Portable Power Tools Cordless Drill Hammer Drill Orbital Sander

Slides:



Advertisements
Similar presentations
Objective Use agricultural mechanics tools properly and safely.
Advertisements

CORDLESS DRILL WHAT IS IT ? WHAT IS IT USED FOR ? click here
Drills & Drilling Drills & Drilling.
Learning objectives: -
Principles of Construction Safety First! Part I Safety Materials for Drill Press, Belt Disk Sander and Router Copyright Texas Education Agency (TEA) 1.
Power Tools Safety. Portable Circular Saws Stock must be well supported in such a way that the kerf will not close and bind the blade.. Thin materials.
Drill Press. General Safety Wear your safety glasses at all times Take off all jewelry Do not wear loose clothing Make sure you are the only person in.
Portable Power Tool Safety. Portable Electric and Cordless Drill Be sure the electric drill is disconnected from the power source before installing bits.
Cutting Machines Foldable Information. DRILL PRESS Related Terms  Center punch  Cutting Oil.
Machining Two introductory projects 1.Support post for mirror mount 2.Vertical micro-rail mount.
Fabrication of Fishtank Platform EAS 199B living with the lab.
Technology Education Shop and lab safety Band Saw Scroll Saw
Wood Screws Woodscrews are available in a wide range of shapes, sizes and materials. While mild steel wood screws are suitable for interior work brass.
Tray Tools, Materials & Processes. The Pillar Drill can be used to drill wood, metal, and plastic. As a general rule the larger the hole you are trying.
Stationary Power Tool Safety
Chapter 21 Processes Used to Separate Wood Materials.
By:Gord Darling Construction Technology
TOOL: Radial Arm Saw NEXT STEP: Radial Arm Saw RESULTS: Finish Top Apron Pieces at 9” L x 4” W x ¾ “ Th PROJECT Square Plant Stand PART Top Apron # NEEDED.
General Information Power tools have replaced many hand tools for doing work in the home and in the workshop They allow more work to be carried out in.
Portable Power Tools Unit 14 Page 180
MACHINE TOOLS & MACHINING TOPIC 4 EXTRA… CLICK HERE FOR MORE ON A TOPIC INDUSTRIAL TECHNOLOGY- TIMBER ASSOCIATED THEORY.
Tray Tools, Materials & Processes. The Pillar Drill can be used to drill wood, metal, and plastic. As a general rule the larger the hole you are trying.
Mantle Clock. Beginning Steps Cut 2 piece 20 x 5 to make the 2 sides and top/bottom Cut 1 10 ¾ and 1- 9 from each 20 piece. This will make a side and.
Portable Power Tools Safety and Use. Portable Power Tools Cordless Drills/Drivers Corded Drills Random Orbit Sander Dual Action Sander Jigsaw Circular.
Portable Power Tools Cordless Drill Hammer Drill Orbital Sander
Woodworking with Power
PLAN #PartProcessTools and equipmentQuality controlSafety *Aprons must be worn is ALL stages of manufacture Tim e 1 MDF base Mark out on MDF piece Pencil,
Production Tools in Technology
Basic Tool Safety and Equipment
SAFETY RULES Follow all directions the first time they are given. Be courteous in language and actions. Be on time and prepared to participate. Respect.
INDUSTRIAL TECHNOLOGY-METAL ASSOCIATED THEORY
Learning Objectives To be able to state the different safety precautions associated with the lathe. To be able to identify and state the function of the.
Intro to Power Tools Ag Mech I Class Notes. Objectives AM15.01 Explain how power tools are used in agricultural mechanics. AM15.02 Know and demonstrate.
1. b. Rip Saw 2. d. Used for cutting with the grain.
BE PREPARED TO TAKE A FEW NOTES TODAY… Pick up the pink sheet at the front.
Proper Use of Agricultural Mechanics Power Tools
Portable Power Tools Quiz
F. 1 Design and Technology
Module-6 Drilling.
Safety Rules for 9 th Grade Shop Radial Arm Saw: Safety Rules Never cut a board that is less than 12 inches long. Always pull the saw using the handle;
Warm-Up Explain when you would use the Belt/Disc sander versus the Oscillating Spindle Sander.
Production Decisions Chapter 6 Mr. Higgins. Objectives Identify the need for a plan of procedure Identify the need for a plan of procedure List the steps.
WOOD MATERIALS TECHNOLOGY 4 th Edition. Chapter 22 Machines.
HEADS UP FOR SAFETY! SAFETY TUTORIAL. HEADS UP! H ANDS ARE THE MOST VULNERABLE PART OF THE BODY. E YES AND EARS ALSO NEED PROTECTION. A SK WHEN YOU ARE.
Copyright © 2010 Delmar, Cengage Learning. ALL RIGHTS RESERVED. Unit 14 Portable Power Tools.
Power tools Session 4 Power drill Circular saw. Power drills Electric versus cordless.
GCSE Resistant Materials Tools and Equipment
Principles of Manufacturing Safety First! Part I
Machine Safety Rules. Miter Saw Instructor must be present when you are using this machine. Keep wood flat and against fence Hold down wood Do not remove.
On/off switch Depth stop Quill lock chuck Tilting table Lower table or base Variable speed pilot wheel motor Feed handle Table locking clamp column.
Safety Mr. Colby – Technology Education. What is Manufacturing?  Manufacturing is using Materials and Processes to make a Product.
Tools. Corded Power Drill These are used to drill larger holes or holes in more substantial materials. You would use this type of drill to drill metal.
hand tool Identification
Used for cutting wood and plastic
SCROLL SAW CHAPTER 26.
General & Machine Safety Notes
The scroll saw.
Remember tools and their safety practices related to the agricultural mechanics industry. Objective 6.03.
Tools.
Year 7 RM Wood Belt Sander
Lab Safety.
Proper Use of Agricultural Mechanics Power Tools
Drill Press Safety.
Facing & Center Drilling
Portable Power Tools Cordless Drill Hammer Drill Orbital Sander
St Andrews High School Shaping Wood.
Chapter 25 Woodturning.
Wood Joints 2 Quiz.
Drills & Drilling Drills & Drilling.
Bench Tools (Woodwork)
Presentation transcript:

Portable Power Tools Cordless Drill Hammer Drill Orbital Sander Delta Sander Jig Saw Belt Sander Biscuit Cutter Router Angle Grinder

Cordless Drill Screwdriver Bit Keyless Chuck Forward / Reverse Switch Adjustable Clutch On / Off switch Battery Pack The Cordless Drill can be fitted with a drill bit (1mm to 10mm) for drilling small holes, a Countersink bit for countersinking holes or a Screwdriver bit for driving in screws. When using a cordless Drill you must Wear Goggles Tie any long hair back Tuck in any loose clothing

Cordless Drill When using the cordless drill to drill holes remember to set the drill to its highest speed and set the clutch to drill. Clutch Setting Speed Setting 2

Cordless Drill When using the cordless drill to drive in screws follow these steps 1) Choose the screwdriver bit that best fits the screws you are using. 2) Set the speed to it lower setting 3) Set the clutch to 1/6 for small screws & 7/15 for heavier screws 4) Finally make sure the drill is held at 90˚ to the workpiece and drive the screw in slowly Screwdriver bits

Orbital Sander Variable Speed Control Flex On / Off Switch When using an orbital sander you must Wear Goggles Tie any long hair back Tuck in any loose clothing On / Off Switch The Orbital Sander is used to sand wide flat boards

  Orbital Sander The Orbital Sander is used to sand wide flat boards And should not be used to sand edges (use a Jack Plane to finish an edge) 

4kg SDS Hammer Drill Hammer On/Off Switch On/Off Switch Variable Speed Control SDS Chuck When using any power drill you must Wear Goggles Tie any long hair back Tuck in any loose clothing

4kg SDS Hammer Drill Masonry Bits The picture above shows a powerful hammer drill suitable for drilling large holes in concrete. Masonry drills are used to drill holes in concrete. They are generally made from toughened steel with a Tungsten tip. Tungsten Tip

Jig Saw On/Off Lock Button Variable Speed Control Flex Pendulum Adjustment Lever Blade On / Off Switch When using a Jig Saw you must Wear Goggles Tie any long hair back Tuck in any loose clothing Base Plate

Jig Saw Pendulum Adjustment lever Blades are available for a wide range of materials- Hardwoods, softwoods, man made boards and even metal cutting blades. When using the Jig saw first choose an appropriate blade for the material you are cutting. Next set the Pendulum adjustment lever 0 for a Slow fine finish 3 for a Fast rough finish

Jig Saw The Jig saw can be used to cut simple curves in a variety of materials. When using this tool great care must be taken not to cut through the workpiece and into the desk

Jig Saw Fence Fitting a fence to the Jig saw will allow you to cut parallel strips

Jig Saw After drilling some holes the Jig saw can also be used to cut out internal shapes

Portable Belt Sander Dust Collection Bag On/Off Button Belt When using a Belt sander sander you must Wear Goggles Tie any long hair back Tuck in any loose clothing Belt

Portable Belt Sander Industrial Belt Sander The Belt Sander is normally used where a lot of material needs removed over a large area.

Delta Sander On/Off Switch Dust Extraction Port Sanding Pad When using a Delta Sander you must Wear Goggles Tie any long hair back Tuck in any loose clothing The Delta Sander can be used to sand inside tricky corners Spare Sanding Pads

Delta Sander As shown in these pictures the delta sander can be used to sand difficult areas on a project Remember it is always better to sand all the parts of any project Before you glue it together

Biscuit Jointer Beech Biscuit On/Off Button Flex When using a Biscuit Jointer you must Wear Goggles Tie any long hair back Tuck in any loose clothing Flex

Biscuit Jointer The Biscuit Jointer is often used when you need to glue a number of narrower strips together to form a wide board

Biscuit Jointer Stage 1 Stage 1: Set the strips out, best face up, laying the biscuits out not too near the edge Stage 2 Stage 2: Use a Try Square to mark the centers of the biscuits

Biscuit Jointer Stage 3 Stage 3: Clamp the first strip to the desk. Depth setting Stage 4: Make sure the cutter is set to the correct depth (usually the centre of the wood)

Biscuit Jointer Stage 5 Stage 5: Align the Biscuit Jointer on the centre of the joint and cut the first slot. (Remember To wear Goggles) Stage 4 Stage 6: Cut the rest of the slots. (Remember you won’t need slots on the outside edges)

Biscuit Jointer Stage 7 Stage 7: Assemble without glue. Stage 8 Dry Cramp Cramp all the pieces together without glue and make sure all joints fit.

Biscuit Jointer Stage 9 Stage 7: Apply glue to both sides and in slots Cramp Cramp all the pieces together then use a damp cloth to remove any excess glue The End

Router A Router can be used to produce a wide range of wooden moldings On/Off Button Depth Stop Router Bit When using a Router you must Wear Goggles Tie any long hair back Tuck in any loose clothing

Router Router safety is a matter of controlling the router and securing the work piece. With a router spinning at 22,000 RPM bad things can happen fast. Listen to the sound of your router, it should sound the same cutting as when at an idle, if not you are forcing it. The larger the diameter of the bit the slower the speed of the router. Always rout against the direction of the router bit, anticlockwise around the outside of an object or clockwise around the inside of an object when routing freehand. Make a series of shallow passes rather than one cut if a lot of material has to be removed. Use an edge guide whenever possible. Always use the router in a vertical position, gripped in both hands, in a comfortable stance. Note due to Highland Council Insurance restrictions pupils are not allowed to use this tool

Angle Grinder The Angle Grinder can be used to remove steel much quicker than you could file. It is important not only to wear goggles when using this tool but to be aware that this tool throws sparks across the room and great care must be taken not to endanger other pupils.

The End