TCP/IP Protocol Suite 1 Chapter 8 Upon completion you will be able to: ARP and RARP Understand the need for ARP Understand the cases in which ARP is used Understand the components and interactions in an ARP package Understand the need for RARP Objectives

TCP/IP Protocol Suite 2 Figure 7.1 ARP and RARP

TCP/IP Protocol Suite 3 Figure 7.2 Position of ARP and RARP in TCP/IP protocol suite

TCP/IP Protocol Suite ARP ARP associates an IP address with its physical address. On a typical physical network, such as a LAN, each device on a link is identified by a physical or station address that is usually imprinted on the NIC. The topics discussed in this section include: Packet Format EncapsulationOperation ARP over ATM Proxy ARP

TCP/IP Protocol Suite 5 Figure 7.3 ARP operation

TCP/IP Protocol Suite 6 Figure 7.4 ARP packet

TCP/IP Protocol Suite 7 Figure 7.5 Encapsulation of ARP packet

TCP/IP Protocol Suite 8 Figure 7.6 Four cases using ARP

TCP/IP Protocol Suite 9 An ARP request is broadcast; an ARP reply is unicast. Note:

TCP/IP Protocol Suite 10 A host with IP address and physical address B2:34:55:10:22:10 has a packet to send to another host with IP address and physical address A4:6E:F4:59:83:AB (which is unknown to the first host). The two hosts are on the same Ethernet network. Show the ARP request and reply packets encapsulated in Ethernet frames. Example 1 See Next Slide

TCP/IP Protocol Suite 11 Solution Figure 7.7 shows the ARP request and reply packets. Note that the ARP data field in this case is 28 bytes, and that the individual addresses do not fit in the 4- byte boundary. That is why we do not show the regular 4-byte boundaries for these addresses. Also note that the IP addresses are shown in hexadecimal. For information on binary or hexadecimal notation see Appendix B. Example 1 (Continued) See Next Slide

TCP/IP Protocol Suite 12 Figure 7.7 Example 1

TCP/IP Protocol Suite 13 Figure 7.8 Proxy ARP

ATMARP When IP packet are moving through an ATM WAN,a mechanism protocol is needed to find the physical address of exiting-point router in the ATM WAN given the IP address of router. The format of an ATMARP packet,which is similer to the ARP packet. TCP/IP Protocol Suite 14

TCP/IP Protocol Suite 15 Figure 3.24 Architecture of an ATM network

ATMARP Operation There are two methods to connect two routers on an ATM network: 1.PVC(Permanent Virtual Circuit) 2.SVC(Switched Virtual Circuit) 1. PVC Connection It is established between two end points by the network Providers. The VPI and VCI are defined for permanent connections and the values are entered in a table for each switch. The inverse request message and inverse reply message Can be used for the binding. There is no need for an ATMARP server. TCP/IP Protocol Suite 16

SVC Connection In svc connection,each time a router wants to make a connection with another router (or any computer), a new virtual circuit must be established. To map the ip addresses to physical addresses Each router runs a client ATMARP program, but only one computer runs an ATMARP server program. TCP/IP Protocol Suite 17

TCP/IP Protocol Suite ARP PACKAGE In this section, we give an example of a simplified ARP software package to show the components and the relationships between the components. This ARP package involves five modules: a cache table, queues, an output module, an input module, and a cache-control module. The topics discussed in this section include: Cache Table Queues Output Module Input Module Cache-Control Module

TCP/IP Protocol Suite 19 Figure 7.9 ARP components

ARP_Output_Module () { Sleep until an IP packet is received from IP software. Check cache table for an entry corresponding to the destination of IP packet. If(entry is found) { If (the state is RESOLVED) { Extract the value of the hardware address from the entry. Send the packet and the hardware address to data link layer. return } TCP/IP Protocol Suite 20

TCP/IP Protocol Suite 21 If (the state is PENDING) { Enqueue the packet to the corresponding queue. Return. } If(entry is not found) { Create a cache entry with state set to pending & attempts set to 1. Create a queue. Enqueue the packet. Send an ARP request. Return. }

ARP_Input_Module() { Sleep until an ARP packet (request or reply) arrives. Check the cache table to find the corresponding entry. If(found) { Update the entry. If(the state is PENDING) { While (the queue is not empty) { Dequeue one packet. Send the packet and the hardware address. } TCP/IP Protocol Suite 22

If (not found) { Create an entry. Add the entry to the table. } If (the packet is a request) { Send an ARP reply } Return } TCP/IP Protocol Suite 23

ARP_Cache_Control_Module { Sleep until the periodic timer matures Repeat for every entry in the cache table { If (the state is FREE) { Continue } If (the state is PENDING) { Increments the value of attempts by 1 If(attempts greater then maximum) { Change the state to FREE Destroy the corresponding queue } TCP/IP Protocol Suite 24

Else { Send an ARP request } Continue } If (the state is RESOLVED) { Decrement the value of time-out If (time-out less than or equal 0) { Change the state to FREE Destroy the corresponding queue } TCP/IP Protocol Suite 25

TCP/IP Protocol Suite 26 Table 7.1 Original cache table used for examples

TCP/IP Protocol Suite 27 The ARP output module receives an IP datagram (from the IP layer) with the destination address It checks the cache table and finds that an entry exists for this destination with the RESOLVED state (R in the table). It extracts the hardware address, which is ACAE32, and sends the packet and the address to the data link layer for transmission. The cache table remains the same. Example 2

TCP/IP Protocol Suite 28 Twenty seconds later, the ARP output module receives an IP datagram (from the IP layer) with the destination address It checks the cache table and does not find this destination in the table. The module adds an entry to the table with the state PENDING and the Attempt value 1. It creates a new queue for this destination and enqueues the packet. It then sends an ARP request to the data link layer for this destination. The new cache table is shown in Table 7.2. Example 3 See Next Slide

TCP/IP Protocol Suite 29 Table 7.2 Updated cache table for Example 3

TCP/IP Protocol Suite 30 Fifteen seconds later, the ARP input module receives an ARP packet with target protocol (IP) address The module checks the table and finds this address. It changes the state of the entry to RESOLVED and sets the time-out value to 900. The module then adds the target hardware address (E ACA) to the entry. Now it accesses queue 18 and sends all the packets in this queue, one by one, to the data link layer. The new cache table is shown in Table 7.3. Example 4 See Next Slide

TCP/IP Protocol Suite 31 Table 7.3 Updated cache table for Example 4

TCP/IP Protocol Suite 32 Twenty-five seconds later, the cache-control module updates every entry. The time-out values for the first three resolved entries are decremented by 60. The time-out value for the last resolved entry is decremented by 25. The state of the next-to-the last entry is changed to FREE because the time-out is zero. For each of the three pending entries, the value of the attempts Example 5 See Next Slide

TCP/IP Protocol Suite 33 Table 7.4 Updated cache table for Example 5

TCP/IP Protocol Suite RARP RARP finds the logical address for a machine that only knows its physical address. The topics discussed in this section include: Packet Format Encapsulation RARP Server Alternative Solutions to RARP

TCP/IP Protocol Suite 35 The RARP request packets are broadcast; the RARP reply packets are unicast. Note:

TCP/IP Protocol Suite 36 Figure 7.10 RARP operation

TCP/IP Protocol Suite 37 Figure 7.11 RARP packet

TCP/IP Protocol Suite 38 Figure 7.12 Encapsulation of RARP packet