1. Week Four Design & Simulation Example slides

2. Agenda Review the tiny example (Minako “logic”)from last week – look at the detailed static timing report with a constraint added in – Brute force a simulation Do the same for a shift register Give example of combining modules and do the same (MIX) Look at Honkin’ Shifter Experiment

3. Logic: Code and Schematic module Logic( input A, input B, input C, input D, output OUT ); assign OUT = A & B | C & D; endmodule

4. Logic.ucf NET "A" LOC= P86; NET "B" LOC = P87; NET "C" LOC = P11; NET "D" LOC = P12; NET "OUT" LOC = P43; TIMESPEC TS1 = FROM:PADS(A):TO:PADS(OUT):9; TIMESPEC TS2 = FROM:PADS(B):TO:PADS(OUT):9; TIMESPEC TS3 = FROM:PADS(C):TO:PADS(OUT):9; TIMESPEC TS4 = FROM:PADS(D):TO:PADS(OUT):9;

5. Piece of Static Timing Report

6. module LogicTestbench; // Inputs reg A; reg B; reg C; reg D; // Outputs wire OUT; // Instantiate the Unit Under Test(UUT) Logic uut (.A(A),.B(B),.C(C),.D(D),.OUT(OUT) ); initial begin // Initialize Inputs A = 0; B = 0; C = 0; D = 0; // Wait 100 ns for global reset to finish #100; // Add stimulus here A=1; B=1; C=0; D=0; // Wait 100 nsec for delay #100 A=0; B=0; C=0; D=0; // Wait 100 nsec for delay #100 A=0; B=0; C=1; D=1; //wait 100 nsec for delay #100 A=0; (ETC.)

7. Logic Waveforms (functional Sim)

8. Logic Waveforms (timing Sim) Note time delay due to routing delays

9. module Shifter( output reg DO, input [7:0] DI, input CLOCK, input RESET, input LOAD ); parameter piso_shift = 8; reg [piso_shift-2:0] DI_REG; //reg DO; always @(posedge CLOCK) if (RESET) begin DI_REG <= 0; DO <=0; end else if (LOAD) begin DI_REG <= DI[piso_shift-1:1]; DO <= DI[0]; end else begin DI_REG <= {1'b0, DI_REG[piso_shift-2:1]}; DO <= DI_REG[0]; end endmodule Shifter Verilog & RTL Schematic

10. Shifter: Simulation File `timescale 1ns/1ps module ShifterTBW; wire DO; reg [7:0] DI = 8'b00000000; reg CLOCK = 1'b0; reg RESET = 1'b0; reg LOAD = 1'b0; parameter PERIOD = 40; parameter real DUTY_CYCLE = 0.5; parameter OFFSET = 100; initial // Clock process for CLOCK begin #OFFSET; forever begin CLOCK = 1'b0; #(PERIOD-(PERIOD*DUTY_CYCLE)) CLOCK = 1'b1; #(PERIOD*DUTY_CYCLE); end

11. Shifter UUT (.DO(DO),.DI(DI),.CLOCK(CLOCK),.RESET(RESET),.LOAD(LOAD)); initial begin // ------------- Current Time: 105ns #105; RESET = 1'b1; DI = 8'b10101010; // ------------- Current Time: 145ns #40; RESET = 1'b0; // ------------- Current Time: 185ns #40; LOAD = 1'b1; // ------------- Current Time: 225ns #40; LOAD = 1'b0; // ------------------------------------- end endmodule

12. Shifter: Waveform

13. Mix: 8 Bit Register module register(C,D,CLR,Q); input C,CLR; input [7:0] D; output [7:0] Q; reg [7:0] Q; always @ (posedge C or posedge CLR) begin if (CLR) Q<= 8'b00000000; else Q<=D; end endmodule

14. Dual 8 Input, 8 Output Mux module octal_mux(INA,INB,OUT,SEL); input [7:0]INA; input [7:0]INB; output [7:0]OUT; input SEL; assign OUT [0] = (~SEL&INA[0]) | (SEL&INB[0]); assign OUT [1] = (~SEL&INA[1]) | (SEL&INB[1]); assign OUT [2] = (~SEL&INA[2]) | (SEL&INB[2]); assign OUT [3] = (~SEL&INA[3]) | (SEL&INB[3]); assign OUT [4] = (~SEL&INA[4]) | (SEL&INB[4]); assign OUT [5] = (~SEL&INA[5]) | (SEL&INB[5]); assign OUT [6] = (~SEL&INA[6]) | (SEL&INB[6]); assign OUT [7] = (~SEL&INA[7]) | (SEL&INB[7]); endmodule

15. Mix: Bolting them Together module MIX (CLOCK1,CLOCK2,CLEAR,SELECT,INPUTA,INPUTB,OUTPUT); input [7:0]INPUTA; input [7:0]INPUTB; output [7:0]OUTPUT; input SELECT; input CLOCK1; input CLOCK2; input CLEAR; wire [7:0]INA; wire [7:0]INB ; register copy1 (CLOCK1,INPUTA,CLEAR,INA); register copy2 (CLOCK2,INPUTB,CLEAR,INB); octal_mux copy3 (INA,INB,OUTPUT,SELECT); endmodule

16. MIX RTL

17. Zoom into Copy1

18. Mix: Simulation File module Mix_tb; reg CLOCK1 = 1'b0; reg CLOCK2 = 1'b0; reg CLEAR = 1'b0; reg SELECT = 1'b0; reg [7:0] INPUTA = 8'b00000000; reg [7:0] INPUTB = 8'b00000000; wire [7:0] OUTPUT; parameter PERIOD = 100; parameter real DUTY_CYCLE = 0.5; parameter OFFSET = 100; initial // Clock process for CLOCK1 begin #OFFSET; forever begin CLOCK1 = 1'b0; #(PERIOD-(PERIOD*DUTY_CYCLE)) CLOCK1 = 1'b1; #(PERIOD*DUTY_CYCLE); end

19. MIX UUT (.CLOCK1(CLOCK1),.CLOCK2(CLOCK2),.CLEAR(CLEAR),.SELECT(SELECT),.INPUTA(INPUTA),.INPUTB(INPUTB),.OUTPUT(OUTPUT)); initial begin // Process for CLOCK1 // ------------- Current Time: 100ns #100; INPUTA = 8'b00001010; // ------------------------------------- // ------------- Current Time: 135ns #35; CLEAR = 1'b1; INPUTA = 8'b00000101; // ------------------------------------- // ------------- Current Time: 235ns #100; CLEAR = 1'b0; INPUTA = 8'b00001010; INPUTB = 8'b00001111;

20. // ------------------------------------- // ------------- Current Time: 335ns #100; CLOCK2 = 1'b1; INPUTA = 8'b00000101; INPUTB = 8'b00000000; // ------------------------------------- // ------------- Current Time: 435ns #100; INPUTA = 8'b00001010; INPUTB = 8'b00001111; // ------------------------------------- // ------------- Current Time: 535ns #100; CLOCK2 = 1'b0; SELECT = 1'b1; INPUTA = 8'b00000101; INPUTB = 8'b00000000;

21. // ------------------------------------- // ------------- Current Time: 635ns #100; INPUTA = 8'b00001010; INPUTB = 8'b00001111; // ------------------------------------- // ------------- Current Time: 735ns #100; CLOCK2 = 1'b1; INPUTA = 8'b00000101; INPUTB = 8'b00000000; // ------------------------------------- // ------------- Current Time: 835ns #100; INPUTB = 8'b00001111; // ------------------------------------- // ------------- Current Time: 935ns #100; CLOCK2 = 1'b0; // ------------------------------------- end

22. Mix: Waveform