Bolt Die Cutting threads on bolts and rods.
Bolt Die Stock Holder for bolt tie.
Bolt Tap Cutting inside threads.
Tap Wrench Holding bolt tap.
Phillip’s Screwdriver Turning phillips heads screws.
Compass Drawing circles.
Slip Joint Pliers Adjust for holding various size material.
Chalk Line Reel Making straight lines.
Chipping Hammer Removing slag from welds.
Bent Nose Pliers Reaching obstructive or awkward places.
Combination Wrench Turning hex and square nuts and bolts.
Box End Wrench Turning hex head nuts and bolts.
Adjustable Wrench Turning various size nuts and bolts.
Circuit Breaker Protection from overload in electrical circuits.
Drift Punch Aligning holes.
Cold Chisel Cutting metal.
Brick Jointer Smoothing and designing masonry joints.
Toggle Bolt Anchoring into a hollow space.
Open End Wrench Turning square head nuts and bolts.
Countersink Flaring top of hole for recessing head for flathead screw or bolt.
Soil Tube Obtaining soil for testing.
Reversible Ratchet Reverse rotation of socket turning.
Regular Socket General purpose socket for turning nuts and bolts.
Deep Socket Turning nuts and bolts in depressed areas.
Keyhole saw Sheet rock Key holes in wood
Allen Wrench Turning hex head socket screws.
Nail Hammer Driving nails. Usually 16 oz. Also called Bent Claw Hammer
Aviation Snips Cutting sheet metal.
Bar Clamp Clamping large sections of wood together.
Bolt Cutters Cutting bolts & steel rods.
Groove Joint Pliers Gripping when greater pressure is needed. Also called Channel Locks
Long Nose Pliers Reaching into recessed areas.
Ball Pein Hammer Hammering metal.
Lopping Shears Cutting large braches when pruning shrubbery.
Vise Grip Pliers For extra firm gripping.
Brick Trowel Placing and spreading mortar.
Butt Hinge Hinge for narrow fencing.
C Clamp Clamping two or more pieces of metal together.
Center Punch Starting holes in metal.
Nail Set Countersinking nail heads.
Chain Saw File Sharpening chain saw file.
Circular Carbide Saw Blade Blade used on portable electric saw.
Common Nail Nailing boards together where holding power is desired.
Compass Saw Cutting wood in close places.
Hack Saw Sawing metal.
Coping Saw Cutting curves and irregular cuts.
Cordless Drill Drilling holes with a tool that uses a battery pack.
Level Leveling and plumbing.
Hand Saw Cutting wood Very Common
Back Saw More precise cuts Goes well with Miter box
Combination Square Determining 45 o and 90 o angles.
Combination Oil Stone For sharpening and honing cutting tools.
Finishing Nail Nailing boards where head will not be noticed.
Flathead Wood Screw Fastening wood to wood where a flat surface is required.
End Cutting Nippers Cutting ends of wire, nails and small bolts.
Hole Saw Cuts door holes
Diagonal Cutting Pliers Surface and diagonal wire cutting.
Duplex Receptacle To plug electrical units.
Extension Extends reach of socket.
Universal Joint Holding socket for angle turning.
Universal Socket/ Flex socket Socket for angle turning.
Glass Cutter Cutting glass.
Lag Screw Screw used where great pressure to turn is required.
Expansion Shield Anchoring a lag screw into concrete, brick or block.
Framing Square Squaring cut corners and laying out stairs and rafters.
Pruning Saw Sawing limbs from shrubbery and trees.
Hand Screw Clamp Clamping wood together. Lightweight
Fence Pliers Building and repair of wire fences.
File Card Cleaning cutting grooves of file.
Half Hatchet Cutting and fitting wood.
Bulb Planter Planting and transplanting bulbs.
Bush Axe Cutting bushes and under growth.
Side Cutting Pliers Holding and/or cutting wire.
Castrator Tool for sterilizing male animals.
Mason Hammer Chipping and shaping masonry material.
Concrete Finishing Trowel Smoothing concrete.
Cutting Torch Cutting metal with heat.
Grafting Tool Preparing woody parts for grafting.
Dehorner Removing horns from cattle.
Hedge Shears Trimming and shaping hedge.
Grease Gun Lubricating through grease fitting.
Eye Bolt Bolt used to attach wire onto.
Fence Staple For nailing up fence.
Drill Press Vise Holding stock while drilling.