VI. CLX-6240FX & CLX-6200FX series Firmware VI. CLX-6240FX & CLX-6200FX series Firmware

Revision History V0.1 : : Initial Release – Joong Mok Lee Revision : to Now - Won Young Chi

Overview - I Model –CLX-6200ND : DADF, HDD option, wireless LAN option –CLX-6200FX : ADF, FAX –CLX-6210FX : DADF, FAX, HDD option, wireless LAN option –CLX-6240FX : DADF, FAX, HDD, wireless LAN option Print method –Single-pass printing (Y->M->C->K) Printing speed –CLX-62x0  20/20 ppm (Color/Mono) –CLX-6240  20/20 ppm (Color/Mono) Resolution in printing (PC printing) –Best mode 1200 x 1200 dpi –Normal mode 1200 x 600 dpi –Draft mode 600 x 600 dpi Resolution in printing (Copy) –Default 600 x 600 dpi –Platen photo 1200 x 1200 dpi Duplex mode support

Overview - II Supported I/O port –USB, Network CRUM –C/M/Y/K Toner, PTB Memory size (default) –CLX-62x0 : 128MBytes –CLX-6240 : 256MBytes Panel –2- line LCD panel support –Ten key, speed dial support –STOP, Start (Color/Mono) Key

Overview - III CPU (CLX-62x0/CLX-6240) –Type : CHORUS3/SPGPXm (ARM 920EJ /PMC 7065) –Speed : 300MHz/533MHz –Bus speed : 120MHz/ 120MHz –One chip solution (HPVC, I/O, JBIG, network …) Real-Time OS (CLX-62x0/CLX-6240) –pSOS (V2.5) / VxWorks Network configuration –Embedded Network

ROM Image ROM image ROM release –Boot image –ROM image (except boot image) CLX-62x0CLX-6240 ROM Size16.0M bytes Boot256K bytes Kernel10M bytes12M bytes Emulation6M bytes Network8M bytes10M bytes Demo Page2M bytes

F/W Upgrade USB and Network port are used to F/W upgrade Network applications (SWAS, SWS) can be used for network port upgrade Notice : In special mode upgrade, kernel waste header information for CLX-62x0/CLX You have to check F/W ROM file with MFP set (This mode is ONLY service mode, not user mode)

F/W Upgrade using USB Port – Make sure connecting Printer to the computer with a USB cable – Upgrade in Ready mode Send ROM image file via USB cable in Ready mode – Upgrade in Special mode Power ON with pressing ‘STOP key’ two times Change LCD message ‘Wait Image’ Send ROM image file via USB cable F/W Upgrade – using button

F/W Upgrade – using SWS F/W upgrade using SWS(SyncThru Web Service) –Home -> Maintenance -> Firmware Upgrade 1 2 3

F/W Upgrade – using SWAS 1. F/W upgrade using SWAS(SyncThru Web Admin Service) –Home  Maintenance

F/W Upgrade - using SWAS 2. F/W upgrade using SWAS(SyncThru Web Admin Service) –Firmware Upgrade  Upgrade (check device using IP address) 1 2 3

F/W Upgrade - using SWAS 2. F/W upgrade using SWAS(SyncThru Web Admin Service) –Maintenance -> Firmware upload (register firmware) 1 2 3

F/W Upgrade - using SWAS 2. F/W upgrade using SWAS(SyncThru Web Admin Service) –Maintenance -> Firmware Upload (upload firmware)

F/W Upgrade - using SWAS 2. F/W upgrade using SWAS(SyncThru Web Admin Service) –Maintenance -> Firmware Upload (confirm uploaded firmware) 1 2 3

F/W Upgrade - VI 2. F/W upgrade using SWAS(SyncThru Web Admin Service) –Maintenance -> Firmware Upgrade -> Upgrade (choose firmware) 1 2 3

F/W Upgrade - VI 2. F/W upgrade using SWAS(SyncThru Web Admin Service) –Maintenance -> Firmware Upgrade -> Upgrade (choose firmware) 1 2 3

F/W Upgrade - using SWAS 2. F/W upgrade using SWAS(SyncThru Web Admin Service) –Maintenance -> Firmware Upgrade -> Upgrade

F/W Upgrade - using SWAS 2. F/W upgrade using SWAS(SyncThru Web Admin Service) –Maintenance -> Firmware Upgrade -> Upgrade (Done) 1 2 3

Information print Demo page –Press OK Key for 2sec –Blinking Green LED (status LED) System Configuration page –Menu  System Setup  report  configuration  ‘yes’ –Blinking Green LED (Status LED) Network Configuration page –Menu  System Setup  report  Network Info.  ‘yes’ –Menu  Network  Network Info.  ‘yes’ –Blinking Green LED (Status LED)

Total Page Count (Color/Mono) Page Count (C/M/Y/K) Fuser Life Toner Remains Percent (C/M/Y/K) Transfer Belt Life Tray1/Tray2 Roller Life MP Roller Life Model ID (C/M/Y/K/PTB) Serial No. (C/M/Y/K/PTB) Product Date (C/M/Y/K/PTB) Last Used Date First Installed Date ADF Scan Page Count Platen Scan Page Count Consumables Information (C/M/Y/K) Supplies Information

Status Monitor Display in Status Monitor window Consumables Life Errors –Toner Low –Toner empty –Replace Toner Cartridge –Replace transfer belt soon –Replace transfer belt –Replace fuser soon –Replace fuser –Replace imaging unit soon –Replace imaging unit –Replace Pickup (tray1/tray2) roller Need to replace those items when replace error is indicated

Consumable Unit Activity Toner Empty Status should be selected option as below: - Color : Stop, Continue, Mono Only - Mono : Stop, Continue *Stop  all printing is not allowed. *Continue  all printing is allowed until toner cartridge is exhausted. *Mono Only  color printing data is wasted. Mono printing only allowed. Invalid/Install Toner Status - Color/Mono/PTB : all printing operation is not allowed. Exhausted Toner Status (After Empty Status) -Color/Mono : all printing operation is not allowed.

Lily (CLX-62x0) Part. II Engine F/W

EDC Mode Method to enter Power – On the printer, and wait until the “READY” message appearing on LCD Panel. Push button like next time “Menu -> Stop -> Left arrow -> Back -> OK -> Right arrow” “COMPONEMT TEST Press Menu Key” ① ② ③ ④ ⑤ ⑥

Keys KeyDescription MenuMove to the top menu Left ArrowMove test item OKStart testing or select Sub-item Right arrowMove test item BackMove upper menu StopStop testing

EDC Menu –0. Cover Status ItemDescription Top CoverWhen a top cover opened, “Open” message display LCD. If the top cover closed, ”Closed” message display LCD Tray2 DoorWhen a tray2 door opened, “Open” message display LCD. If the tray2 door closed, ”Closed” message display LCD

Cont. –1. Sensor Status ItemDescription Regi. SensorIf actuator is checked by sensor, "Without Paper" message will be displayed. if not, "With Paper" will be. Exit SensorIf actuator is checked by sensor, "Without Paper" message will be displayed. if not, "With Paper" will be. MP EmptyIf paper exists in the MP tray, "With Paper" will be displayed. If not, "Without Paper" will be. T1 Paper EmptyIf paper exists in the 1 st tray, "With Paper" will be displayed. If not, "Without Paper" will be. T2 Paper EmptyIf paper exists in the 2 nd tray, "With Paper" will be displayed. If not, "Without Paper" will be. Rev. Swing SensorIf actuator is checked by sensor, "Without Paper" message will be displayed. if not, "With Paper" will be. Rev. Exit SensorIf actuator is checked by sensor, "Without Paper" message will be displayed. if not, "With Paper" will be.

Cont. –2. Motor Test ItemDescription Main Mtr Nor.If “OK” key is pushed after “ON” displayed, motor will be run. Main motor will auto - stop after 5 seconds and ”OFF” message will be displayed. Dev Mtr Nor.If “OK” key is pushed after “ON” displayed, motor will be run. Dev motor will auto - stop after 5 seconds and ”OFF” message will be displayed. Fuser Mtr Fwd.If “OK” key is pushed after “ON” displayed, motor will be run forward. Fuser motor will auto - stop after 5 seconds and ”OFF” message will be displayed. Fuser Mtr Bwd.If “OK” key is pushed after “ON” displayed, motor will be run Backward. Fuser motor will auto - stop after 5 seconds and ”OFF” message will be displayed. T2 Feed MotorIf “OK” key is pushed after “ON” displayed, motor will be run. T2 feed motor will auto - stop after 5 seconds and ”OFF” message will be displayed. Reverse MtrIf “OK” key is pushed after “ON” displayed, motor will be run. Dev motor will auto - stop after 5 seconds and ”OFF” message will be displayed.

Cont. –3. Fan Test ItemDescription Fuser FanIf “OK” key is pushed after “ON” displayed, fan will be run. Fuser fan will auto - stop after 5 seconds and ”OFF” message will be displayed. SMPS FanIf “OK” key is pushed after “ON” displayed, fan will be run. SMPS fan will auto - stop after 5 seconds and ”OFF” message will be displayed. LSU FanIf “OK” key is pushed after “ON” displayed, fan will be run. LSU fan will auto - stop after 5 seconds and ”OFF” message will be displayed. Reverse FanIf “OK” key is pushed after “ON” displayed, fan will be run. Reverse fan will auto - stop after 5 seconds and ”OFF” message will be displayed.

Cont. –4. Clutch/Sol. ItemDescription T1 P - up ClutchWhen “OK” key is pushed after ”ON” message displayed, clutch turn on. pick up clutch will be turn off after 5 seconds and ”OFF” message will be displayed. T2 P - up ClutchWhen “OK” key is pushed after ”ON” message displayed, clutch turn on. pick up clutch will be turn off after 5 seconds and ”OFF” message will be displayed. (when SCF is not installed, “not installed” message will be displayed ) MP P - up ClutchWhen “OK” key is pushed after ”ON” message displayed, clutch turn on. pick up clutch will be turn off after 5 seconds and ”OFF” message will be displayed. K Dev. ClutchWhen “OK” key is pushed after ”ON” message displayed, clutch turn on. K - clutch will be turn off after 5 seconds and ”OFF” message will be displayed.

Cont. –5. Fuser Ctrl ItemDescription Fuser1 Control Fuser 1 on and off. “ON” is selected, fuser will be active and display the fuser temperature [XXX] but “OFF” is selected, fuser will be stop and [0] display Fuser2 ControlFuser 2 on and off. “ON” is selected, fuser will be active and display the fuser temperature [XXX] but “OFF” is selected, fuser will be stop and [0] display Fuser Temp.AFuser1 temperature displayed on LCD (example: [251] ) Fuser Temp.BFuser2 temperature displayed on LCD (example: [251] )

Cont. –6. LSU Control ItemDescription LD Power YWhen “OK” key is pushed after ”ON” message displayed, ”OFF” message will be displayed after 5 seconds LD Power MWhen “OK” key is pushed after ”ON” message displayed, ”OFF” message will be displayed after 5 seconds LD Power CWhen “OK” key is pushed after ”ON” message displayed, ”OFF” message will be displayed after 5 seconds LD Power KWhen “OK” key is pushed after ”ON” message displayed, ”OFF” message will be displayed after 5 seconds LSU MotorIf “OK” key is pushed after “ON” displayed, motor will be run. LSU motor will auto - stop after 5 seconds and ”OFF” message will be displayed.

Cont. –7. DEV Control ItemDescription ChargerIf “OK” key is pushed after “ON” displayed, Charger voltage will be turned on. Dev DC YIf “OK” key is pushed after “ON” displayed, Dev DC Y will be turned on. Dev DC MIf “OK” key is pushed after “ON” displayed, Dev DC M will be turned on. Dev DC CIf “OK” key is pushed after “ON” displayed, Dev DC C will be turned on. Dev DC KIf “OK” key is pushed after “ON” displayed, Dev DC K will be turned on. Dev AC YIf “OK” key is pushed after “ON” displayed, Dev AC Y will be turned on. Dev AC MIf “OK” key is pushed after “ON” displayed, Dev AC M will be turned on. Dev AC CIf “OK” key is pushed after “ON” displayed, Dev AC C will be turned on. Dev AC KIf “OK” key is pushed after “ON” displayed, Dev AC K will be turned on. Dev TR YIf “OK” key is pushed after “ON” displayed, Dev TR Y will be turned on. Dev TR MIf “OK” key is pushed after “ON” displayed, Dev TR M will be turned on. Dev TR CIf “OK” key is pushed after “ON” displayed, Dev TR C will be turned on. Dev TR KIf “OK” key is pushed after “ON” displayed, Dev TR K will be turned on. P ChargerIf “OK” key is pushed after “ON” displayed, Paper Charger will be turned on.

Cont. –8. Reset Param ItemDescription Reset Color Reg“YES” is Selected, reset color registration starts. ( Take care of this menu because all color regi. data is initialized.)

Cont. –9. PrintTest ItemDescription Pattern Print“YES” is Selected, pattern printing starts.

Error list and recovery Operating Error –Paper Jam MP(Tray1, Tray2) Paper Jam0 –When feed sensor is not checked in limit-time after Pick- up –Right Cover Open /Close (check Feed Sensor and Pick-up solenoid) Paper Jam1 Open/Close Door – When exit sensor is not checked in limit-time after Feed - In –Right Cover Open-> remove the paper-> cover close (check Feed Sensor, Exit sensor and fuser motor) Paper Jam2 Check Inside –When exit sensor is not checked in limit-time after Exit-In –Right Cover Open-> remove the paper-> cover close (check the exit sensor) Duplex Jam0 Check Inside –When Feed sensor is not checked in limit-time after Exit-Out Reverse Jam0 Check Inside –When rev. Swing sensor is not checked in limit-time after Exit-In Reverse Jam1 Check Inside –When rev. Exit sensor is not checked in limit-time after Swing-Out

Cont. –Cover Error Cover Open : Install Transfer Belt message is toggled. –When right cover is opened or PTB (Paper Transfer Belt) is not installed –Check that PTB is installed –Check Right-cover switch, and PTB connector –Cassette Out Error Tray1(Tray2) Cassette Out –When Tray1- Cassette is out. –When tray is dedicated Tray2 in printer – driver and Tray2- Cassette is out. –Paper Empty / Paper Mismatch MP(Tray1, Tray2) Paper Empty –When dedicated-tray is empty Load A4 In MP(Tray1, Tray2) –When paper dedicated in driver is different with paper in tray. –Push the ”Stop” key, and documents will be printed continuously

Cont. Service Call error – LSU Motor Error Cycle Power When lock signal of LSU motor is not checked Check LSU and Main board (check Connector) –OPC Motor Locked / Deve Motor Locked When lock signal of BLDC motor is not checked Check Motor and Main board (check Connector) – Fuser Error Low Heat Error Cycle Power – Fuser temperature is not reached at target temperature in limited time. Over Heat Error Cycle Power –When Fuser temperature is more than a over- heat temperature ADC Slope Error Cycle Power –Fusing Unit is not heated Thermistor Open/Short Cycle Power –Thermistor level is not normal Check Thermistor is not connected, Thermistor is dirty, thermostat is opened

Cont. –Outer (Inner) Temp. Error Cycle Power Temp. Sensor- level is not normal –When color Regi. is not corrected First, Check Toner-Density Second, Check scratch of PTB.

Cont. Consumables –Install Cyan (Magenta, Yellow, Black) Toner –Install Transfer Belt When CRUM Interface is abnormal Extract Consumables from the Printer, and push consumables to the printer again. –Invalid Cyan (Magenta, Yellow, Black) Toner –Invalid Transfer Belt When CRUM Interface is abnormal Extract Consumables from the Printer, and push consumables to the printer again.

The end