Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby L0 Electronics Installation  System Electronics Overview u Low Voltage u High Voltage u RTD-Carbon Fiber Temperature Monitoring u Readout  Prep Work Summary  Person-power, Schedule 1

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby System Electronics  The L0 Upgrade electronics consist of 4 systems. u Isolated Low Voltage Power Supply s Wiener PS-Filter-Fuse Panel-PS Interlock-CAN bus interface u High Voltage Power Supply s HV crate-Fanout Chassis (2 units) u RTD Temperature Monitoring s RTD-Flex-(32AWG-filter-26AWG)-Controller u Readout s Junction Card-Twisted pair cable-Adapter Card 2

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby Isolated Low Voltage System 3

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby Components installed  Installed and Tested u 2 Fuse Panels u East and West Side u Quadrant Specific Collision Hall-Cathedral Area  Installed and Tested u Wiener Power Supply u Safety Interlock 2 nd Floor Movable Counting House 4

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby LV Power Supply Filter Response 40V  pedestal  total noise  10  diff. noise  10 without ferritewith ferrite channel ADC counts  5 turns on ferrite core of power cable reduced noise to cts.  Prototype filter design ready to test.  Preliminary 200 gauss magnetic field tests show minimal effect on filter action. 5

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby Filter location  Install below fuse panel in cathedral area.  2 quadrants per card. 6

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby  Prep work remaining u Test filter at 100% test stand. u Enter operating parameters in EPICS database. u Test CAN bus interface via GUI in Control Room.  Work remaining in Collision Hall u Install filter in cathedral. u Cable Plant: s 12 twisted pair 10AWG cables –fuse panel  filter –filter  gauge change panels on horseshoe s 12 twisted pair 22AWG cables –gauge change panels  Adapter Card LV PS work remaining 7

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby High Voltage System  1st crate (L0) with 48 pods and power supply tested and installed in the 100% test stand at SiDet. u Pods modified to accommodate lower current.  2 nd 48 pod crate (SMT expansion) load tested and ready for installation.  Prep work: u Order HV cables within next couple of weeks.  Work remaining in Movable Counting House. u Install 2 HV crates-1 st from SiDet, 2 nd in house. u Install 2 Fanout chassis for L0. u Install 96 SHV cables from HV pods to Fanout chassis. u Remapping of Inner H-disk channels. u Distribute additional 48 channels in Fanout chassis.  Work remaining in Collision Hall: u None 8

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby RTD system  Monitors carbon fiber structure temperature.  Testing at SiDet has uncovered noise coupling into the readout from RTD flex circuits.  32 AWG cable shielding tied to isolated ground at AC removed noise conductor Hirose L0 Isolated GND 36 conductor x8 9

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby RTD System  Prep work u Test filter card-shielding scheme. s How much lead resistance can Controller tolerate? –Latest studies show the Controller can handle 3K Ohm per lead. Filter design for 60dB attenuation at 1kHz has 1.3K Ohm per lead. s Current design (RCRCR) has filter located on horseshoe. –Filter:Capacitors need a connection to detector ground in the vicinity of Adapter Card. 1 location per quadrant required. Location has been defined. –Shield:Requires a connection to LV isolated ground. By positioning filter card in close proximity to gauge change panel, connection is easy. Location has been defined. 10

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby DAQ Mapping  Positions for the temperature monitoring gauge change panels, LV gauge change panels, and Adapter Cards were determined based on the existing DAQ cable map.  Every effort has been made to minimize the number of cable moves required to integrate L0 into the current system.  Since the Outer and Inner H-disk low mass cables are combined on one old AC, it is necessary to move half of the Inner H-disk low mass cables (48). The open channels will be used for L0. 11

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby SE_1 Mapping IB Sequencer VRB 12

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby SouthEast S1: 10,11 S2: 23,24 S6: 76,77 AC LV AWG  Sector 1 Low Mass Moves Open Positions for Sector 1 10C2 to 02C1 10, 11, 12, 18 11C2 to 03C1 12C2 to 04C1 18C2 to 09C1 Sector 2 Low Mass MovesOpen Positions for Sector 2 23C2 to 15C1 23, 24, 25, 31 24C2 to 16C1 25C2 to 17C1 31C2 to 22C1 Sector 6 Low Mass MovesOpen Positions for Sector 6 76C2 to 05C1 76, 77, 78, 79 77C2 to 69C1 78C2 to 70C1 79C2 to 71C1 RTD Filter 13

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby Readout-Adapter Card  Work in Collision Hall u Remove 24 old ACs and standoffs. u Install 12 new ACs and mounts – 3 per quadrant. u Route 48 twisted pair cables from Adapter Card mounting ring (horseshoe) to Junction Card ring. u Connect Isolated LV power supply cable. Adapter Card Installed on Horseshoe 14 Digital jumper cable  Junction Card  Twisted Pair  Adapter Card

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby Readout-Junction Card Junction Card and Twisted pair cable 6 per ring — 12 per end Junction Card Mounting Ring 2 rings per end 15 Digital jumper cable  Junction Card  Twisted Pair  Adapter Card

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby Readout-Junction Card  Work in Collision Hall u Connect digital jumper cable from detector to Junction card. u Mount Junction card. u Test channel with laptop and calibration pulse. s Confirms HV and LV are correct, the hybrid can be downloaded, and a calibration pulse is read out through entire chain. u Complete first tier ring of 6 cards on each end. u Install 6 more cards on second tier mounting ring. u Test in same fashion. 16

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby Silicon Track Trigger  Layer Zero utilizes VRB slots previously used by H-disks.  H-disks were not used in the STT trigger.  To integrate Layer Zero into the trigger, SEQ fibers need to be moved from the associated VRB crates to the splitters mounted on the wall in the 2 nd floor movable counting house (MCH2).  Work in MCH2 u Reroute 2 fibers/VRB crate (24 total) to splitter. u Install 2 fibers/splitter (24 total) to VRB crates. 17

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby Prep Work Summary  LV system u Filter designed. Ready for testing.  HV system u Install RunIIa SMT expansion crate. u Order SHV cables for L0 and expansion crate.  RTD system u Filter designed. Quotes requested.  Readout u SEQ-splitter fiber plant. u Fibers/splitters in house. Need labels. 18

Director’s Review of RunIIb Dzero Upgrade Installation Linda Bagby Time and Personnel 19