VESTAS SQUIRTER DEMO Applied Bolting Technology 1413 Rockingham Road Bellows Falls, VT USA 05101 Squirters are Patented US Patent No 5,931,618.

Slides:



Advertisements
Similar presentations
RP4AN 21/2 – 6. Modification Overview Production of the RP4AN series began in Production of the RP4AN series began in The 4AN indicates an.
Advertisements

Untightening torque Can we use the untightening / tightenigng torque ratio to estimate the efficiency of HEICO-LOCK ?
Mechanical Division Standard Hand Tools. Topics Design T-Square Drafting Triangle Fabrication Hacksaw Cordless Drill File Sandpaper & Steel Wool Assembly.
Torque Tension Rahul Harikrishnan, Leslie Tuan, Grant Guenter, Ransom Cutshall, Mattea Cavagnaro Bernard Roberts, Lucas Caretta, Rebecca Ahern, Kaleb Richardson,
Instructions for making plunger fork tool. Drawing for the trigger assembly.
BumperBot uses two contact switches to go through a labyrinth. Bumper.
Installation Procedures
RockOn! Canister Integration RockOn! 2009.
AS100 Installation Air Tight Solutions The only solution AS100 Valve Stem Adapter Small O-ringLarge O-ring Standard Brass Valve Stem If you purchased your.
Instructions for Diaphragm Replacement Cat. Nos. 2052B-01, 2054B-01
Honda 450 Installation Manual.
Here is the broken line. Step 5: Break loose encasing seal. With bar in vice as show, hit with hammer to break loose. Usually 2 or 3 hits will break loose.
Rework Procedure for Wash Motor Pulley Change Model : Rosa & Rosa Plus Part Details & Tools required Sr NoPart DescriptionQtyTool used to replace old artworks.
Click on this image to open the full PDF document.
Fasteners Valerie Blakeslee, Pranav Harikrishnan, Hana Keller, Ben LaRoche, Kiana Peterson.
Flange-lok Installation Instructions Quick Installation Guide rev. DB.
Motor Leveling MECH 1200 Soft foot Condition: One or more of the mounting feet is not level with the others. Nuts loosen, vibration, misalignment Metal.
Laser Enclosure to Elevated Rail Assembly Wyman Gordon Forging Locator Original Revision: 2/14/2013.
Innovative Vehicle Technology Trailer Installation Procedures Automatic Brake Adjuster.
Honda Recon TRX-250 Installation Manual. STEP 1: Remove rear tires and install axle spacers. Use blue thread locker and tighten lugs to ATV specification:
UBC International Training Fund
Couplings Nizwa College of Technology.
LECTURE # 38.
Extended top hats installation instructions Included parts: Extended top hats (qty 2) Spring isolator bushing (qty 2) Energy Suspension top hat bushings.
CHANGING A FLAT TIRE WHY ME! I’M GOING TO BE LATE TO SCHOOL.
Pat Willoughby MIT/ABB Monday, September 11, 2000 X Z Y First Attempt - 30 to 60 minutes Following Attempts - 20 minutes Possibility for Wrist Damage Possibility.
Open manuals (aircraft alterations and repair) to page 7-9.
TF Coil Vacuum Vessel Wire Rope Tensioning Fixture 3 Per Segment Horizontal Stop 3 Per Segment Wood Block 2 Per Segment TFTR D&D FMEA REVIEW Vacuum Vessel.
The 2 reinforcement plates are made from a piece of 2” dia stainless tube. Read on for how this is done. 14.
ORTHOPEDIC SURGERY “The nuts and bolts of the operating room”
Power Of Pessimism 2 of 4. “The Power Of Pessimism: Defining the Nightmare”
Robert Fox, Ben Kellogg, Kasey Kitto, Jack Palmer Senior Project 2015: Lorenz Water Wheel.
TURBO REBUILD TURBO REBUILD. Step 1 Step 1: - Using the small pick or screwdriver, walk the tiny snap ring back into the groove on both the compressor.
Sign Structures Updates: Helpful Tips for Inspectors
Motor Mounting MECH1200 Foot Mount: Simple and common Tabs or feet that are attached at the four corners of the motor and attaches to a bedplate. Sometimes.
How to move your horn.. 1.This one is a shot of the horn with the acorn nut removed. STEP 1.
XR621 Drive Hose Update Kit. Removal Turn off Battery dis Drain hydraulic tank Remove both rubber lines under chassis and discard. Remove and discard.
3:00. 2:59 2:58 2:57 2:56 2:55 2:54 2:53 2:52.
PHYSICS – Forces 2 Moments
Model 466_666 Thorough and regular cleaning, in accordance with the working conditions, is recommended. The gauges are fitted with two bleed cap that.
Mechanical Joint Restraints
طراحی اتصالات Joints design. انواع وسائل ايجاد اتصال.
Assembly of steering.
Rear end assembly.
Instructions for Diaphragm Replacement Cat. Nos. 2052B-01, 2054B-01
Unit 26: Mechanical fasteners 1 Dr
Threads and Fasteners.
Fastener Facts Fastener Facts.
Easycliner (Motorized Version) Assembly Instruction
Fastener Facts Fastener Facts.
RPDA 4AN 21/2” – 6”.
Chapter 26: Mechanical fasteners 1
Top Fire Protection Services Ottawa available on Dubinskyconstruction
Tips Need to Consider When Organizing a College Event
BACK SOLUTION:
Emergency & Environmental Information
Unit 26: Mechanical fasteners 1 Dr
W201 3R hardboard Replacement Procedure.
ماجستير إدارة المعارض من بريطانيا
Sections, Assemblies & Exploded
CLICK TO START.
375DA 2½”-10”.
Educational Power Point by D&T Within Schools
CLICK TO START.
Emergency Information
Ultrasonic Bolt Tension Measurement
Replace Timing Belt 300 Hours.
Call Now : Click : -
Call Now : Click : -
Call Now : Click : -
Presentation transcript:

VESTAS SQUIRTER DEMO Applied Bolting Technology 1413 Rockingham Road Bellows Falls, VT USA Squirters are Patented US Patent No 5,931,618

VESTAS SQUIRTERS Problem – Develop a Direct Tension Indicating Squirter that enables achievement of 510 kN or a little more, virtually every time the M36 bolt is tightened. Solution – An M36 “Euro” Squirter DTI

VESTAS SQUIRTERS Assemble bolt, DTI, flat washer in Skidmore Tester

VESTAS SQUIRTERS Squirter, then flat washer, then nut on bolt

VESTAS SQUIRTERS Nut goes on last

VESTAS SQUIRTERS Tighten Until the squirt event says “stop!” Final tension does NOT depend on torque Click to activate movie ……

VESTAS SQUIRTERS The operator has stopped at the intended amount of squirted silicone, which is 528 kN!