1. Legacy-GW Features
Rev Jan., 2013

2. Over view
Chapter 1: Product Overview . 2

3. Over view 1.Use NCP/TDE（TDA）as a legacy GW by stacking connection
with NS1000.
2.NCP/TDE(TDA) connect with NS by stacking card working
as part of One-look network.

4. Over view
Introduce new card ; STACK-M (for NS), STACK-S (1 for NCP/ 1 for TDE)
Site #1
STACK-M card
Slave Units
NS1000 as stacking Master Unit
Master for
One-look
Site #2
Site #3
Stacking Slave
NCP500
NCP1000
LAN
Stacking Slave
Stacking Slave
Site #4 　：
Stacking Slave
STACK-S card
Proprietary cable for stacking connection The length of the cable：2M (Dedicate cable for these Stacking card) 4

5. Over view New card Symbol Model Name Description Remark STACK-M
KX-NS0130
Stacking Master Card
- Interface card for Legacy-GW
- Proprietary Interface x 2 ports
Symbol
Model
Name
Description
Remark
STACK-S
(NCP)
KX-NS0131
Stacking EXP Card for NCP
Legacy-GW Control Unit for NCP
with Stacking Cable
(TDE/TDA)
KX-NS0132
Stacking EXP Card for TDE/TDA
Legacy-GW Control Unit for TDE/TDA

6. Condition
Chapter 1: Product Overview .

7. Condition 1 1.MPR of NCP has to be removed to install Stack-S card.
This means Virtual card on NCP
is not supported.
All of IP terminal has to connect to
NS1000.
2.Type of GW has to be same for
each NS1000.
　Category1: NCP500 /NCP1000
　 Category2: TDE100/200, TDA100/200
Category3: TDE600/620, TDA600/620
3.Max 2 GW for each NS. Max 8 for
entire One-look network.
4.TDA15/30/50/100D is not
supported.
5. AK is not required to use Legacy GW.
STACK-M card
Stacking Slave #1
Stacking Slave #2
*If the type of cabinet is mixed then
2nd one will not be worked.
STACK-S card 7

8. Condition 2
In case of TDE600 each cabinet count as 1 GW and connection to NS has to be done
by Stack-S card.
Bus card in TDE600 and TDE620 has to be removed.
NS1000
NS1000
NS1000
TDE620
TDE620
TDE600
TDE600
TDE620
TDE600 OR OR 8

9. Which Optional card can not be used at Legacy GW?
Condition 3
Which Optional card can not be used at Legacy GW?
Symbol
Model
Description
RMT
TDA0196
Analogue Modem for Remote Maintenance
MEC
TDA0105/
TDE0105
Memory Expansion Card
DSP4
NCP1104
VoIP channel card 4ch
DSP16
TDE0110
VoIP channel card 16ch
DSP64
TDE0111
VoIP channel card 64ch
CTI-LINK
TDA0410
CTI Link Card
IP-EXT16
TDA0470
16-Channnel VoIP Extension Card
IP-GW4E
TDA0484
4-Channnel VoIP Gateway Card
IP-GW16
TDA0490
16-Channnel VoIP Gateway Card
IP GW4
TDA0480
4 Channel VoIP Gateway Card
MSG4
TDA0191
4-Channel Message Card
ESVM2
TDA0192
2-Channel Simplified Voice Message Card
ESVM4
TDA0194
4-Channel Simplified Voice Message Card
CLCOT8
TDA1180
8-Port Analogue Trunk Base Card w/ Caller ID
CLCOT8E
TDA1186
8-Port Analogue Trunk Daughter Card w/ Caller ID
MCSLC24
TDA1178
24-Port Single Line Telephone Card
MCSLC16
TDA1176
16-Port Single Line Telephone Card
Basically
Optional card
1)on TDE/NCP MPR
2)Support by V5 or later
3) IP-GW, IP-EXT
4) MSG
are not supported. 9

10. Condition 4 How many CO can be installed in each Legacy GW?
Stand-alone
Stacking system
One Look
Networking
1NCP500
1NCP1000
1TDE/TDA100
1TDE/TDA 200
1TDE/TDA 600
2NCP500
2NCP1000
2TDE/TDA 100
2TDE/TDA 200
2TDE/TDA 600
Trunk(ch)
256
600 IP
SIP
H.323 48 96
Legacy 30
64/64/120/128/160
128/128/240/256/256
LCOT 2
12/16/96/128/160
24/32/192/256/256
BRI 8
PRI23 23
46/46/92/92/115
92/92/184/184/230
PRI30
60/60/120/120/150
120/120/240/240/256 T1
48/48/96/96/120
96/96/192/192/240 E1 10

11. Condition 5 How many EXT can be installed in each Legacy GW?
Stand-alone
Stacking system
One Look
Networking
1NCP
1TDE/TDA100
1TDE/TDA 200
1TDE/TDA 600
2NCP
2TDE/TDA 100
2TDE/TDA 200
2TDE/TDA 600
Extension(ch)
640
1000 IP
IP-PT
256
SIP
SIP Phone
KX-UT series
S-PS(SIP based DECT)
255
Legacy *1 2
44/160/256/304
88/320/512/608
SLT
36/96/128/240
72/192/256/480
DPT
40/128/256/256
80/256/512/512
Legacy DECT PS 512 has not been changed. 11

12. Condition 6 How many other devices can be installed in each Legacy GW?
Stand-alone
Stacking system
One Look
Networking
1NCP
1TDE/TDA100
1TDE/TDA 200
1TDE/TDA 600
2NCP
2TDE/TDA 100
2TDE/TDA 200
2TDE/TDA 600
CS (pcs) 64
128
DPT-CS (2ch)
11/32/32/32
22/64/64/64
DPT-CS (8ch)
5/16/16/16
10/32/32/32
IP-CS
64 *2
128 *2
SIP-CS
64 *3
128 *3
PS(DECT)(pcs)
512 VM
Built-in UM (ch) 24
24ch x16
TVA/TVM (ch)
48 (24ch x2)
24ch x8
*2 The maximum number of Air Sync Groups is 16. An Air Sync Group can contain up to 16 IP-CSs.
*3 The maximum number of Air Sync Groups is 8. An Air Sync Group can contain up to 32 SIP-CSs.

13. Condition 7 AK on NCP/TDE can’t be transferred to NS MPR.
In case of TDA100/200 and TDE100/200
OPB3 card with ECHO16 must be installed in only SLOT1. - Other than OPB3 card allows to install in any SLOT. - OPB3 card with sub-card except for ECHO16 allows installing in any SLOT.
HGT100, NT400 can’t be connected to NS MPR. 13

14. How to work?

15. How to work? Installation
Both Stack-M and Stack-S card is non hot swappable.
Each cabinet can be power on without any order.
Initial Legacy-GW installation, all card will be initialized.
The optional service cards is hot swappable.
TVM can be installed as VM system for entire One-look.
CS can be installed at both NS(NCP0158) and Legacy-GW
(TDA0141/142/155/156/158). PS can Hand over between
these CS to CS(NCP0158, TDA0141/142/155/156/158).

16. How to work?
Wireless
Hand over between NS to Legacy GW and Legacy GW to
Legacy GW is available.
LAN
IP-CS
IP-CS(NCP0158) CS
CS(TDA0141/142/155/156/158) PS CS CS
If Legacy CS and IPCS are mixed then all CS must be assign under Air sync group 1.

17. How to work? Start up LED Status “Stack-M” LED
Green On : Normal working condition
Off: Error( Not Working)
“Stack-S” LED
Green On : INS
Red On : Fault
Red Flash: OUS
Legacy GW
“RUN” LED
Green Off :Power off
On : Running as GW
Slow Flash: While start up
“ALARM” LED
Red Off : No present error
On : Present Error

18. How to work? Maintenance
All below service for Legacy-GW is supported through NS1000 cabinet.
Programming
Firmware update
Error log, Syslog
SNMP information
SMDR

19. Programming

20. Programming Programming at NS1000
Button to switch Physical-Virtual-LegacyGW1-LegacyGW2
Stack S connect to “1” on
Stack M consider as “GW1”
Each Optional Card can be selected and installed.

21. Programming Programming at NS1000
LPR Software :Software can be download through NS1000
LPR Software name same as existing models
LPR Software for STACK-S card “PSTKS” is new!

22. Programming Programming at NS1000
Programming items related to Legacy GW support.
Related to VM.
Related to DSS.
Port Property

23. Appendix

24. Appendix
Supported optional card

25. Appendix
Supported optional card

26. Appendix
Supported optional card

27. END

28. Modification 20120827-01 LegacyGW_Rev1_27Aug2012Mar.ppt - 1st release
LegacyGW_Rev1_1_5Sep2012Mar.ppt
- Edit slide #11 revise number of legacy EXT and DPT.
- Add slide #12
LegacyGW_Rev1_2_31Oct2012Mar.ppt
- Add comment for slide #7 “No AK required”
- Add additional sample for slide #8
- Add comment for slide #9 “Basic idea”
- Add comment for #13 about HGT100 and NT400
- Add remark for #16
LegacyGW_Rev1_3_8Nov2012Mar.ppt
- correct slide # twice to and
LegacyGW_Rev1_4_24Jan2013Mar.ppt
- correct slide #10 BRI and LCOT capacity for NCP500 as Legacy GW