Printing solutions as easy as Cosmos Mono M6 Firmware Update Guide Digital Printing Division Samsung Electronics Company, Ltd

2 Cosmos Mono M6 F/W Update Guide ■ Remarks before you proceed to upgrade Cosmos Mono M6 Firmware * Remark 1 : Remove Easy Job UI Application before upgrading M6 F/W. * Remark 2 : Switch the Debug Log in service mode to ‘Job Status’, the default status when it was set to ‘Details’ before upgrading M6 F/W. * If you need Easy Job UI after upgrading the M6 F/W, you should install one dedicated for M6. * Please take steps below to upgrade firmware. Ⅰ Ⅰ Remove Easy Job UI Application Memory extension Ⅱ Ⅱ Ⅲ Ⅲ M6 F/W Update (LUI) Estimated time to update M6 Appx. 1 M6 F/W Update (RUI) Appx. 2 Must Recommended HDD recovery Appx. 3 Conditions of re-building the hibernation image Appx. 4

3 Cosmos Mono M6 F/W Update Guide ■ How to remove Easy Job UI Application 1) Select [Machine Setup] 2) Select [Application Management]

4 Cosmos Mono M6 F/W Update Guide ■ How to remove Easy Job UI Application 3) Enter [ID / Password] 4) Find the [Easy Job] entry 5) Press [Uninstall] button

5 Cosmos Mono M6 F/W Update Guide ■ Install extension memory (512MB) 1) Remove 7 screws from back and open up upper rear cover 2) Find the memory slot inside video board 3) Plug the memory module on it

6 Cosmos Mono M6 F/W Update Guide ■ M6 Firmware Update Process (LUI) 1) Select [Machine Setup] 2) Select [Application Management] Insert USB stick here!

7 Cosmos Mono M6 F/W Update Guide ■ M6 Firmware Update Process (LUI) 3) Enter [ID / Password] 4) Press [Install] button

8 Cosmos Mono M6 F/W Update Guide ■ M6 Firmware Update Procedure (LUI) 5) Select [M6 Firmware Folder] 6) Select [Firmware] and press [Ok] button.

9 Cosmos Mono M6 F/W Update Guide ■ M6 Firmware Update Procedure (LUI) 7) [Firmware File] is being analyzed. 8) Check [Overwrite] button and click [Ok] button.

10 Cosmos Mono M6 F/W Update Guide ■ M6 Firmware Update Procedure (LUI) 9) [Firmware Update on progress] 10) After [Firmware Update completed], machine automatically reboots Message: << Update complete. Printer will reboot. >> * Remove USB memory stick after firmware update is completed.

11 Cosmos Mono M6 F/W Update Guide ■ M6 Firmware Update Procedure (LUI) 11)[Rebooting twice after Firmware Update ] Machine will reboot after firmware update and after hibernation snapshot image is created, it reboots again. Note In normal case, machine reboots 2 times sequentially in 2~3 minutes, and occasionally 3 or 4 times and it could take more than 3 minutes. 12) [Hibernation Snapshot Image creation] on the progress (takes 12 minutes) Warning Do not turn off machine during image creation Message: Don’t turn off the machine. It will reboot automatically after complete firmware update. Don’t turn off the machine. It will reboot automatically after complete firmware update

12 Cosmos Mono M6 F/W Update Guide ■ M6 Firmware Update Procedure (LUI) 13) [Hibernation Snapshot Image created] System is turning off on completion Message: Turning Off System. 14) [Reboot after image got created] Machine is booting up and preparing initial screen Message: Starting.. (Loading page)

13 Cosmos Mono M6 F/W Update Guide ■ M6 Firmware Update Procedure (LUI) 15) [Copy screen after reboot] 16) [HOME window]

Printing solutions as easy as [Appendix 1] Estimated time to complete M6 F/W Update

15 Cosmos Mono M6 F/W Update Guide ■ Estimated time frame of M6 Firmware Update * Time estimated in this table is just an example, your result may not corresponds with it StepDetails V5.N6.10 Time of steps Time of amounts Total time a Uninstall Easy UI before downloading firmware, Print 'Configuration Report' to check firmware version and size of memory bPower OFF and install additional memory(512MB) cPower ON dWaiting for machine get into the idle (copy screen) eGo to the home screen fMake print out of Configuration Report for checking firmware version and memory size 15 mins 1Starting upgrade to M6 Firmware 12:26 2Go to Application management and press install button [Msg: Analyzing...]00' 00" 3Check overwrite and proceed00' 54" 4UI screen changes [Msg: UI board is updating…]10' 43" 5UI screen changes [Msg: Update complete. Printer will reboot.]12' 03" 6Rebooting [Starting… (Initializing Network) /...]12' 56" 7Rebooting [Starting… (Initializing Network) /...]14' 07" 8 UI screen changes [Msg: Don’t' turn off the machine. It will reboot automatically after complete firmware update.] 16' 49" 9UI screen changes [Msg: Turning Off System..]26' 48" 10Rebooting [Starting… (Initializing Network) /...]28' 23" 11min 34secs 11Waiting for machine get into the idle (copy screen)30' 09" 12Go to the home screen33' 17" 33mins Make print out of Configuration Report for checking and perform basic test such as copy and print ACycle the power and measure booting time again.00' 00" BWaiting for machine get into the idle (copy screen)01' 19" CGo to the home screen01' 48"

Printing solutions as easy as [Appendix 2] Cosmos Mono M6 Firmware Update Guide (RUI)

17 Cosmos Mono M6 F/W Update Guide ■ M6 Firmware Update (RUI) 1) Enter Printer IP in Web Browser [ IP address]

18 Cosmos Mono M6 F/W Update Guide ■ M6 Firmware Update (RUI) 2) Press [ID] and [Password]. Ex) ID : admin, PW:

19 Cosmos Mono M6 F/W Update Guide ■ M6 Firmware Update (RUI) 3) Press [Maintenance].

20 Cosmos Mono M6 F/W Update Guide ■ M6 Firmware Update (RUI) 4) Press [Application].

21 Cosmos Mono M6 F/W Update Guide ■ M6 Firmware Update (RUI) 5) Press [M6 Firmware Folder] -> Select the [Firmware]. Press OK button.

22 Cosmos Mono M6 F/W Update Guide ■ EDC Hibernation Mode - EDC Mode (1+2+3 / 1934) –> Service Fumctions -> Hibernation Mode -> Create New Image ■ Hibernation Mode - OFF : Turn off ‘Hibernation Mode’ - ON : Turn on ‘Hibernation Mode’ - Create New Image : Create or refresh new Hibernation Image

Printing solutions as easy as [Appendix. 3] Cosmos HDD recovery guide

24 Cosmos Mono M6 F/W Update Guide ■ HDD recovery guide 1. How to get into ‘System Recovery’ mode A. Clear and Reset button combination 1) Press Clear+Reset button in the same time when booting progress bar is just grown up 2) Machine will reboot automatically 3) Get into ‘System recovery’ mode after reboot B. Unplug HDD method 1) Power off and unplug HDD cable 2) Power back on 3) System will get into ‘System recovery’ mode automatically 4) Plug HDD cable back 2. Proceed HDD recovery 1) Select HDD Format 2) Input passcode (1934) 3) Waiting for HDD format progress (Never reboot the machine until the end) 4) Plug USB if the machine prompts recovery image 5) Proceed recovery task

Printing solutions as easy as [Appendix. 4] Conditions of re-building the hibernation image

26 Cosmos Mono M6 F/W Update Guide ■ M6 Firmware - Conditions of re-building the hibernation image 1. H/W changes - Memory size - Fax card installation (Not count on un-installation) 2. S/W changes - https setting SWS -> Security -> Network security –> Secure Connection -> Secure HTTP - Service Mode HDD maintenance’s Data clear Service Mode > Hard Disk Maintenance’s all sub menus - HDD encryption setting Service mode ->Service functions->Hard disk maintenance->HDD Cipher setup - System recovery: when a device automatically executes system recovery after HDD checks. Service Mode > System Recovery - Manual installation SWS -> Maintenance -> Application Management -> Application - IP V6 option change SWS > Settings > Network Settings > TCP/IPv6 - Memory clear Tech mode > Service Functions > Main Memory Clear