 Doorphone, 1 Door Opener and 1 External Sensor port (Relay Current Limit: 24 V DC/30 V AC, 1 A max) OFF HOOK detection supported Doorphone connected detection supported

2-2. System Configuration (5) Optional Cards - Internal (Description) Part Number Image Description KX-NS0106 - FAX Card 1 channel Fax Server No additional A/K is necessary for FAX Server functionality – installing the FAX card automatically enables FAX Server Capability.

2-2. System Configuration (6) DSP Cards (Description) Digital Signal Processor (DSP) Cards support VoIP calls, Conferencing, UM and DISA/OGM features on the NS1000 system. Up to Two DSP Cards can be fitted to each NS1000 unit, increasing the available DSP resource. At least 1 DSP Card must be fitted to each NS1000 so that the unit can operate. There are 3 types of DSP card, each with different levels of DSP resource. The more resource available, the more simultaneous features / calls can be maintained. Model Type Resource Power IP Addresses KX-NS0110 DSP-S 61 1 KX-NS0111 DSP-M 125 KX-NS0112 DSP-L 252 2

2-2. System Configuration (7) Storage Memory Cards (SM) (Description) The NS1000 unit comes pre-installed with 2ch UM and 2hrs of Voice Mail recording capability. This can be increased to 15hrs by installing the KX-NSU001 A/K. The system VM recording capacity can be increased further by installing one of the optional SM cards. Model Type Max Recording Time (Hrs) KX-NS0135 SM-S 200 KX-NS0136 SM-M 450 KX-NS0137 SM-L 1000

2-2. System Configuration (8) Virtual Cards The NS1000 uses ‘virtual’ cards to support a range of IP based Trunks, Extensions, DECT Cell Stations and UM features. Virtual cards features can be activated with the appropriate activation key. Virtual Cards are configured via the Web-Based Maintenance Console. Virtual Card type Virtual Slot V-SIPGW16 V-SIPEXT32 V-IPCS4 V-IPUM12 V-IPGW16 V-IPEXT32 V-UTEXT32 Ethernet Other PBX IP Telephony Service IP-CS IP-PT SIP-MLT/SLT 17

2-2. System Configuration (9) Virtual Cards (Specification) Virtual Card Type Description Virtual 16-Channel VoIP Gateway Card (V-IPGW16) Virtual Card for 16-channel H.323 trunk. Compliant with VoIP H.323 V.5 protocol, and ITU-T G.729A and G.711 codec methods. Also supports T.38 protocol. Virtual 16-Channel SIP Trunk Card (V-SIPGW16) Virtual Card for 16-channel SIP trunk. Compliant with RFC 3261, 3262, 3264, 3311, 3581, 3960 and 4028 protocols, and ITU-T G.729A and G.711 codec methods. Also supports T.38 protocol. Virtual 32-Channel VoIP Extension Card (V-IPEXT32) Virtual Card for 32 IP-PTs (KX-NT300 series and KX-NT265 [software version 2.00 or later only]). Compliant with Panasonic proprietary protocol, and ITU-T G.729A, G.711 and G.722 codec methods. Virtual 32-Channel SIP Extension Card (V-SIPEXT32) Virtual Card for 32 third party SIP phones. Compliant with RFC 3261, 3264, 3310, 2327 and 4028 protocols, and ITU-T G. 729A, G.711 and G.722 codec methods. Virtual UT Extension Card (V-UTEXT32) Virtual Card for 32 KX-UT series SIP phones. Compliant with RFC 2327, 3261, 3264, 3310, 3515, 4028 and 4235 protocols, and ITU-T G.729A, G.711 and G.722 codec methods. Also supports WSD, CWMP and HTTP. Virtual 4 IP Cell Station Interface Card (V-IPCS4) Virtual Card for 4 IP-CSs. Compliant with ITU-T G.729A and G.711 codec methods.

2-2. System Configuration (10) Activation Keys (A/K) Activation Keys are required to activate the following features: IP Trunk channel(H.323/SIP) IP Telephone / Terminal capacity Number of IP Telephones /Type of IP Telephones (IP softphone / IP-PTs / SIP Phones (UT series) / Other SIP Phones / IP Conferencing Phones) Networking Features (One-Look, QSIG) Unified Messaging Features (REC Time, 2-Way REC, Message Backup, UM Port capacity, UM/Email (IMAP + Voice / Fax messages) Mobile Phone Features CA related Feature (Thin Client, CSTA Mux, CA Pro, CA Supervisor, CA Console, CA Networking) CTI Interface (Allows use of Third Party CTI Application) Packages containing a combination of different A/K’s are also available to equip users with key UM and Mobility features easily.

2-2. System Configuration (11) Activation Keys (A/K) – Cont.. The NS1000 is equipped with Preinstalled Permanent Activation Keys Type Feature IP-PT License 8 IP PT (Used for NT or UT series PT) UM License 2ch UM CA Basic-Express 1022 Users These A/Ks exist within the PBX hardware and cannot be deleted and will not expire.

2-2. System Configuration (12) Activation Keys (A/K) – Cont.. In addition to the pre-installed permanent A/Ks, there is the option to activate ‘trial’ A/Ks which are valid for 60 days. These trial A/Ks will expire 60 days after activation. Trail A/Ks cannot be re-activated by initializing the PBX system. Trial A/Ks (60 day expiry from activation) Activation Key Type Supported Mailboxes / Extensions / Features One-Look Network - Two-Way REC Control Message Backup UM / Email Users 128 Mailboxes Two-Way REC Users 30 Two-Way REC / Two-Way Transfer Users Mobile Users 30 Cellular Phone Users CTI Interface CA Pro 128 CA Pro User CA Supervisor 1 CA Supervisor User CA Console 1 CA Console User CA Thin Client CSTA Multiplexer

Supported Terminals Chapter 3 The chapter3 is Supported Card / Terminal.

3-1. Terminal Compatibility (1) New Range - SIP Telephone (UT Series) Terminal Type Compatible with NS1000 v1.0 SIP-MLT UT133 YES UT136 SIP-SLT*1 UT113 UT123 *1 UT113 : No backlit / UT123 : Backlit 23

3-1. Terminal Compatibility (2) Telephone Terminals Terminal Type Compatible with NS1000 v1.0 KX-NT3xx Series (IP-PT) YES KX-NT400 (IP-PT) NO KX-NT7xx Series (IP-Conference Phone) KXNCS81xx (IP-Softphone) 3rd Party SIP Phones KX-DT3xx Series (New Digital PTs) KX-T7xxx Series (Old Digital/Analogue PTs) DSS Consoles (KX-T7640 Series etc) SLTs (KX-7710 etc) KX-NT265 IP-PT (V2.x) KX-TCA155/255/256/355/356/TD7590/WT115 (Portable Stations) KX-T30800 Series PTs and DSS Consoles KX-T61600 Series PTs and DSS Consoles KX-T123200 Series PTs and DSS Consoles KX-TD7500 DECT Portable Station KX-NT265 IP-PT (V1.x) KX-NT136 IP-PT For compatible options (e.g., Add-on Key Module, USB Module, Headset), refer to the telephone’s manual. 24

3-1. Terminal Compatibility (3) Other Terminals Terminal Type Compatible with NS1000 v1.0 TDA0141CE 2ch CS (DPT IF) NO TDA0142CE 4ch CS (CSIF) TDA0158CE 8ch CS (DPT IF) NCP0158CE 8ch CS (IP IF) YES A228 S/M-type battery backup cable A229 L-type battery backup cable A258 Blank Slot cover T30865 Doorphone T7765 Doorphone 25

Chapter 4 System Capacity

4-1. System Capacity (1) Type and Maximum Number of Slots The NS1000 supports the following type and number of slots. Slot Type Maximum Number Stand-alone System One-look Network FAX Card Slot 1 16 Storage Memory (SM) Slot DSP Card Slot 2 32 Free Slot Doorphone Slot Virtual Slot 20 Virtual Trunk Card Virtual Extension Card Virtual IP-CS Card

4-1. System Capacity (2) Maximum Optional Service Cards (1) The following number of cards can be installed in the Physical Slots of the PBX. Card Type Maximum Number Stand-alone System One-look Network Physical Card 2 32 Line Card Slot 1 16 LCOT2+SLC2 BRI4+SLC2 PRI30+SLC2 Doorphone Slot DPH1 Note Any card that exceeds the capacity of the PBX will be ignored. When the PBX starts up with an invalid configuration, some cards will be ignored.

4-1. System Capacity (3) Maximum Optional Service Cards (2) The following number of cards can be installed in the Physical Slots of the PBX. Card Type Maximum Number Stand-alone System One-look Network DSP Card Slot 2 32 DSP-S 1 16 DSP-M DSP-L FAX Slot FAX Storage Memory Card Slot 1 16 SM-S SM-M SM-L Note Any card that exceeds the capacity of the PBX will be ignored. When the PBX starts up with an invalid configuration, some cards will be ignored.

4-1. System Capacity (4) Maximum Optional Service Cards (3) The following number of cards can be installed in the Virtual Slots of the PBX. Card Type Maximum Number Stand-alone System One-look Network Virtual Trunk Card 16 V-IPGW16 3 6 V-SIPGW16 Virtual Extension Card 20 32 V-IPEXT32 4 V-SIPEXT32 V-UTEXT32 V-IPCS4 Virtual Unified Messaging Card 2 V-IPUM12

4-1. System Capacity (5) Maximum Trunks and Extensions The PBX supports the following number of trunks and extensions. Type Stand-alone System One-look Network Total Number of Trunks 256 600 Trunk (Virtual Trunk Card) H.323 Trunks 48 96 SIP Trunks Trunk (Physical Trunk Card) 30 480 Total Number of Extensions 640 1000*1 Extension (Virtual Extension Card) 1000 IP-PT and IP Softphone 128 SIP Extension Extension (Physical Extension Card) 2 32 *1 The maximum number of extension ports is 640 per PBX, and the maximum number of Unified Messaging ports is 24 per PBX. When 24 ports for Unified Messaging are fully activated on the Master unit, the maximum number of extension ports will be less than 640. One Unified Messaging port is equal to 10 extension ports. Therefore, when all Unified Messaging ports are activated, only up to 420 extensions are available. (The 2 Built-in UM ports are not counted in this calculation). This condition does not apply for Slave units or Stand-Alone units.

4-2. Terminal Capacity Maximum Terminal Equipment The following shows the number of each terminal equipment type supported by the PBX. Terminal Type Stand-alone System One-look Network Telephone 640 1000 SLT 2 32 IP-PT*1 128 SIP Phone Wireless IP-CS (8-channel) 64 PS 512 Unified Messaging (Channels) 24 384 (24x16) Doorphone 1 16 Door Opener External Sensor *1 KX-NT300 series, and KX-NT265(v2.0).

2-Way Recording (Users) 4-3. Feature Capacity Maximum Feature capacity The following shows the maximum number of each feature supported by the PBX. Type Stand-alone System One-Look Network UM Mailbox 1024 16384 2-Way Recording (Users) 640 1000 Mobile Users 1152 CA Client Login Mode Server-less Server Basic - Express 240 1022 Pro Operator Console 128 Supervisor 4 NB: Total number of Login in Server Mode is 1022

4-4. Email Client Capacity Outlook Integration with built-in Unified Messaging The maximum number of IMAP clients using Outlook is 24 users per unit. (Reason: Outlook keeps the IMAP session open, even though then user is idle.) Type of mailer Outlook (+Tool Bar)*1 Other*2 # of UM Email Client 24 640 *1) This limitation is not applied if the user can use Outlook in “Offline” mode. *2) Email which releases IMAP session when idle, such as Thunderbird, Lotus Notes etc. Integration with POP No limitation for users who receive voice data with an email attachment.

THE END