AVANTE HYBRID Battery Dismantling Manual. Precautions for handling the hybrid battery Battery dismantling procedure Turning off the engine Disconnecting.

Slides:

Advertisements

Similar presentations

Unit 2- Electrical Components-continued EET 110 Electronics Survey I.

Advertisements

EXTRICATON TRAINING Pleasant View Fire

How to Safely Jump-Start Your Car. Jump-starting a car can be dangerous if proper procedures are not followed. Always consult your owners manual for specific.

Assembly / Disassembly / Reassembly Computers. Chapter Objectives After completing this chapter you will: Understand how static electricity can damage.

 Workshop induction. Hazards Magazine,

Cutting and Threading Steel Pipe

Portable Power Tool Safety. Portable Electric and Cordless Drill Be sure the electric drill is disconnected from the power source before installing bits.

SONATA HYBRID Battery Dismantling Manual. Precautions for handling the hybrid battery Wear rubber-insulated gloves. Use insulated tools. Do not have any.

Engine Removal and Disassembly

ES1000C/1500C Battery Replacement Procedure. 1.Pull off the front panel.

A UTO S AFETY T EST Part 3 - Equipment. J ACKS ARE USED TO : Hold a car up while working under it Raise a car Move a car Keep a car in place.

Two-mode Safety and Battery System Service

Marubot Football League Service Manual.

SD-SP P #1 Supplemental Restraint Systems. SD-SP P #2 Objectives Perform Proper SIR system disable procedure.

Qualified Electrical Worker

Chapter 19 Charging Systems.

TP4-ENERSOL-TD/PV double function

Hybrid Safety. 2 How Do You Identify A Hybrid? Vehicle displays “Hybrid” on the outside Dashboard shift label displays “Eaton Hybrid” Presence of bright.

Super Vac Smoke Ejector SECTION: Tools and Equipment ISSUED: REVISED: ##-####

1 Battery Safety, Servicing & Testing R. Bortignon.

Electrical Safety.

BATTERY CABLES AND WIRING IGNITION SWITCH NEUTRAL SAFETY SWITCH STARTER RELAY/SOLENOID STARTER MOTOR.

Reliability MANUAL CARTRIDGE UNLOAD Super DLT1 Presented By Quantum Technical Services.

Presented by: Stephanie Chan December 3, 2009 ENGL 393.

STARTER SYSTEM DIAGNOSIS AND SERVICE

Boosting a Car Battery Cables should have sufficient length (12-16-ft) with #6 gage stranded wire and well-designed clips. Follow the proper sequence of.

Hybrid Vehicles: High Voltage Circuit Disconnect Overview Whitney Kizer and Dr. Frank B. Flanders Georgia CTAE Resource Network Curriculum Office July.

© Goodheart-Willcox Co., Inc. Permission granted to reproduce for educational use only Battery Testing and Maintenance.

NFPA ELECTRIC VEHICLE SAFETY FOR EMERGENCY RESPONDERS Module V : Emergency Operations Module V : Emergency Operations 5-1.

Model 12 Intek Horizontal OHV

BOARD FEATURES  One/Double sided RED-GREEN board  Red player “OFF” – green player “ON”  Signals extra time in color of choise 

POWER TOOL SAFETY.

Copyright ©2014 ， JAE Electronics, Inc. Confidential DW Series Overview JAE May 2014 Battery Connectors for Power Storage.

Boost/Jump Starting SC3B Jump Starting a Vehicle With Jumper Cables By Vance Bloom.

BATTERY BOOSTING A battery may go ‘DEAD’ from many different causes. A ‘BOOST’ may be used to start a vehicle with a dead battery. Proper equipment and.

Hybrid Electric Vehicles 33 Introduction to Automotive Service James Halderman Darrell Deeter © 2013 Pearson Higher Education, Inc. Pearson Prentice Hall.

Automotive Fuel and Emissions Control Systems 3/e By James D. Halderman Copyright © 2012, 2009, 2006 Pearson Education, Inc., Upper Saddle River, NJ

Chapter 27 Restraint System Repairs. Objectives Explain the difference between an active and a passive restraint system Learn how to service seat belts.

Rapid Change Technology The following is a presentation to aid Technicians in the replacement of the Rapid Change Technology Block.

AVIVA™ ELECTRIC BIKES VIPER ASSEMBLY INSTRUCTIONS Aviva™ - For A New Way Of Life.

Mitsubishi I-MiEV Isolation Procedure.

Task Carry out routine maintenance of equipment and machinery.

Chapter 23 Interior Repairs. Objectives Identify the major parts of a vehicle’s interior Remove and replace seats, seat covers, and carpeting Service.

Description of Hand Tools Tools help us do work and make things. Tools.

Diagnosis and Troubleshooting of Automotive Electrical, Electronic, and Computer Systems, Fifth Edition By James D. Halderman © 2010 Pearson Higher Education,

Diagnosis and Troubleshooting of Automotive Electrical, Electronic, and Computer Systems, 6/e - By James D. Halderman Copyright © 2012, 2010, 2005, 2001,

Procedure for Use of Stihl Multisystem (Revision 0 – 18th January 2011) Toolbox Talk.

Genuine N1. Conversion Installation manual LC 120 5D 2003

OBJECTIVES After studying Chapter 40, the reader will be able to:

Teknologi Dan Rekayasa

Shaft Replacement Standard Operating Procedure

X-Spot Lamp Socket Replacement Procedure

HV Battery Assembly.

How To Replace YOUR Car Battery

installing electrical system

Servicing the Steering System

Qualified Electrical Worker

FIGURE 17-1 A visual inspection of this battery showed that the electrolyte level was below the plates in all cells.

MAINTENEANCE AND REPAIR OF STARTING SYSTEMS

Electrical Safety.

Computer Repair & Maintenance

DISCOVERING F.A.C.S. Kitchen Safety. DISCOVERING F.A.C.S. Kitchen Safety.

Body Electrical System

Electric Skillet Use Main cooking tool used in this unit.

A. Touching both terminals with the hands can cause electrical shock

Compressor Operating Instructions

Hybrid Safety and Service Procedures

Hybrid Electric Vehicles

Presentation transcript:

AVANTE HYBRID Battery Dismantling Manual

Precautions for handling the hybrid battery Battery dismantling procedure Turning off the engine Disconnecting the 12V battery terminal Disconnecting the safety plug and connectors Dismantling the hybrid battery Discharging the hybrid battery Wear rubber-insulated gloves. Use insulated tools. Do not have any metal objects in your possession while working. Do not cause any impact on the battery. Do not disassemble the battery without specific equipment. Be sure to discharge the battery to store and transport it safely.

Disconnection of the 12V battery terminal Caution Disconnect the negative terminal of the battery first. If the positive terminal is disconnected first, there is a possibility of electric shock. Disconnect the negative terminal. Unfasten a nut.Negative terminal of the 12V battery 12 3

Remove the rear seat back. Remove the rear seat cushion.Rear seat Removal of the rear seat Unfasten 2 bolts.

Turning off the safety switch Turn off the safety switch. Remove the safety cover. Safety switch in the ‘ON’ position After turning off the switch, wait 5 minutes for the electric discharge. Safety coverUnfasten a bolt and a nut

Disconnection of battery connectors (1) Connector / Terminals Disconnect the connector and terminals. Battery mounting frame / Front battery case 1 2 3

Caution Orange colored cables carry high current. Be cautious when working with electric terminals. Disconnection of battery connectors (2) Remove the frame and battery front case(LH). Unfasten 3 nuts.Unfasten 10 bolts. Nuts for fastening the battery case Unfasten nuts and disconnect terminals.High voltage terminals

Removal of trunk trims (1) Open the trunk. Loosen the fasteners.Remove the luggage center trim. Luggage center trim

Removal of trunk trims (2) Luggage side trim(RH) Remove the luggage side trim(RH).Complete removing trunk trims. Remove the luggage side trim(LH)

Detach the inlet cooling duct.Detach the outlet cooling duct. Unfasten 5 nuts.Outlet cooling duct / Inlet cooling duct Removal of cooling ducts

Dismantling the battery Take the battery out of the trunk. Finish dismantling the battery. Unfasten 3 bolts. Battery case Handle Dismantle the battery Caution Be cautious about transportation because a battery weighs about 35kg. Do not cause any impact on the battery.