CONVERTER SETTING FOR TCP/IP COMMUNICATION BETWEEN CONTROLLER & PC (OPERATING SW) ► IDTECK Home ► e-Training Center ► Catalog ► Manual ► Installation Guide ► Troubleshooting ► Purchase Order

TCP/IP COMMUNICATION Through INTERNAL TCP/IP MODULE (IIM7100A) -1 Direct Connection Mode - TCP/IP module Insertion 1 (Factory Setting) Make sure that the arrow direction of module and Controller board must be the same. (applicable to version 3.0.0 or higher) - Change Jumper Setting for TCP/IP communication Change Jumpers RS422(Default) TCP/IP RJ-45 Connector Make sure that the Jumpers (JP1 ~ JP4) must be set to the right position. Connect LAN cable between RJ45 Jack of Controller. - Connects to the network such as hubs or router : Use Direct LAN Cable - Connects to the PC directly : Use Cross LAN Cable ► Catalog ► Manual ► Installation Guide ► Troubleshooting Copyright (c) 2008 IDTECK. All rights reserved. ► Purchase Order

TCP/IP COMMUNICATION Through INTERNAL TCP/IP MODULE (IIM7100A) - 2 Bypass Connection Mode - Change Jumper Setting and Wiring for TCP/IP and slave RS422 Communication Connect LAN cable between RJ45 Jack of Controller #1 - Connects to the network such as hubs or router : Use Direct LAN Cable - Connects to the PC directly : Use Cross LAN Cable Cross-connect RS422 wires between Controller #1 and Controller #2. (①) Direct-connect RS422 wires between Controller #2 and Controller #3~#n.(②) Change Jumper Setting - Controller #1 : Make sure that the Jumpers(JP1~JP4) must be set to the right position. - Controller #2~#n : Make sure that the Jumpers(JP1~JP4) must be set to the left position. ► Catalog ► Manual ► Installation Guide ► Troubleshooting Copyright (c) 2008 IDTECK. All rights reserved. ► Purchase Order

INTERNAL TCP/IP MODULE SETUP (IIM7100A) Software Setting After running converter setting program and press Search Icon, it will search TCP/IP Module connected to your network. Network Tab ► Catalog ► Manual ► Installation Guide ► Troubleshooting Copyright (c) 2008 IDTECK. All rights reserved. ► Purchase Order

TCP/IP COMMUNICATION THROUGH EXTERNAL TCP/IP MODULE (ILAN422 & 485)

TCP/IP COMMUNICATION Through EXTERNAL TCP/IP CONVERTER RS232 to TCP/IP Conversion 505R, iCON100, Finger007, Finger006, FGR006, etc… (built- in RS232 module) RS232 LAN, WAN, INTERNET 15m TCP/IP Converter RS485 to TCP/IP Conversion RFL200C, 505R, iCON100, Finger007, Finger006, FGR006, FGR007, etc… (built –in RS485, RS422 module) 15m RS485 LAN, WAN, INTERNET TCP/IP Converter RS422 to TCP/IP Conversion 505R, iCON100, Finger007, Finger006, FGR006, FGR007, etc… ( built –in RS422 module ) RS422 LAN, WAN, INTERNET TCP/IP Converter ► Catalog ► Manual ► Installation Guide ► Troubleshooting Copyright (c) 2008 IDTECK. All rights reserved. ► Purchase Order

Controller ILAN422/ILAN485 (9Pin D-SUB Connector) RXD Pin 3(TXD) TXD EXTERNAL TCP/IP CONVERTER SETUP (ILAN422/ILAN485) RS232 to TCP/IP Conversion ILAN422 ILAN485 Controller ILAN422/ILAN485 (9Pin D-SUB Connector) RXD Pin 3(TXD) TXD Pin 2(RXD) GND Pin 5(GND) ► Catalog ► Manual ► Installation Guide ► Troubleshooting Copyright (c) 2008 IDTECK. All rights reserved. ► Purchase Order

Controller ILAN485 (Terminal Block) RS485 Product RXD+ (RS485 A) 485 + EXTERNAL TCP/IP CONVERTER SETUP (ILAN485) RS485 to TCP/IP Conversion Controller ILAN485 (Terminal Block) RS485 Product RXD+ (RS485 A) 485 + RXD– (RS485 B) 485 - RS422 Product RX+, TX+ RX- , TX- ► Catalog ► Manual ► Installation Guide ► Troubleshooting Copyright (c) 2008 IDTECK. All rights reserved. ► Purchase Order

Controller ILAN422 (Terminal Block) RX+ T+ RX- T- TX+ R+ TX- R- EXTERNAL TCP/IP CONVERTER SETUP (ILAN422) - 1 RS422 to TCP/IP Conversion Controller ILAN422 (Terminal Block) RX+ T+ RX- T- TX+ R+ TX- R- CROSS CONNECTION ► Catalog ► Manual ► Installation Guide ► Troubleshooting Copyright (c) 2008 IDTECK. All rights reserved. ► Purchase Order

EXTERNAL TCP/IP CONVERTER SETUP (ILAN422) - 2 Software Setting After the program is opened, click the Refresh button. Then, the information of all the LAN converters connected to the same network will be displayed as in the picture below. Click the LAN converter that you’d like to configure, then the IP Address and SubMask fields will be automatically filled. User Name：admin Password：admin ► Catalog ► Manual ► Installation Guide ► Troubleshooting Copyright (c) 2008 IDTECK. All rights reserved. ► Purchase Order

techsupport@idteck.com For more information, Contact us at Thank you. Copyright (c) 2008 IDTECK. All rights reserved.