Presentation is loading. Please wait.

Presentation is loading. Please wait.

Confidential1 Panasonic Communications Co., Ltd. Network Business Company Edition 1.3 07 Jul., 2004 Enhanced Items KX-TDA200/100 System (Ver.1.1)

Similar presentations


Presentation on theme: "Confidential1 Panasonic Communications Co., Ltd. Network Business Company Edition 1.3 07 Jul., 2004 Enhanced Items KX-TDA200/100 System (Ver.1.1)"— Presentation transcript:

1 Confidential1 Panasonic Communications Co., Ltd. Network Business Company Edition Jul., 2004 Enhanced Items KX-TDA200/100 System (Ver.1.1)

2 Confidential2 General -System Highlight - New Features - Condition of New Features - Software Compatibility

3 Confidential3 V1.0 V1.1 Networking(QSIG), Call Center, VoIP Gateway, CTI (CSTA/TAPI), T76xx Line Up, Wireless System - Digital XDP & Double Extension Capacity by MEC - New VoIP Gateway Card (Panasonic proprietary) - New CS to DPT Port - And other new features System Highlight

4 Confidential4 BRI4, IPGW4E, CSIF4, 2chCS, MEC DXDP & Double Extension Capacity New IPGW Card 2chCS Broadcasting Dialing Plan Ext. CLIP sending on Emergency Call Short Cut Access to System Speed Dial Modified DDI Number is displayed on LCD Improved DSS LED Flash / Call Pick up Disable Hold Recall Disable re-count Ext-CO Duration Limitation by Hold Retrieve ISDN-3party Conference DTMF Tone through a Conference from PT Intercept Timer for each time mode(Day/Night/Lunch/Break) SMDR RC/AN information output Paging to other paging group COS Name is programmable CS port Name is programmable Ext. CLIP Automatic Generating DDI/DID Name Automatic Generating Wireless XDP Programming from PC Logical Check PS Hand-Over during Conference Call Walking Extension from Fault Extension Hardware Function Improvement Highlight Making calls Receiving calls Hold/FWD/TR Conference Timer Others Programming New Features

5 Confidential5 New Features DXDP Double Extension Capacity 2chCS Broadcasting Another Features Software Condition DHLC/DLC = No Hardware Condition No MEC(TDA0105) No MEC(TDA0105) No Condition of New Features

6 Confidential6 Software Compatibility MPR / LPR MPR 1.1xxMPR 1.0xx YES YES w/o DXDP, TDA0141 YES DLC/DHLC DLC/DHLC 1.xxx MPR / PC maintenance console MPR 1.1xxMPR 1.0xx YES NO YES

7 Confidential7 Hardware - New Hardware - Power Factor Summary

8 Confidential8 CSIF4 (4 Cell Station Interface) KX-TDA port CS interface card for 4 CSs(TDA0142). MEC (Memory Expansion Card) KX-TDA0105 2ch CS (CS to DPT Port) KX-TDA0141 * Memory expansion for - Broadcasting feature - Double the number of DPTs (DXDP) * To be installed in the MEC slot on MPR card Connect to DPT port (CSIF card is not needed) 2.4GHz (KX-TDA0141), DECT(KX-TDA0141CE) IPGW4E (4ch VoIP Gateway) KX-TDA0484 TDA200 4 TDA100 2 TDA200 4 TDA100 2 TDA200 1 TDA100 1 TDA TDA channel VoIP gateway VoIP H.323 V.2, ITU-T G.729a, G.723.1, G.711 T38 (FAX) is not supported Panasonic proprietary IPGW card New Hardware

9 Confidential9 * Calculated with base card, not using base ports. IPGW4 PRI-30 BRI-8 BRI-4 CID (CO) E1 E&M LCOT-16 LCOT-8 LPR Card TDA0480 TDA0290 TDA0288 TDA0284 TDA0193 TDA0188 TDA0184 TDA0181 TDA0180 Model Power units IPGW4ETDA04840 MSG RMT TDA0191 TDA CTI-LINKTDA04100 Echo DPH-2/4 TDA0166 TDA0161/ MECTDA01050 Trunk Card Extension Card Other Terminals Voice Mail (D-PT) T72xx/T74xx/T75xx BRI Extension T76xx, T7560, T75651/Extension 2/Port (2ch) 4/Extension 2/Port (2ch) CS (TDA0142)4/CS CS (TDA0141)4/CS APT & DSS console4/Extension SLT0 MSLC-16 SLC-16 DHLC-8 DLC-16 DLC-8 SLC-8 LPR CardModelPower units CS I/F-8 TDA0175 TDA0174 TDA0170 TDA0172 TDA0171 TDA0173 TDA /Card* 8/Card* CS I/F-4TDA01430 Power factor summary (Ver. 1.1)

10 Confidential10 Function - Highlight - DXDP & Double Extension Capacity - New IPGW Card - 2ch CS

11 Confidential11 - DPT on DPT without additional HW or SW - Easy installation for additional Extensions - 1 DHLC port => 3 telephones (2x DPT+1x SLT) * DHLC Card = Max 24 Ext. - 1 DLC port => 2 telephones (2x DPT) * DLC16 Card = Max 32 Ext. * DLC8 Card = Max 16 Ext. DXDP-Slave XDP or 4 Wires 2 Wires XDP 4 Wires 2 Wires DHLC Port SLT SLT DXDP-Master 2 Wires DXDP-Slave 2 Wires DLC Port 2 Wires DHLC Port SLT Digital XDP (DXDP) -1

12 Confidential12 Capacity for Extension V1.0V1.1 DXDP MEC TDA100 TDA200 No Yes No Yes Max 64 Ext. Max 128 Ext. Max 64 Ext. Max 128 Ext. Max 256 Ext. Additional DPT can be installed without buying another DHLC or DLC, but total capacity does not change without MEC. System Capacity (Trunk & Extension mixed) V1.0 TDA (108) ports TDA (216) ports V1.1 with DXDP&MEC TDA (158) ports TDA (316) ports Digital XDP (DXDP) -2

13 Confidential13 MEC(TDA0105) How to check the TDA0105 If the TDA0105 is not installed. If the TDA0105 is installed. Click” If connected extension is exceed 128 with M type PSU, what happens? - 129th Extension (PT) will not come in service. - Minor error log = PT Connection Over. DHLC-88 (Fixed) + Connected PT/DSS/VM SLC-88 (Fixed) DLC-8Connected PT/DSS/VM SLC-1616 (Fixed) DLC-16Connected PT/DSS/VM PU for extension cards Digital XDP (DXDP) -3

14 Confidential14 Condition-3 - OHCA function can not be used - T7601 (USB) can not be used (PC Phone / PC Console / PC Programming) MasterSlave - T T T T T T T T T T7665 Telephone Can be used - A-PT - T72xx - T74xx - T75xx - DSS - A-PT - T72xx - T74xx - T75xx - DSS - CS Can not be used Condition-2 DXDP-Slave ø0.4mm Max.40m ø0.5mm Max.50m ø0.6mm Max.60m DXDP-Master Condition-1 ø0.4mm Max. 500m ø0.5mm Max. 720m ø0.6mm Max. 830m Condition-4 Parallel Connection !No! Digital XDP (DXDP) -4

15 Confidential15 - 4ch IPGW Card - G729a/G723.1/G711 - T.38 (FAX) mode is not supported (FAX = G711) - Physical I/F: 10/100 Base-T - Web programming (English) - Interoperability with TDA0480: Incoming call, Outgoing call and CLIP only. - Interoperability with another manufacturers : Not guaranteed. 1 st Time Setup Connection TDA100/200 TDA /100 Base-T Cross Cable (http:// ) Pattern 1 TDA100/200 TDA /100 Base-T Straight Cable Switching HUB (http:// ) Pattern 2 IE5 or later General VoIP Gateway Card (KX-TDA0484) - 1

16 Confidential16 VoIP Gateway Card (KX-TDA0484) - 2 No Proprietary 511 G.723/G.729a T.38 16ms Yes No H.323 V2 Yes (Client) H.323 V4 Annex M1 511 G.711/G.723.1/G.729a G ms No Yes No H.323 V2TDA0480TDA0484/TDA3480Compatibility DHCP QSIG service Max networked IPGW cards Voice Codec FAX Protocol Echo canceller G.165/G.168 AGC DTMF Tone Detection SNMP Event Notice by NAT Signalling New IPGW Card (Compatibility)

17 Confidential17 VoIP Gateway Card (KX-TDA0484) - 3 New IPGW Card (Interoperability) TDA0480 connect to TDA0480 OK TDA0484/TDA3480 connect to TDA0480 No OK No TDA0484/TDA3480 connect to TDA0484/TDA3480 OK Function CLIR COLP COLR CNIP CNIR CONP CONR CT(Avoid tromboned) CF(Avoid tromboned) CCBS CLIP Making/Receiving call FAX Connection

18 Confidential18 How to connect TDA0480 & TDA0484… Outline of example TRG2 IP_Address: IP_Address: Subnet Mask: Default GW: IP_Address: TDA0484TDA0480 Ext.102 TIE Access = 7 Ext.103 TIE Access = 7 PBX Code = 81 PBX Code = 82 Switching HUB Dial = [7]+[82]+[103]  103 of PBX82 Dial = [7]+[81]+[102]  102 of PBX81 TIE Routing Table Lead : 82 Remove : 0 Added : none Trunk : 02 TIE Routing Table Lead : 81 Remove : 0 Added : none Trunk : 02 A-low VoIP Gateway Card (KX-TDA0484) - 4

19 Confidential19 TDA0484 Setting * Address Setting (IP Address of Card) 1.Programming 1.1 Network Settings, General IP Address Setting IP Address : Subnet Mask: Default GW : * Handling setting for Incoming Call from IP Network 1.Programming 1.5 Hunt Pattern (for Incoming Group) Hunt Group Grp1 = Port 1 & Port 2 Grp2 = none Hunt Pattern 1: Rcv Leading Digit = 81, Hunt Group = 1 Port 1Port 2 BRI -QSIG Incoming PBX Code = 81 TDA0484 TRG 2 BRI -QSIG TRG 2 IP Network Outgoing * Handling setting for Outgoing Call from PBX to IP Network 1.Programming 1.6 DN2IP (Dialed Number to IP Address Translation) GW Entry DN2IP Entry GW No.= 1 Comment = 82 Office, TDA0480 IP Address = Group No. = 0 Leading No. = 82 Remaining Number of Digits = 3 GW No./Group No. Selection = GW GW No./Group No. = 1 1.Programming 1.4 VoIP Gateway/IP-PBX Interface Settings Others G711 A-Law * Interface between IPGW & PBX VoIP Gateway Card (KX-TDA0484) - 5

20 Confidential20 General Tab IP Address : Subnet Mask : Rout Address 1: Rout Address 2: none Trunk Data Tab Port1 Trunk Group #1 Interface type = Basic Interface Length of call reference = 1 Port2 --- same as Port1 Configuration = QSIG Hunt pattern Tab --- Incoming call Handling Destination Number = 82 Hunt pattern = 1 Trunk priority Tab Hunt pattern 1: Priority1 = Trunk group#1 (Default) Other Tab A-law/m-law flag = A-law DNS Editing Terminal = 81 Remaining digits = 3 Selected unit = TDA0484 Unit ICON TDA0480 Setting Configuration procedure 1. Configure TDA0480 own setting 2. Create “Other Unit” --- TDA0484 IP Address 3. Edit DNS table and send to TDA Reset PBX after sending all data for TDA0480 VoIP Gateway Card (KX-TDA0484) - 6

21 Confidential21 GW Grouping (Slide Call feature) In the case that TDA has more than an IP-GW, you can group these IP-GWs. IP Network Grouping Benefit of the GW Grouping : Slide Call In the case that the IP-GW(a) is not available because all channels are in use for example, originating IP-GW try the IP-GW(b). IP Network Not available Originating IP-GW IP-GW(b). IP-GW(a). VoIP Gateway Card (KX-TDA0484) - 7

22 Confidential22 TDA0141&TDA0142 total Max.32 CS / TDA200 Max.16 CS / TDA100 4 PU / CS - Two Voice Paths per CS. - A specific CS I/F card is not needed. - A port on DHLC and DLC cards can used as the interface for KX-TDA Max. number of CS: TDA100=16 TDA200=32 (Including TDA0142). - DHLC/DLC cards software must be or later. - Functionality : The same as TDA Hand-over TDA0141  TDA0142: “YES” - Power factor is 4. - CS Port assignment is not needed. The TDA automatically detects the connected CS (as same as DPT connection). DHLC DLC TDA0141 TDA0144 TDA0143 TDA0142 ø0.4mm 222m ø0.5mm 347m (CAT5) ø0.6mm 500m 2ch Cell Station (KX-TDA0141) -1

23 Confidential23 How to update the CS software 1- Set a CS port to “OUS” 2- Go to “SD Card File View and Load” 3- Select “PDCSDECT” (or “PDCS24G”) 4- Click “Detail” 5- Take the same procedure of Ver.1.0 2ch Cell Station (KX-TDA0141) -2

24 Confidential24 Function – Making Calls - Broadcasting - Dialing Plan - Ext. CLIP sending on Emergency Call - Short Cut Access to System Speed Dial

25 Confidential FWD to somewhere The caller receives C.Tone for each time. No Ring An PT user (Owner) can make one way path call (= announce) to 31 parties simultaneously. After one of called party answering, the owner can begin announcement. This feature requires MEC(Memory Expansion Card : KX-TDA0105). Configuration Wired Extension - PS -Other PBX’s Extension (Only Closed Numbering)* - Outside Telephone Number * *: Only available when the networking type of the trunk is assigned as private. * Up to 32 digits [1][*32]+ Announce C.Tone One Way Path Max.31 members 8 Groups / System busy tone If no member answer, I cancel broadcasting and send busy tone to the caller. 2.System - 4.Timers & Counters - 2.DISA/DPH/CONF/T.Reminder "Answer Waiting Timer for Broadcasting Group (s)" = Because of DND / PS in XDP Parallel Restriction from TRS/Barring / Call Charge Limit Operation Off-Hook Override FWD setting In case of No Answer, it will be disconnected by timer. COS: “Broadcasting Operation” = Enable Owner PT only Broadcasting - 1

26 Confidential26 Announce 211 Member Member Member Member Member-05 Joining Order 1 st nd rd The owner Conversation during broadcasting 1.To let members join to conversation 2.To let members leave from conversation (1) The Owner pushed [DSS - 212] => Ext.212 join to conference (2) The Owner pushed [Conf.] => Youngest Member (=Ext.211) join to conference (3) Listening Member pushed [DSS - 201] or Recall/Hookswitch => Notification Tone goes to the owner, Member’s information appear on the Owner’s LCD. => The Owner push [DSS - 214] => Ext.214 join to conference Notification Tone LCD: Ext.214 wants conversation ! Ext By (1) Ext By (2) Ext By (3) (1) (2) (3) Push [DSS-211] Push [Transfer] Push [Flash/Recall] In above situation, when the owner does following action… Ext.211 goes back to be a listener Last joined member (=Ext.214) goes back to be a listener Last joined member (=Ext.214) is disconnected from broadcasting. Conversation with the Owner Max.3 Members = Max.3 Members ( 4 Party Conference ) Broadcasting - 2

27 Confidential27 Broadcasting - 3 From an owner Extension, Dial *32 + Broadcasting group number When a member of the group answers the call. Conference : 2 Conference No of member LCD Display in typical condition In establishing Owner Extension Called Extension Conference1: PCCUK Owner Extension Called Extension In broadcasting Name of Broadcasting Group

28 Confidential28 Broadcasting - 4 Additional information Internal Call Block is Block Set to Call FWD Set to DND Busy Auto Answer Wireless XDP PS Condition of Member Ext. Response for Arriving Broadcasting Call The broadcast call arrives this extension. The broadcast call does not arrive this extension. Call Waiting function will be performed. The Auto Answer function will not be performed. The broadcast call does not arrive this PS. The broadcast call does not arrive this extension. Conditions and Responses of Member Extension If owner extension has DSS key of a member of broadcasting group and establishes a broadcasting call, the DSS key does not flash when the called extension rings. It actually turns red (not flashing). DSS key of Owner Extension which relates with member extension

29 Confidential29 Dialing Plan Table for each TRG (Table1 – Table4) Max.32 digits 4 Tables independently 1: N11 2: NXXXXXX 3: 1NXXNXXXXXX 1: N11 2: NNXXXXX 3: 1NPXNXXXXXX 1: N11 2: NXXXXXX 3: 1NNXXXXX 4: 1NPXNXXXXXX 1: N11 2: NXXNXXXXXX 3: 1NXXNXXXXXX 48: N11 49: NXXXXXX 50: 1NXXNXXXXXX Type-A Type-B Type-C Type-D Type-E N = 2-9 P = 0,1 X = 0-9,*,# Max.50 leading numbers Voice Path Tx: Mute Rx: OK ( during Dialing ) PBX recognizes the end of dialing! Voice Path Tx: OK Rx: OK Voice Path Tx: OK Rx: OK ( Start of Dialing ) ( End of Dialing ) Dialing Plan is working Dialing Plan is not working Inter Digit Timer expired ! Making a Call with Analog CO Inter Digit Timer 1-15s - PBX can know the end of dialing by Dialing Plan Table. - It works for ISDN Enblock dial mode and Analog CO. - Typical configuration by “Auto Assign”. (Type A/B/C/D/E) - Dialing Plan Table is assigned for each TRG. - PBX sends all of the dialed digits at once after all digits dialed. Dialing Plan

30 Confidential30 It overrides CLIR / CO Line CLIP. Ext.CLIP is sent to PRI public network as “Location Identification Number”, even if CLIR is set or CLIP mode is “CO Line CLIP”. -This feature works only for Emergency call. - “E911 service” must be enabled. Yes Ext. CLIP sending on Emergency Call

31 Confidential31 [Auto] + [JOG] or [Navi-Down/UP] works as short cut key. --- TDA30 V1.0 too - TDA100/200 Ver.1.0 “AUTO DIAL” Nothing Happens - TDA100/200 Ver.1.1 (TDA30 Ver.1.0) “AUTO DIAL” System Directory Name ?> “  ” or “  ” Allen, David Allen, Steve Azure, Alf      “ENTER”  Daly, Gill Darcy, Nigel Davies, Allan  Short Cut Access to System Speed Dial

32 Confidential32 Function – Receiving Calls - Modified DDI Number is displayed on LCD - Disable DSS Flash

33 Confidential33 - TDA100/200 Ver TDA100/200 Ver.1.1 ISDN (CLIP) Line 001: 201 (DDI) Caller Ext. 201: DDI (CLIP) Line 001: (DDI) DDI Table DIL Table & Port setting ISDN Ext. 201: DDI Caller Modified DDI Number is displayed on LCD

34 Confidential34 - TDA100/200 Ver.1.0 Ext. 201 External Call to Extension directly The DSS LED on Ext.202 is flashing. The call can be picked up by pressing the button. - TDA100/200 Ver.1.1 Two options: - The DSS LED on Ext.202 will flash. The call can be picked up by pressing the button. - The DSS LED on Ext.202 will turn ON. The call cannot be picked up by pressing the button. Busy tone is sent if the DSS button is pressed. External Call New program item Enable: DSS LED will flash Disable: DSS LED will turn ON All DSS LED’s flashing look like a Xmas tree.  Annoying!!! Ext Improved DSS LED flashing/Pick up call -1

35 Confidential35 - TDA100/200 Ver.1.0 External Call to ICD-Group directly The DSS LED on Ext.202 flashes. The call can be picked up by pressing the button. - TDA100/200 Ver.1.1 Two options: - The DSS LED on Ext.202 will flash. The call can be picked up by pressing the button. - The DSS LED on Ext.202 will turn ON. The call cannot be picked up by pressing the button. Busy tone is sent if the DSS button is pressed. New item Enable: DSS LED will flash Disable: DSS LED will turn ON Ext. 201 Ext External Call ICD-G 280 Improved DSS LED flashing/Pick up call -2

36 Confidential36 It is possible to disable DSS LED’s turning off for an incoming call. New item ON or Flash: DSS LED turns ON or flashes for an incoming call. OFF: DSS LED never turns ON nor flashes for an incoming call. If the DSS button is pressed when extension is ringing, Busy Tone LED : ON It is possible to pick up call LED: Flashing Call pick up by DSS key = Disable Call pick up by DSS key = Enable DSS Key mode = ON DSS Key mode = OFF Call arrives at extension LED: OFF Improved DSS LED flashing/Pick up call -3

37 Confidential37 Function – Hold/FWD/TR - Disable Hold Recall - Disable re-count Ext-CO Duration Limitation

38 Confidential38 Disable Hold Recall is available if Hold Recall Timer is : Hold Recall works 0 : does not work V1.0 does not have. Disable Hold Recall

39 Confidential39 Disable re-count Ext-CO Duration Limitation by Hold Retrieve Extn-CO Duration Timer Calling PartyCalled Party Call dest. Party Place on Hold Hold Retrive Answer Ringing (Establishing a Call) (In Conversation) (On Hold to transfer) (In Conversation) Time flow Start ReStart Start V1.0V1.1 - Ext 201 makes an external call. - Extension-CO duration timer on Ext 201 starts when the external party answers the call. - Ext 201 transfers the call to Ext 202. Extension-CO duration timer on Ext 202 re-starts when Ext 202 answers the call. Extension-CO duration timer on Ext 201 continues on Ext 202. V1.0 V1.1 Concrete example Disable Re-counting Ext-CO Duration Timer

40 Confidential40 Function – Conference - ISDN – 3 party Conference - DTMF Tone through a Conference from PT

41 Confidential41 2nd Party 1st Party Adding a Third Party during a conversation using an ISDN service (Three-party Conference [3PTY] via ISDN) Standard : ETS New ISDN It is not service item for Euro-ISDN ISDN – 3 Party Conference (EURO-ISDN) -1

42 Confidential42 How to establish a conference (During a conversation) Press ISDN-Hold ISDN -Hold Dial desired phone number Talk to the new party 3-party conference Press CONF Dial desired phone number Talk to the new party 3-party conference Press Transfer PT/PS Enter ISDN – 3 Party Conference (EURO-ISDN) -2

43 Confidential43 - This will be useful for two parties to listen to VM message. SLT Voice Mail PT ( Conference ) DTMF Tone DTMF Tone Not only SLT user but also PT user can control Voice Mail. Voice Mail control during conference call. SLT PT YES(Can send DTMF) NO(Cannot send DTMF) YES(Can send DTMF) V1.0V1.1 DTMF Tone Through to Conf.Call from PT

44 Confidential44 Function – Timer - Intercept Timer for each time mode

45 Confidential45 Intercept timer and DISA intercept timer can be programmed for each time service mode. Intercept Timer for Day / Lunch / Break / Night Intercept Timer DISA Intercept Timer 1-60 s : Enable 0 s : Disable s Intercept Timer For Each Time Mode

46 Confidential46 Function – Others - SMDR RC/AN Information Output - Paging to Another Paging Group

47 Confidential47 RC (Receive Call) information, it will be output when TDA receives incoming call. AN (Answer Call) information, it will be output when extension user answered incoming call. * SMDR Type format is not changed from V1.0 (Type A / B / C). * KX-TD SMDR based application can work. * But some of them can not work properly. Because the detailed Spec. and timing to output is not same as KX-TD series. Programming is needed. -No Print (Default) -Print SMDR RC/AN Information Output -1

48 Confidential48 Output Samples-1 20/02/04 07:48AM RC 20/02/04 07:49AM '56 00:00'00NA - External Call  Extension (201)  No answer  Caller disconnects 20/02/04 08:22AM RC 20/02/04 08:22AM '11AN  Ext. 201 Answers 20/02/04 08:22AM '11 00:00'17 - External Call  Extension (201)  Answers  Disconnects - External Call  DISA (270)  OGM is sent  No Answers  Caller disconnects 20/02/04 09:00AM RC 20/02/04 09:00AM '05AN  DISA Answers 20/02/04 09:01AM '05 00:00'19D0 20/02/04 09:04AM RC 20/02/04 09:04AM '05AN  DISA Answers 20/02/04 09:05AM '05 00:00'09D0  Ext. 201 Answers 20/02/04 09:05AM '00 00:00'12TR - External Call  DISA (270)  OGM is sent  Ext. 201 answers  Disconnects Output Samples-2 (DISA) SMDR RC/AN Information Output -2

49 Confidential49 - External Call  ICD-G (280)  Time table is not started  No Answers  Caller disconnects Output Samples-3 (ICD-G) 20/02/04 08:42AM RC 20/02/04 08:42AM '05 00:00'00NA 20/02/04 08:36AM RC 20/02/04 08:37AM '10AN  Time table starts 20/02/04 08:37AM '10 00:00'19 -External Call  ICD-G (280)  Wait  Time table starts  No Answers  Caller disconnects - External Call  ICD-G (280)  Time table is not started  Ext.201 Answers  Disconnect 20/02/04 08:49AM RC 20/02/04 08:49AM '04AN  Ext. 201 Answers 20/02/04 08:49AM '04 00:00'00 20/02/04 08:49AM '00 00:00'06 -External Call  ICD-G (280)  Wait  Time table starts  Ext.201 Answers  Disconnect 20/02/04 10:48PM RC 20/02/04 10:48PM '05AN  Time table starts 20/02/04 10:48PM '05 00:00'12  Ext.201 Answers 20/02/04 10:48PM '00 00:00'06 - External Call  ICD-G (280)  Time table starts  No Answers  Caller disconnects 20/02/04 10:57PM RC 20/02/04 10:57PM '00AN  Time table starts 20/02/04 10:57PM '00 00:00'17 SMDR RC/AN Information Output -3

50 Confidential50 - No additional programming steps are required. - Operation is not changed from V1.0. ( [*33]+[PageG.Number(2digits)] ) - TDA100/200 Ver.1.0 Ext. 201 User Group-01 Ext. 202 User Group-02 Paging Group-01 Ext. 203 User Group-03 Ext. 204 User Group-04 Paging Group-02 NO YES - TDA100/200 Ver.1.1 Ext. 201 User Group-01 Ext. 202 User Group-02 Paging Group-01 Ext. 203 User Group-03 Ext. 204 User Group-04 Paging Group-02 YES Paging to Another Paging Group

51 Confidential51 Function – Programming - Programmable COS Name & CS Name - Ext. CLIP Automatic Generating - DDI/DID Name Automatic Generating - Wireless XDP Programming from PC

52 Confidential52 - TDA100/200 Ver TDA100/200 Ver.1.1 COS name CS name Both 20 Characters Programmable COS Name & CS Name

53 Confidential53 CLIP: Delete digit Increase this number New function => Delete from left Max. 16 digits,( 0 – 9 * # ) Ext. CLIP Automatic Generating

54 Confidential54 PCC00-UK PCC -UK Delete digit Increase this number PCC00-UK PCC01-UK PCC02-UK PCC03-UK New function Max. 20 characters => Delete from left DDI/DID Name Automatic Generating

55 Confidential55 It is possible to program Wireless XDP connection from the PC maintenance console. - Assign Wireless XDP PS number. - Click “Apply” - Power off-on the Wireless XDP PS for enabling this programming. Wireless XDP Programming from PC

56 Confidential56 Improvement - Logical Check - PS Hand-over during Conference Call - Walking Extension from Fault Extension

57 Confidential57 1. System - System Operator PBX-Operator 2. Feature - TenantOperator 3. Groups - Incoming Call Distribution Group - Group Setting Supervisor Extension 4. Groups - Incoming Call Distribution Group - MemberExtension No. 5. Groups - Idle Extension Hunting GroupMember Extension 6. Groups - Voice (DTMF) Group - Group InformationExtension Number of the SLT Port Connected to VM 7. Extension - Wired Extension/Portable Station - Extension Settings Transfer Recall Destination 8. Optional Device - DISA - Message Setting1 Digit AA Destination 9. Feature - Speed Dial & Caller ID - Main TableCLI Destination 10. CO & Incoming Call - DIL Table & Port SettingDIL Destination 11. CO & Incoming Call - DDI/DID TableDDI/DID Destination 12. CO & Incoming Call - MSN TableMSN Destination 13. Maintenance - MiscellaneousLocal Alarm Display Extension The following extension assignment logical check function is deleted from the V1.1 PC-Soft. In programming an extension number that does not exist, the system will now accept. Logical Check -1

58 Confidential58 What happens? - TDA100/200 Ver TDA100/200 Ver Open the PC maintenance tool and go to 2.System Operator then 2. PBX Operator 2- Click “Apply” 1- Open the PC maintenance 2- Go to 2.System Operator 2. PBX Operator 3- Click “Apply” Dealer does not know what is wrong! Nothing happens. Please remember, when programming extension numbers that do not exist, that the system will now accept the entry. Logical Check -2

59 Confidential59 If we program a non-existing number ?? 1. PBX-Operator  OUS mode Extension. 2. Tenant Operator  OUS mode Extension. 3. Supervisor Extension  No Supervisor Extension 4. ICD Group Member  The TDA skips this extension. 5. Idle Extension Hunting Group Member  The TDA skips this extension. 6. VM (DTMF) Group  VM function does not work. 7. Transfer Recall Destination  The transfer recall goes back to the transferring Extension Digit AA Destination  The TDA sends the re-order tone. 9. CLI/DIL/DDI/DID/MSN Destination  The TDA checks the following… 10. Local Alarm Display Extension  No Alarm Extension. - Re-order tone - Re-routed to operator Logical Check -3

60 Confidential60 Handover can be made during Conference Call. - Both of 2.4GHz model and DECT model - No programming required PS Hand-over during Conference Call

61 Confidential61 A “Fault” extension card can be used for walking extensions. Insert and remove a card, the non connected extensions can be used for walking extensions. DHLC-824 extensions SLC-88 extensions DLC-8/SLC1616 extensions DLC-1632 extensions Walking Extension from Fault Extension -1

62 Confidential62 Ext 201 Ext 233 Part-time worker - A8:00-12:00 Ext 234 Part-time worker - B 12:00-16:00 Ext 235 Part-time worker - C16:00-20:00 Ext 236 Part-time worker - D20:00-8:00 One existing extension can be shared to several users with different extension number. What is benefit ? What is Walking Extension access code? *727 + Extension number + PIN Walking Extension from Fault Extension -2

63 Confidential63 To Start TDA100/200 V1.1 - PC Maintenance Console Compatibility - Data Conversion - Upgrade PBX

64 Confidential64 TDA100/200 Ver.1.1 PC maintenance console can maintain TDA100/200 Ver.1.0 PBX, too. Initial screen When we access TDA100/200 Ver.1.0 Automatically PC Maintenance Console Compatibility

65 Confidential65 Data Conversion DSYS-1.1 PC maintenance console provides a data convert function. (DSYS Ver.1.0 to DSYS Ver.1.1) 1- Open the PC Maintenance console and open the saved DSYS (Ver 1.0). DSYS Enter new file name and click “Save” 2- Click DSYS 1.1

66 Confidential66 Upgrade PBX 1. Prepare following files - PMPR 1.1, DLNG0 1.1, DLNG DSYS Converted DSYS or New DSYS created by PC-Soft 2. Download above files to PBX 3. Reset PBX by command - V or later --- Please select PMPR_SUB, DSYS_SUB, then reset - Before V Please reset without any care. Select 4.Connect PC-Soft again and download other files as PC-Soft’s dialog box saying. 5.If PC-Soft require reset, reset PBX again, then you can finish upgrading.

67 Confidential67 Thank you very much !


Download ppt "Confidential1 Panasonic Communications Co., Ltd. Network Business Company Edition 1.3 07 Jul., 2004 Enhanced Items KX-TDA200/100 System (Ver.1.1)"

Similar presentations


Ads by Google