1. New Hardware – Peripheral - 1
KX-NT136 (IP-PT)
Connection via IP
User Interface is same as TD7636.
Almost of KX-TD7636 Functions is in it.
PC-Phone/Console doesn’t work with.
PC Maintenance Console doesn’t connect.
(USB port is not supported)
Navigation Key
Dual color 24 Flexible Keys
Visible Large Ring/Msg Lamp
6 Lines 24 digits LCD /w backlit
RJ45
RJ11
TDA
LAN PC
Benefit
Remote Office, Easy moving in network, Cost saving

2. System Connection Diagram - 1
IP Connection PC
IP-PT
External Sensor/ External Relay Device
Remote PC PC
Trunk (Telephone Company Lines)
Analogue / BRI / PRI / T1 / E1
Private
IP Network
Router
Server PC PC PC
Batteries
SLT
DPT
APT
DSS
DPT
DSS
PC or Printer
T7633/36 PC
USB
T7600 DPT
DXDP
Doorphone & Door Opener
SLT CS
Wireless
Phone PS
BGM/MOH
Pager/
Speaker
Amplifier
FAX
ISDN
Telephone
Voice　Processing
System
Peripheral Connection
Legacy Connection

3. System Connection Diagram – 2PC
T7600 DPT
DPT
DSS
PT-IF CS PS
Voice
Processing
System
SLT
FAX
APT
Wireless
Phone
Same capability of DLC CS
LAN
Server PC
Doorphone & Door Opener
Pager/Speaker
Amplifier
Radio
DLC16 (TDA0172)
DLC8 (TDA0171)
DHLC8 (TDA0170)
MSLC16 (TDA0175)
SLC16 (TDA0174)
SLC8 (TDA0173)
CSIF4 (TDA0143)
CSIF8 (TDA0144)
CTI-LINK (TDA0410)
OPB3 (TDA0190)
DPH4 (TDA0161)
DPH2 (TDA0162)
ECHO16 (TDA0166)
MSG4 (TDA0191)
LCOT4 (TDA0183)
LCOT16 (TDA0181)
LCOT8 (TDA0180)
CID/PAY8 (TDA0189)
CID8 (TDA0193)
DID8 (TDA0182)
E&M8 (TDA0184)
BRI4 (TDA0284)
BRI8 (TDA0288)
PRI30 (TDA0290CE/CJ)
PRI23 (TDA0290)
T1 (TDA0187)
E1 (TDA0188)
IP-GW4 (TDA0480)
IP-GW4E (TDA0484)
MPR
MEC (TDA0105)
RMT (TDA0196)
PSU-S/M/L
TDA0108/0104/0103
Router
Batteries
SMDR PC
PSTN
Analogue
E&M
ISDN BRI
ISDN PRI T1 E1
Private
IP Network
EXT-CID (TDA0168)
IP-EXT16 (TDA0470)
LAN
IP-PT PC
IP-GW16 (TDA0490)
EIO4 (TDA0164)
External Sensor / External Relay Device

4. Function – Highlight
Function - Highlight

5. 16 ports IP-GW Card - 1 - model number is KX-TDA0490.
- 16ch IPGW Card occupies a Single slot in TDA100/200 Physical I/F single Ethernet 10/100BaseT (auto sense) LED’s - Status, Link, Data, Online, Alarm & Busy
- G729a/G723.1/G711
- T.38 (FAX) mode is not supported (FAX = G711)
- Configuration using Web browser (English)
- 100% call compatibility with TDA0484/3480
- Interoperability with TDA0480
Incoming call, Outgoing call and CLIP only.
- Interoperability with another manufacturers :
Not guaranteed.
- Power factor is 0.

6. 16 ports IP-GW Card - 2 Compatibility
The compatibility of the IPGW4 (TDA0480), IPGW4E (TDA484), IPGW16 (TDA0490) and the TDA30 IPGW4 (TDA3480) is described in the table below:
Compatibility
TDA0480
TDA0484/TDA3480
TDA0490
Signalling
H.323 V2
QSIG service
Proprietary
H.323 V4 Annex M1
Max networked IPGW’s
511
Voice Codec
G.723/G.729a
G.711/G.723.1/G.729a
FAX Protocol
T.38
G.711
Echo canceller
16ms
48/128ms
AGC
Yes No
DTMF Tone Detection
SNMP
Event Notice by
DHCP
Yes (Client)
NAT

7. 16 ports IP-GW Card - 3 Interoperability
The interoperability of the IPGW4 (TDA0480), IPGW4E (TDA484), IPGW16 (TDA0490) and the TDA30 IPGW4 (TDA3480) is described in the table below:
Function
TDA0480
connected to
TDA0384/TDA0484/TDA0490
Connected to
TDA0384/TDA0484/TDA0490
Connected to
TDA0480
CLIP OK OK OK
COLP OK OK No
COLR OK OK No
CNIP OK OK No
CNIR OK OK No
CONP OK OK No
CONR OK OK No
CT(Avoid Tromboneing) OK OK No
CF(Avoid Tromboneing) OK OK No
CCBS OK OK No
Making/Receiving Call OK OK OK
Fax Connection OK OK No

8. IP PT Extension (Benefit 1)
What is benefit of IP Extension
Two type wirings require two types of construction, maintenance and their time.
One type wiring save them.
Router
LAN
Router
LAN
IP-PT
Unified wiring give low cost construction and maintenance.

9. IP PT Extension (Benefit 2)
What is benefit of IP Extension
Normal Extension
IP Extension
Slot:301 Port:02
Slot:201 Port:01
LAN
Setting change will be required.
Just MOVE
EXT.201
EXT.201?
EXT.201
EXT.201
MOVE
IP-PT
IP-PT
Setting change is not necessary Easy & Quick move enable

10. IP PT Extension (Benefit 3)
What is benefit of IP Extension
Router
IP Network
Private
Leased
Line
IP-PT
PBX
LAN
Head Office
Branch Office
PBX is not necessary for Branch Office. All setting can be controlled by Head Office.

11. IP PT –1 (Sample Configuration)
Sample of configuration
Feature of IP PT(KX-NT136) is basically same as KX-T7636.
Except: OHCA, USB connection, 12CO Key connection, Digital XDP, and Walking Extension
Head Office
Branch Office
Private
IP Network
IP-PT
IP-EXT16
LAN
IP-PT
Secondary Ethernet Port
IP-PT 大石
3. IP PT Extension benefitと制限事項をきちんと記述する
(DHCP Server) PC
Primary Ethernet Port

12. IP PT –2 (Requirements) Requirements
- IP-EXT16 card is required.
-DHCP (Dynamic Host Configuration Protocol) Server is not supported by IP-EXT16 card.
You need to assign IP address of IP-EXT16 card by manual.
- Cable: 100 BASE-TX Category 5 or higher
- Power source: Power-over-Ethernet (PoE)
or KX-A237 AC Adaptor is necessary
Note: Following features are not supported.
OHCA, USB connection, 12CO Key connection, Digital XDP, and Walking Extension
IP-PT cannot be used for initial set-up of PBX system.

13. IP PT –3 (Programming IP-EXT. Card)
Programming Instruction
Step 1
Step 2
Step 3
Assign IP Address for IP-EXT. card by manual
Assign IP Address for IP-PT
Register IP-PT
IP Address & Subnet mask
(GW Address for IP-PT)
* If necessary (See page IP-PT7)
1. Configuration
1. Slot
2. System
14. IP Extension Setting
IP-EXT16
Property

14. IP PT –4 (Programming IP-PT)
Programming Instruction
Step 1
Step 2
Step 3
Assign IP Address for IP-EXT. card
Assign IP Address for IP-PT
Register IP-PT
At start up
2. Press “Enter” key at 1st installation or
1. Power on IP-PT
3. Select “Network”
2. Press “Set-up” soft key from 2nd time
LCD status
2. At 1st installation
Menu
Please first setup !
OK [ENTER]
3. Menu select
1. Start up
Menu
Network
PBX
VLAN
Maintenance
STORE
EXIT
CONT
ENTER
操作がわかりやすい絵とか写真とか考えて欲しい9/9
IPL Start…
Now Loading
2. From 2nd time
Searching…
Setup

15. IP PT –5 (Programming IP-PT)
Programming Instruction
Step 1
Step 2
Step 3
Assign IP Address for IP-EXT. card
Assign IP Address for IP-PT
Register IP-PT
With DHCP Server
(Automatic Assignment: IP Address for Subnet mask, IP-PT Default GW)
6. Assign IP Address for IP-EXT16 card
4. DHCP: Enable
5. Select “PBX”
7. Store
LCD status 4. 5. 6.
DHCP
Enable
IP Address
Subnet Mask
NEXT
Disable
EXIT
ENTER
矢印を太くしたほうがいい？
LCD表示と操作の関連がぱっと見てわかるようにならないか?
Menu
Network
PBX
VLAN
Maintenance
STORE
EXIT
CONT
ENTER
PBX IP Address ?
EXIT
CLER
ENTER

16. IP PT –6 (Programming IP-PT)
Programming Instruction
Step 1
Step 2
Step 3
Assign IP Address for IP-EXT. card
Assign IP Address for IP-PT
Register IP-PT
Without DHCP Server
4. DHCP: Disable
5. Select “IP-Address”
6. Assign IP Address for IP-PT
8. Assign IP Address for Subnet mask
7. Select “Subnet mask”
* 9. Select “Default GW”
*10. Assign IP Address for Default GW
12. Assign IP Address for IP-EXT16 card
11. Select “PBX”
13. Store
LCD status
4. – 8.
11.
12.
DHCP
Enable
IP Address
Subnet Mask
NEXT
Disable
EXIT
ENTER
操作と画面の関連がぱっとわかるようにならないか？
Menu
Network
PBX
VLAN
Maintenance
STORE
EXIT
CONT
ENTER
PBX IP Address ?
EXIT
CLER
ENTER

17. IP PT –7 (Programming IP-PT)
Programming Instruction
Step 1
Step 2
Step 3
Assign IP Address for IP-EXT. card
Assign IP Address for IP-PT
Register IP-PT
Without DHCP Server
Head Office
Branch Office
Router
Router
Private
IP Network
Gateway:
Gateway:
IP-EXT16
IP-PT
IP-PTからする設定でいやらしいGATEWAYの設定があったはずby Mr.Take
LAN
DHCP
Enable
Default Gateway
PREV
Disable
EXIT
ENTER
IP-PT PC

18. IP PT –8 (Register IP-PT to PBX)
Programming Instruction
Step 1
Step 2
Step 3
Assign IP Address for IP-EXT. card
Assign IP Address for IP-PT
Register IP-PT
Select: ON
Registration
Registration:Start
UNREGISTERED TO SERVER
OK[ENTER]
LCD of IP-PT is changed to normal
アブノーマルな状態(登録前の状態)のLCD表示も追加すること
30 SEP. 11:09AM FRI
PROG
INFO
RING
MENU
1. Configuration
15. IP-Extension Port
Confirm: OK

19. IP PT –9 Virtual LAN VLAN(L2 Switch) Necessary Information
VLAN Name : Sales
ID : 1
Port on VLAN: 1-4
Tagged VLAN: Null
PHY. Port
VLAN No
VLAN(L2 Switch)
Necessary
Information
Local Office
Remote Office
IP-PT EXT.101
IP-PT EXT.102
IP-PT EXT.103
IP-PT EXT.104
IP-PT IP Address
Subnet Mask Address
Default Gateway Address
Card IP Address
VLAN ID 1
VLAN ID is necessary for IP-PT when you connect PC to IP-PT

20. IP PT –10 Virtual LAN Branch Office Head Office Private IP Network
Router
L2 switch configuration
VLAN Name : Sales
ID : 1
Port on VLAN: 1-4
Tagged VLAN: Null
PHY. Port
VLAN No
L2 Switch
Gateway:
Gateway:
IP Network
Private
Branch Office
Head Office
VLAN ID = 1
VLAN ID = 1
IP-EXT16
LAN
VLAN ID = 1
VLAN ID = 1
IP-PT
IP-PT
VLAN ID = 1
LCD status
VLAN ID = 1
VLAN ID って何?設計者に竹さんが確認。思うではなく事実を確認。
Menu
Network
PBX
VLAN
Maintenance
STORE
EXIT
CONT
ENTER
VLAN
Enable
Primary port
Secondary port (TO PC)
Disable
EXIT
ENTER
Primary port
VLAN ID
VLAN Priority 1 7