1. Pilot Walktour Pack Operation Guide V3.2

2. Contents 1 2 3 4 5 Overview Test Procedure Outdoor Test Indoor Test
Data Management 2 1 3 5 4
Overview

3. Overview
Pilot Walktour Pack, a solution that is based on the combination of iPad and smart phones, is a portable wireless network benchmarking tool for indoor and outdoor data collection activities. It measures network performance and services quality from a user’s perspective. Data interaction is achieved through connecting the iPad and smart phones via Wi-Fi. The iPad is used as the control device, to manage one or more handsets during test measurement. The handsets perform data or voice tests according to the test plan distributed from the iPad and then uploads the test data back to the iPad for display.

4. Pilot Walktour Pack Case (WiFi+ interaction system + power control)
System Architecture
Controller
Connection through WiFi and USB cables
Pilot Walktour Pack Case (WiFi+ interaction system + power control)
Control Interaction
Data Interaction
iOS: connection through WiFi
Android: connection through USB
Connection through WiFi and USB cable

5. Test Procedure 1 2 3 4 5 6 Connect Pilot Walktour Pack Case
System Settings
Automatically Detect Devices and Group
Configure Test Task
Deliver Test Task 2 1 3 5 4
Start Tests 6
Connect Pilot Walktour Pack Case

6. Connect Pilot Walktour Pack Case
Wi-Fi: PhoneBox_XXX (where XXX indicates a string like "181")
Password:
Turn on the power of the Pilot Walktour Pack Case.
Connect iPad to the WiFi hotspot of the Pilot Walktour Pack Case.
Connect all test devices to the Pilot Walktour Pack Case.
iOS based devices: Connect to the WiFi hotspot of the Pilot Walktour Pack Case
Android based devices: Connect to the USB port of to the Pilot Walktour Pack Case.
Start Pilot Walktour Pack.
Start Pilot Walktour, and tap Multi-Test.

7. Introduction to the USB Interface of Pilot Walktour Pack Case
USB interface and power charging interface
Power charging interface

8. System Settings
After logging in to Pilot Walktour Pack, tap Settings to configure the system.
Set the correct server information and select a data transmission mode.
Select a data partitioning mode and set a threshold value. The default data partitioning mode is By Size and the value is 6 M.
Enable Daylight Saving Time as required.
Tap Version to select a version as required (options: For China Unicom User, For General User).

9. Automatically Detect Devices and Group1 2 3 4
After connecting iPad and mobile phones to the system, enter the home page. Tap New Project, and Pilot Walktour Pack will automatically detect devices.
Drag detected devices into different test groups as required, and then tap Save.

10. Configure Test Tasks Tap Edit Task to configure test tasks.
Select a test service and configure information as required.
Tap Save.
Select a test service
Edit and save the test task

11. Deliver Test Tasks
After editing test tasks, tap the button shown as in the figure to deliver test tasks.
Tap this button to deliver test tasks.

12. Start Test——Outdoor Test
After delivering test tasks, tap the button to start test.
Select Outdoor.
Enter required test information.
Tap OK.

13. Viewing Test Information
During test, users may tap a group to view corresponding information, including test routes, messages, and parameters. 1 2 3
Test Routes on the Map
Messages
Parameters

14. Start Test—Indoor Test
After delivering test tasks, tap the button to start test.
Select Indoor.
Enter required test information.
Tap OK.

15. Pin Point on the Map During test, tap a Group, and select a map.
Tap Mark and then move your finger onto the map as required.
Tap Undo Mark to cancel the last pinning points. Tap Clear All to clear all points. Tap Clear Map to clear the map.

16. Viewing Test Information
During test, users may tap a group to view corresponding information, including messages, and parameters.

17. Data Management Tap the RCU icon to enter the data management window.
Outdoor test data files and indoor test data files are categorized individually.
Users may tap Sort, Delete, Upload, and Sycn to sort, delete, upload, and synchronize data files respectively
Note: Users cannot conduct any operation on data files during test.