. Load sensors conditioners – radiation tests Mateusz Sosin BE/ABP/SU RADWG,

Mateusz Sosin Research status of Low-Beta weighting system Summary Load sensors under Low-Beta quadrupoles – introduction Load sensors – signal conditioner Conditioner crate – components & radiation tests Questions Load sensors conditioners – radiation tests RADWG,

Mateusz Sosin Research status of Low-Beta weighting system Load sensors under Low-Beta quadrupoles Monitoring and adjustment system Monitoring alignment systems: Wire Positioning Systems – (WPS) and Hydrostatic Levelling Systems (HLS) are installed on top of the cryostat (precision of measurements of a few microns) Motorization of the Jacks according to 5 DOF 10 Vertical and 6 Radial Jacks per triplet Problem of loosing articulation point detected at february 2011 !!! Unexpected 0.8mm Q3R5 magnet jump during repositioning dangerous for installation Reported by D.Missiaen at LMC – Load sensor solution proposed Load sensors conditioners – radiation tests RADWG,

Mateusz Sosin Research status of Low-Beta weighting system Load sensors under Low-Beta quadrupoles Sensor Strain gauge – force washer type sensor Solution tested After market study - choosed German HBM MPZ Rad-hard qualified Constraints Very low possible space for sensor installation (ø70, h16 mm) High load (up to 15T) Radioactive area Load sensors conditioners – radiation tests RADWG,

Mateusz Sosin Research status of Low-Beta weighting system Load sensors under Low-Beta quadrupoles Configuration per one IP side: Installation for IP1,2,5,8 L&R Compatible with other SU instalations Load sensors conditioners – radiation tests RADWG, ? S.A.S.tested by A.Marin EDMS , FipADUC cards tested by R.Denz

Mateusz Sosin Research status of Low-Beta weighting system Load sensors – signal conditioner Suitable market accesible conditioners Expensive (0.6..1kCHF per channel) Additional cabling needed We have no influence for used components BE-ABP-SU conditioners (Analog Devices AD ’51 based) Cheap (0.1kCHF per channel) Suited for application Basic DSP abilities included AC/DC modes & cable compensation Load sensors conditioners – radiation tests RADWG,

Mateusz Sosin Research status of Low-Beta weighting system Load sensors – signal conditioner BE-ABP-SU prototype and HBM-AE301 conditioners checked at special test bench Similar noise with 270m cables High output signal stability for both conditioners Both solutions suitable for Low-Beta weighting system application Load sensors conditioners – radiation tests RADWG,

Mateusz Sosin Research status of Low-Beta weighting system SOLUTION: Basing on Survey Acquisition System electronics – create load sensors conditioning crate Use same part of electronics like in S.A.S. (FipADUC card) Add one PCB (12 channel input stage) in place of old S.A.S. input amplifiers board Load sensors – signal conditioner FIP ADUC CARD S.A.S. INPUT AMPLIFIERS BOARD CONN.TAPE FIP ADUC CARD LOAD SENSORS 12 CHANNEL INPUT STAGE PCB CONN.TAPE Advantages No additional cabling between conditioner and S.A.S. Small space in SU racks needed No big updates at FESA/PVSS level needed Load sensors conditioners – radiation tests RADWG,

Mateusz Sosin Research status of Low-Beta weighting system Conditioner crate – components & radiation tests FIP ADUC CARD LOAD SENSORS 12 CHANNEL INPUT STAGE PCB CONN.TAPE Load sensors conditioners – radiation tests RADWG, Semiconductors proposed for 12-channel input stage of conditioner crate: 12 x AD7730 – Analog Devices, CMOS, 24-Bit Sigma-Delta, Bridge Transducer ADC for Load Cell Applications (not tested) 12xMIC4427 – Micrel, MOSFET driver (not tested) 1xCPLD XC95144 – Xilinx CPLD, 144 macrocells, triple mode redundancy (5V logic compatible preffered), Actel if no agreement 1xADUC8xx – Analog Devices, ’51 based MCU with ADC & 12bit DAC (used in FipAduc, tested 100Gy) 12xLED HLMP-1700 or HLMP-1790 (tested 100Gy) 4x rectifying diodes 50WQ03FN (tested100Gy) 1x LM7805 – Linear voltage stabilizer (tested 100Gy) 2x Rail-To-Rail operational amplifier (Vcc=5V ?)

Mateusz Sosin Research status of Low-Beta weighting system Conditioner crate – components & radiation tests Load sensors conditioners – radiation tests RADWG, Equipment locations: IP1: US15 IP2: UA23, UA27 IP8: UA83, UA87 IP5: UJ56 -> after LS1 UL55 Equipment quantity: Each IP -> 2 crates (10 channels for sensors + 2 spares) 8 crates in total

Mateusz Sosin Research status of Low-Beta weighting system ? Questions Load sensors conditioners – radiation tests RADWG, According to future locations of new eqipment and radiation levels – how big is risk of radiation fails in installation places? Because of installation works urgency– is it possible to install electronics and perform the tests later? In that case: Can we treat temporarly our components locations as ‘radiation safety’ areas? According to problems with Xilinx XC95.. CPLD family we can change it for Actel ProAsic3, but is it really necessary in this case? ADC tests: AD7730 & future SAS generation...