Solving Simultaneous Equations in Mathcad

DISCLAIMER & USAGE The content of this presentation is for informational purposes only and is intended for students attending Louisiana Tech University only. The authors of this information do not make any claims as to the validity or accuracy of the information or methods presented. Any procedures demonstrated here are potentially dangerous and could result in damage and injury. Louisiana Tech University, its officers, employees, agents and volunteers, are not liable or responsible for any injuries, illness, damage or losses which may result from your using the materials or ideas, or from your performing the experiments or procedures depicted in this presentation. The Living with the Lab logos should remain attached to each slide, and the work should be attributed to Louisiana Tech University. If you do not agree, then please do not view this content. boosting application-focused learning through student ownership of learning platforms

Σ 𝐹 𝑥 =− 𝐹 𝐴 ∙𝑐𝑜𝑠 32° + 𝐹 𝑐 ∙𝑐𝑜𝑠 10° =0 Two equations and two unknowns Class Problem: Uncle Fred, who weighs 200 lbs., is trying out his new zip line. Unfortunately, the bearings in his homemade zip line lock up, causing him to come to rest as shown. Determine the tension in the zip line on each side of the pulley. NOTE: The tension on each side of a frictionless pulley is ALWAYS equal, and if the pulley was frictionless, Uncle Fred would come to rest when the angles in front of him and behind him became equal. However, this pulley is NOT frictionless. Solution: Force A 𝐹 𝐴𝑥 =− 𝐹 𝐴 ∙𝑐𝑜𝑠 32° 𝐹 𝐴𝑦 = 𝐹 𝐴 ∙𝑠𝑖𝑛 32° A 32° 10° 𝐹 𝐴 𝐹 𝐶 𝑊𝑒𝑖𝑔ℎ𝑡=200𝑙𝑏𝑠 C B Force C 𝐹 𝐶𝑥 = 𝐹 𝑐 ∙𝑐𝑜𝑠 10° 𝐹 𝐶𝑦 = 𝐹 𝑐 ∙𝑠𝑖𝑛 10° Force W (weight) 𝑊 𝑥 =0 𝑊 𝑦 =−200𝑙𝑏 Σ 𝐹 𝑥 =− 𝐹 𝐴 ∙𝑐𝑜𝑠 32° + 𝐹 𝑐 ∙𝑐𝑜𝑠 10° =0 Two equations and two unknowns Σ 𝐹 𝑦 = 𝐹 𝐴 ∙𝑠𝑖𝑛 32° + 𝐹 𝑐 ∙𝑠𝑖𝑛 10° −200𝑙𝑏=0

Solving Simultaneous Equations in Mathcad Set up your sheet using proper formatting Enter all known variables Insert the Solve Block Math Tab > Solve Block Three sections of the Solve Block: Guess Values: Enter initial guess values for the unknowns to provide a starting point which allows the algorithm to converge toward a solution Constraints: Enter the equations, using <ctrl> = Solver: Solves the simultaneous equations Be sure to assign a new name to the unknown variables in the column matrix Press <shift> : Type find and then enter the names of the variables defined in “constraints” in parentheses Press = Refer to the sample worksheet on the downloads page for more tips