Evolution Industries, Inc. Updated October 1, 2010

Keep work area clean, organized, and well-lighted Immediately clean up spills Always use appropriate safety gear Dress appropriately for lab work NEVER use equipment when under the influence of drugs/alcohol Stay alert. Pay close attention when using machinery at all times Keep all guards operational and in place at all times Ensure that work piece is free from nuts, staples, or other objects that could become projectiles Follow guidelines for safe use of each individual machine at all times Consult manual when performing service or maintenance on machines Do not use machines for jobs for which they were not intended Keep children and pets away from work areas.

 Materials including scrap and debris should be contained to prevent objects from falling, becoming projectiles, or creating a dusty atmosphere  Floor of the work area is free from spills or accumulation of debris that could constitute a slipping or tripping accident  Storage area is free of accumulation of materials that constitute hazards from fire, fumes, or pest infestation  An unobstructed 3 foot aisle is maintained between machines

 Eye protection is worn at all times.  Ear plugs or other hearing protection can be worn while loud machinery or air compressor is in use.  Heavy duty gloves can be worn when working with belt sander or grinder.  Protective sleeves and heat-resistant gloves are worn when working with the ovens.  Closed toe shoes, preferable leather with slip-resistant soles, are worn in lab areas.  Long sleeves, long pants, and lab coats can be worn to protect exposed skin from dust.

 Loose clothing can NOT be worn while operating machinery or working near machinery. This includes baggy clothing, neckties, drawstrings, hoods, etc.  Long sleeves must be rolled up tightly above the elbows.  Loose neck wear and jewelry is to be taken off while operating machinery or working near machinery.  Long or loose hair must be contained in a cap or scarf.  Closed toe shoes, preferable leather with slip-resistant soles, must be worn in lab areas.

 Make sure the power is switched to “off” before plugging machinery to the wall.  Keep all guards operational and in place at all times.  Check for damaged parts and replace worn/damaged parts with identical replacement parts immediately.  Avoid overreaching. Maintain stability and balance at all times.  Never walk away from a spinning or running machine until it stops completely.  Do NOT use extension cords as a permanent power source.  Do NOT locate machinery so that the operator must stand in an aisle or high traffic area.  Ensure that machinery is installed to prevent unintentional tipping or movement.  Always refer to machine’s manual when servicing or ordering parts.

 Remove all adjusting wrenches from the band saw before turning it on.  Before using, ensure that the band saw blade is not bent or cracked.  Keep work piece flat and secure on the table.  Hands should not be in the same plane as the saw blade. Keep hands to the side of the stock, at least a few inches away from the blade.

 Do not force material into the blade saw while cutting. Apply moderate pressure, allowing the saw blade to cut without being forced.  Never attempt to remove debris stuck in moving parts until machine is turned off and unplugged.  Never back work piece away from the blade if it becomes bound or stuck.  During use the saw blade will become hot. Allow blade to cool before touching.  Keep hands and fingers away from band saw blade during use.  Always disconnect the band saw from its power source before performing service.

 Replace cracked, broken, or excessively worn grinding wheel immediately.  Always remove all adjustment keys and wrenches from the bench grinder before starting.  Wear heavy-duty work gloves and other necessary safety gear while operating the grinder.  Stand to one side when turning the power on. Do not use a wheel that vibrates.  Keep fingers and hands as far away from rotating grinding wheel as possible.

 Keep a firm grip on the work piece with both hands.  Bring the work piece into contact with the wheel slowly and smoothly.  Move the work piece back and forth across the face of the wheel only. This prevents ruts or grooves from forming.  Handle object being ground with care, since it will become hot during grinding.  Always disconnect the grinder from its power source before servicing. Do not carry or pull the grinder by its power cord.

 Keep a firm grip on the work piece with both hands.  Allow sander to reach full speed before engaging the work piece  Bring the work piece into contact with the wheel slowly and smoothly.  Move the work piece back and forth across the face of the sander only. This prevents ruts or grooves from forming.  Do not place hands near sander during operation. Never put hands or fingers in between sander and work piece.  Handle object being sanded with care, since it will become hot during grinding.

 Do not use the sander as a replacement for a band saw or other cutting tool. It is designed for finish work only.  Replace sanding sleeves when worn or torn.  Always disconnect the sander from its power source before servicing.

 Use only recommended, properly installed accessories  Keep hands and loose clothing away from rotating tool and shaft  Keep a firm grip on stock with both hands.  Avoid placing excess pressure on the carver tool or shaft.

 Do not use abrasive belts that are excessively worn.  Use of leather gloves may be effective in protecting hands and fingers.  Stand to one side when turning the power on. Do not use a wheel that vibrates.  Allow belt to reach full speed before using.  Keep body parts and loose clothing away from moving parts.  Hold work pieces firmly in both hands.

 Never use unnecessary pressure on the stock piece or tool.  Bring the work piece into contact with the wheel slowly and smoothly.  Move the work piece back and forth across the face of the wheel only. This prevents ruts or grooves from forming.  Handle object being ground with care, since it will become hot during grinding.  Always turn off and unplug equipment before performing any adjustments or service.

 Secure work piece to the table. Do NOT try to hand-hold the work piece.  Keep clothing and hands away from rotating drill bit.  Work pieces and drill bit can become hot due to friction. Be careful handling after use.  Clear debris and scraps after use.

 Avoid moving parts during operation. Keep hands and fingers away from all moving parts.  Do not compress springs.  Do not press items that could disengage and cause a potential hazard.  Do not operate jack beyond rated capacity.

 ws.html ws.html  /production_sanders.html /production_sanders.html  ss.html ss.html  