1. KX-NS1000
KX-NS1000
System Structure Rev.0.2 1

2. Introduction
This document explains System Outline and Specification of the KX-NS1000, and is composed of the following chapters. Chapter 1 System Outline Chapter 2 Configuration Chapter 3 Supported Card /Terminal Chapter 4 System Capacity For further information about feature implementation and specifications, refer to the "Installation Manual“.
We explains the general system outline and the specification of the KX -NS1000 with this document. 2

3. Table of Contents
Chapter 1 System Outline 1-1. KX-NS1000 System Overview 1-2. System Connection Diagram 1-3. Unified Messaging Overview Chapter 2 Configuration 2-1. Cabinet Configuration 2-2. System configuration Chapter 3 Supported Card /Terminal 3-1. Terminal Compatibility Chapter 4 System Capacity 4-1. System Capacity 4-2. Terminal Capacity 4-3. Feature Capacity Client Capacity

4. Chapter 1
System Overview

5. 1-1. KX-NS1000 System Overview
1.Stand-alone System - A single NS1000 can be used as a stand-alone system. - To use the stand-alone system, you must install a DSP card on the PBX’s mother board, then install optional service cards into the physical slots and virtual slots. 2.Networked System A networked system can be realized by the following methods. - One-look - QSIG (required BRI /PRI card) - H.323 (required V-IPGW card)
Master Unit
・・・
IP Network
Slave Unit
Up to 15 Units
* For detail, refer to the Networking Chapter.

6. 1-2. System Connection Diagram
IP/Legacy Trunks
IP/Legacy Terminals
Remote PC
Router
IP-PT
Private IP Network
NS1000
SIP-Phone
ITSP*1 Network
IP-CS PS
Unified
Messaging *3
IP-Softphone, CA*2 Client PC
- Analogue Trunk
- BRI Trunk
- PRI Trunk
PSTN*4 PC PC
CTI Server
SLT / FAX
External Sensor
/External Relay Device
- NS1000 is based on Linux OS.
Doorphone & Door Opener
BGM/Music On Hold (MOH)
*1 ITSP: Internet Telephony Service Provider
*2 Communication Assistant
*3 Built-into Main unit
*4 Public Switched Telephone Network
Amplifier / Pager/Speaker

7. 1-3. Unified Messaging Overview
The Unified Messaging system is a new solution that adds unified messaging features such as voic , FAX and integration.
The following features are available:
Unified Messaging Feature
Voice mail (TVM Features)
Outlook add in Desktop Messaging
Fax Server
Automatic 2way Recording for Manager Feature
Presence (Absent Messaging) Feature
Unified Messaging feature is available with the Pre-installed SM card.
Current
New
Storage memory card
Built-in Main unit
DPT I/F
TVM
TDE/NCP
NS1000

8. Chapter 2
Configuration

9. 2-1. Cabinet Configuration
Component location
The NS1000 (2U size) can be fitted to a 19-inch rack. (Depth is same as NCP Series)
Dimensions: 430mm (Width) × 88mm (Height) × 340mm (Depth)
Weight (when fully mounted): Under 4.5kg
Front Side
LED indicators
MOH/EPG ports
DPH Port (Option)
Legacy Slot (Option)
System mode SW
USB port
IP ports
Back Side
AC SW
GROUND
Serial port
FAN
AC cord clamp
AC IN

10. 2-2. System Configuration (1)
New Innovative system architecture Provides the same level of PBX call control functionality as TDE/NCP system MPR Ver.4.
NCP/TDE
NS1000
PBX Call Control
Features
System
Administration
PBX Call Control
Features
System
Administration
+ Networking
Middleware
- SIP protocol stack
- Networking utilities
- TCP /IP protocol stack (IPv4)
Middleware
- SIP protocol stack
- Enhanced Panasonic-SIP
- 従来のNCP/TDEとNS1000は、同一レベルのPBX Call Control Featuresに
なってます。　　
OS (ｉTRON)
OS (Linux)
- Networking Utilities *
- TCP /IP protocol stack (IPv4)
CPU: SH-4 , 400MHz
CPU: C1000 , 650MHz
: NEW 10

11. 2-2. System Configuration (2)
System Options
DSP cards*1
DSP-S
DSP-M
DSP-L
*1 Each NS1000 (Master or Slave) must be fitted with a DSP card.
Storage Memory*2
SM-S (Max 200hrs Rec)
SM-M (Max 450hrs Rec)
SM-L (Max 1000hrs Rec)
Internal
Mother board
Option cards
FAX
DPH 1
External
Line cards
LCOT2+SLC2
BRI4+SLC2
PRI30+SLC2
*2 The NS1000 has Storage Memory Pre-installed (SM-B), and by default allows 2 UM channels and 2 hours recording time. (Expandable to 24ch / 15hrs by Activation Key.)

12. 2-2. System Configuration (3)
Interface Cards (Line and Doorphone) 4 types of Legacy Line cards are available for NS type of Doorphone interface card is also available for NS1000.
[Line Card ]
[DPH1 Card ]
BRI4+SLC2 Card
LCOT2+SLC2 Card
PRI30+SLC2 Card
NS1000 has 1 Free Slot for “Line card” and 1 Free Slot for “DPH1 card”.

13. 2-2. System Configuration (4)
Interface Cards – Free Slot (Description)
Part Number
Image
Description
KX-NS0180 SLC2 -LCOT2 Line Card
2 port Analogue Trunk with Caller ID (FSK/DTMF/Visual)
Reverse supported, PAY Tone not supported
1 PFT Port
2 SLT Ports with Caller ID (FSK)
No MSG Lamp or CPC Sending control
KX-NS0280 SLC2 - BRI4 Line Card
4 ISDN Basic Rate interface ports.
(EURO-ISDN/ETSI Compliant)
KX-NS0290CE SLC2 -PRI30 Line Card
1 ISDN Primary Rate interface ports. (30B ch)
KX-NS0161 -Doorphone Card
1 Doorphone, 1 Door Opener and 1 External Sensor port
(Relay Current Limit: 24 V DC/30 V AC, 1 A max)
OFF HOOK detection supported
Doorphone connected detection supported

14. 2-2. System Configuration (5)
Optional Cards - Internal (Description)
Part Number
Image
Description
KX-NS0106 -
FAX Card
1 channel Fax Server
No additional A/K is necessary for FAX Server functionality – installing the FAX card automatically enables FAX Server Capability.

15. 2-2. System Configuration (6)
DSP Cards (Description) Digital Signal Processor (DSP) Cards support VoIP calls, Conferencing, UM and DISA/OGM features on the NS1000 system.
Up to Two DSP Cards can be fitted to each NS1000 unit, increasing the available DSP resource.
At least 1 DSP Card must be fitted to each NS1000 so that the unit can operate.
There are 3 types of DSP card, each with different levels of DSP resource.
The more resource available, the more simultaneous features / calls can be maintained.
Model
Type
Resource Power
IP Addresses
KX-NS0110
DSP-S 61 1
KX-NS0111
DSP-M
125
KX-NS0112
DSP-L
252 2

16. 2-2. System Configuration (7)
Storage Memory Cards (SM) (Description) The NS1000 unit comes pre-installed with 2ch UM and 2hrs of Voice Mail recording capability. This can be increased to 15hrs by installing the KX-NSU001 A/K. The system VM recording capacity can be increased further by installing one of the optional SM cards.
Model
Type
Max Recording Time (Hrs)
KX-NS0135
SM-S
200
KX-NS0136
SM-M
450
KX-NS0137
SM-L
1000

17. 2-2. System Configuration (8)
Virtual Cards The NS1000 uses ‘virtual’ cards to support a range of IP based Trunks, Extensions, DECT Cell Stations and UM features. Virtual cards features can be activated with the appropriate activation key. Virtual Cards are configured via the Web-Based Maintenance Console.
Virtual Card type
Virtual Slot
V-SIPGW16
V-SIPEXT32
V-IPCS4
V-IPUM12
V-IPGW16
V-IPEXT32
V-UTEXT32
Ethernet
Other PBX
IP Telephony
Service
IP-CS
IP-PT
SIP-MLT/SLT 17

18. 2-2. System Configuration (9)
Virtual Cards (Specification)
Virtual Card Type
Description
Virtual 16-Channel VoIP Gateway
Card (V-IPGW16)
Virtual Card for 16-channel H.323 trunk. Compliant with VoIP H.323 V.5 protocol, and ITU-T G.729A and G.711 codec methods. Also supports T.38 protocol.
Virtual 16-Channel SIP Trunk Card
(V-SIPGW16)
Virtual Card for 16-channel SIP trunk. Compliant with RFC 3261, 3262, 3264, 3311, 3581, 3960 and 4028 protocols, and ITU-T G.729A and G.711 codec methods. Also supports T.38 protocol.
Virtual 32-Channel VoIP Extension
Card (V-IPEXT32)
Virtual Card for 32 IP-PTs (KX-NT300 series and KX-NT265 [software version 2.00 or later only]). Compliant with Panasonic proprietary protocol, and ITU-T G.729A, G.711 and G.722 codec methods.
Virtual 32-Channel SIP Extension
Card (V-SIPEXT32)
Virtual Card for 32 third party SIP phones. Compliant with RFC 3261, 3264, 3310, 2327 and 4028 protocols, and ITU-T G. 729A, G.711 and G.722 codec methods.
Virtual UT Extension Card
(V-UTEXT32)
Virtual Card for 32 KX-UT series SIP phones. Compliant with RFC 2327, 3261, 3264, 3310, 3515, 4028 and 4235 protocols, and ITU-T G.729A, G.711 and G.722 codec methods. Also supports WSD, CWMP and HTTP.
Virtual 4 IP Cell Station Interface Card
(V-IPCS4)
Virtual Card for 4 IP-CSs. Compliant with ITU-T G.729A and G.711 codec methods.

19. 2-2. System Configuration (10)
Activation Keys (A/K)
Activation Keys are required to activate the following features:
IP Trunk channel(H.323/SIP)
IP Telephone / Terminal capacity
Number of IP Telephones /Type of IP Telephones (IP softphone / IP-PTs / SIP Phones (UT series) / Other SIP Phones / IP Conferencing Phones)
Networking Features (One-Look, QSIG)
Unified Messaging Features (REC Time, 2-Way REC, Message Backup, UM Port capacity, UM/ (IMAP + Voice / Fax messages)
Mobile Phone Features
CA related Feature (Thin Client, CSTA Mux, CA Pro, CA Supervisor, CA Console, CA Networking)
CTI Interface (Allows use of Third Party CTI Application)
Packages containing a combination of different A/K’s are also available to equip users with key UM and Mobility features easily.

20. 2-2. System Configuration (11)
Activation Keys (A/K) – Cont.. The NS1000 is equipped with Preinstalled Permanent Activation Keys
Type
Feature
IP-PT License
8 IP PT (Used for NT or UT series PT)
UM License
2ch UM
CA Basic-Express
1022 Users
These A/Ks exist within the PBX hardware and cannot be deleted and will not expire.

21. 2-2. System Configuration (12)
Activation Keys (A/K) – Cont.. In addition to the pre-installed permanent A/Ks, there is the option to activate ‘trial’ A/Ks which are valid for 60 days. These trial A/Ks will expire 60 days after activation. Trail A/Ks cannot be re-activated by initializing the PBX system. Trial A/Ks (60 day expiry from activation)
Activation Key Type
Supported Mailboxes / Extensions / Features
One-Look Network -
Two-Way REC Control
Message Backup
UM / Users
128 Mailboxes
Two-Way REC Users
30 Two-Way REC / Two-Way Transfer Users
Mobile Users
30 Cellular Phone Users
CTI Interface
CA Pro
128 CA Pro User
CA Supervisor
1 CA Supervisor User
CA Console
1 CA Console User
CA Thin Client
CSTA Multiplexer

22. Supported Terminals Chapter 3
The chapter3 is Supported Card / Terminal.

23. 3-1. Terminal Compatibility (1)
New Range - SIP Telephone (UT Series)
Terminal Type
Compatible with NS1000 v1.0
SIP-MLT
UT133
YES
UT136
SIP-SLT*1
UT113
UT123
*1 UT113 : No backlit / UT123 : Backlit 23

24. 3-1. Terminal Compatibility (2)
Telephone Terminals
Terminal Type
Compatible with NS1000 v1.0
KX-NT3xx Series (IP-PT)
YES
KX-NT400 (IP-PT) NO
KX-NT7xx Series (IP-Conference Phone)
KXNCS81xx (IP-Softphone)
3rd Party SIP Phones
KX-DT3xx Series (New Digital PTs)
KX-T7xxx Series (Old Digital/Analogue PTs)
DSS Consoles (KX-T7640 Series etc)
SLTs (KX-7710 etc)
KX-NT265 IP-PT (V2.x)
KX-TCA155/255/256/355/356/TD7590/WT115 (Portable Stations)
KX-T30800 Series PTs and DSS Consoles
KX-T61600 Series PTs and DSS Consoles
KX-T Series PTs and DSS Consoles
KX-TD7500 DECT Portable Station
KX-NT265 IP-PT (V1.x)
KX-NT136 IP-PT
For compatible options (e.g., Add-on Key Module, USB Module, Headset), refer to the telephone’s manual. 24

25. 3-1. Terminal Compatibility (3)
Other Terminals
Terminal Type
Compatible with NS1000 v1.0
TDA0141CE 2ch CS (DPT IF) NO
TDA0142CE 4ch CS (CSIF)
TDA0158CE 8ch CS (DPT IF)
NCP0158CE 8ch CS (IP IF)
YES
A228 S/M-type battery backup cable
A229 L-type battery backup cable
A258 Blank Slot cover
T30865 Doorphone
T7765 Doorphone 25

26. Chapter 4
System Capacity

27. 4-1. System Capacity (1)
Type and Maximum Number of Slots The NS1000 supports the following type and number of slots.
Slot Type
Maximum Number
Stand-alone System
One-look Network
FAX Card Slot 1 16
Storage Memory (SM) Slot
DSP Card Slot 2 32
Free Slot
Doorphone Slot
Virtual Slot 20
Virtual Trunk Card
Virtual Extension Card
Virtual IP-CS Card

28. 4-1. System Capacity (2)
Maximum Optional Service Cards (1) The following number of cards can be installed in the Physical Slots of the PBX.
Card Type
Maximum Number
Stand-alone System
One-look Network
Physical Card 2 32
Line Card Slot 1 16
LCOT2+SLC2
BRI4+SLC2
PRI30+SLC2
Doorphone Slot
DPH1
Note
Any card that exceeds the capacity of the PBX will be ignored.
When the PBX starts up with an invalid configuration, some cards will be ignored.

29. 4-1. System Capacity (3)
Maximum Optional Service Cards (2) The following number of cards can be installed in the Physical Slots of the PBX.
Card Type
Maximum Number
Stand-alone System
One-look Network
DSP Card Slot 2 32
DSP-S 1 16
DSP-M
DSP-L
FAX Slot
FAX
Storage Memory Card Slot 1 16
SM-S
SM-M
SM-L
Note
Any card that exceeds the capacity of the PBX will be ignored.
When the PBX starts up with an invalid configuration, some cards will be ignored.

30. 4-1. System Capacity (4)
Maximum Optional Service Cards (3) The following number of cards can be installed in the Virtual Slots of the PBX.
Card Type
Maximum Number
Stand-alone System
One-look Network
Virtual Trunk Card 16
V-IPGW16 3 6
V-SIPGW16
Virtual Extension Card 20 32
V-IPEXT32 4
V-SIPEXT32
V-UTEXT32
V-IPCS4
Virtual Unified Messaging Card 2
V-IPUM12

31. 4-1. System Capacity (5)
Maximum Trunks and Extensions The PBX supports the following number of trunks and extensions.
Type
Stand-alone System
One-look Network
Total Number of Trunks
256
600
Trunk (Virtual Trunk Card)
H.323 Trunks 48 96
SIP Trunks
Trunk (Physical Trunk Card) 30
480
Total Number of Extensions
640
1000*1
Extension (Virtual Extension Card)
1000
IP-PT and IP Softphone
128
SIP Extension
Extension (Physical Extension Card) 2 32
*1 The maximum number of extension ports is 640 per PBX, and the maximum number of Unified Messaging ports is 24 per PBX. When 24 ports for Unified Messaging are fully activated on the Master unit, the maximum number of extension ports will be less than 640.
One Unified Messaging port is equal to 10 extension ports. Therefore, when all Unified Messaging ports are activated, only up to 420 extensions are available. (The 2 Built-in UM ports are not counted in this calculation).
This condition does not apply for Slave units or Stand-Alone units.

32. 4-2. Terminal Capacity
Maximum Terminal Equipment The following shows the number of each terminal equipment type supported by the PBX.
Terminal Type
Stand-alone System
One-look Network
Telephone
640
1000
SLT 2 32
IP-PT*1
128
SIP Phone
Wireless
IP-CS (8-channel) 64 PS
512
Unified Messaging (Channels) 24
384 (24x16)
Doorphone 1 16
Door Opener
External Sensor
*1 KX-NT300 series, and KX-NT265(v2.0).

33. 2-Way Recording (Users)
4-3. Feature Capacity
Maximum Feature capacity The following shows the maximum number of each feature supported by the PBX.
Type
Stand-alone System
One-Look Network
UM Mailbox
1024
16384
2-Way Recording (Users)
640
1000
Mobile Users
1152
CA Client Login Mode
Server-less
Server
Basic - Express
240
1022
Pro
Operator Console
128
Supervisor 4
NB: Total number of Login in Server Mode is 1022

34. 4-4. Email Client Capacity
Outlook Integration with built-in Unified Messaging The maximum number of IMAP clients using Outlook is 24 users per unit. (Reason: Outlook keeps the IMAP session open, even though then user is idle.)
Type of mailer
Outlook (+Tool Bar)*1
Other*2
# of UM Client 24
640
*1) This limitation is not applied if the user can use Outlook in “Offline” mode.
*2) which releases IMAP session when idle, such as Thunderbird, Lotus Notes etc.
Integration with POP
No limitation for users who receive voice data with an attachment.

35. THE END