1. Take HV harnesses with label (IHV2) and transfer on the Stacking table. 1.1 Inspect HV harnesses visually. 2.1 Insulate HV Flex with 3M™ VHB™ Tape.

Slides:

Advertisements

Similar presentations

F AST T RACK REMOTE SWITCH WIRING SET UP FOR THE LIGHT BoardPlug Power strips relay Wiring Harness.

Advertisements

Routed Systems Presented by: Bassam Najar, Design Engineer Butler International Inc.

Equipment for Assembly Fluke Multimeter 115 True RMS Glue Ring Jig Flathead screwdriver 60 Watt desk lamp HIOS Cl 4000 Electric screw driver Anti-static.

CricketSat Assembly.

Assembling a Functional Multi-Wire Proportional Counter - Page 1 Work in pairs. One person will take the chamber apart, and the other will reassemble it.

Procedures during Tracker Connection WPA meeting 3 rd December 2007, Michael Eppard, CERN Installation sequence Manpower needs for installation work.

1 Ladder assembly steps HFT PIXEL updated for ultimate chip ladders 2/12/2012 ladder fixture u.SLDASM.

AMS-02 tracker mechanics status of assembly and integration at UniGe Outer planes: - Tests of evaporator (cooling loop) integration - Tools to develop.

Wire bundles connecting to Keyence Sensors (screw plug on other end) Colored Wires from bundles (brown, blue, white are nonfunctional, cap with scotch.

Plan for MRPC Production Yongjie Sun Center of Particle Science and Technology University of Science and Technology of China.

1 Student Hands On Training I (2009) Construction, Integration, and Test Construction, Integration, and Test.

November Vertex 2002 Kazu Hanagaki1 Layer 0 in D0 Silicon Tracker for run2b Kazu Hanagaki / Fermilab for D0 run2b Silicon Tracker group Motivation.

PRR TRD COOLING A. Marín (GSI) 7/01/2004 ALICE PRR TRD COOLING P.Glässel, A.Marín, V.Petracek, J.Stachel, M.R.Stockmeier, J.P.Wessels ALICE PRR TRD COOLING.

GLAST LAT ProjectF2F, June 15, 2005 GLAST Large Area Telescope: Performance & Safety Assurance Joseph Cullinan SLAC Performance & Safety Assurance Manager.

1 Module and stave interconnect Rev. sept. 29/08.

MM mechanical prototype Work progress at CERN MicroMegas General Meeting, CERN, 5-6 November

Institute Of Applied Technology ATE 1012 Grade 10 Eng. Rose Hasan.

Basic Soldering Tips and Techniques! RM1B. Before starting the construction of a soldering project, be sure that your soldering iron tip is in good shape!

Technology-Assisted Assessment Inquiry Part 1

Weld Types - Lap Weld UVU CRT Lap Weld  Many automotive structural panels are assembled using a lap joint.  Technicians must make test welds visually.

Soldering Building permanent circuits. Soldering accomplishes two things Electrical connections Mechanical connections.

Plated Through Hole Soldering Materials by Lindsay Craig.

June 8-th 2004W.Baldini1 Ferrara production center Ferrara production center Production Readiness Review OverviewOfOperations P R R.

Title: Corvette C5 Column Lock Bypass Originator: John Neese Date: 30 Jan 2005 Revision: Sheet: 1 of 6 Column Lock Bypass.

Chiho Wang ATLAS TRT Duke University Dubna, May Fuse Box Production Chiho Wang/Jack Fowler.

Unit 201: Health and safety in building services engineering

17/06/2010UK Valencia RAL Petals and Staves Meeting 1 DC-DC for Stave Bus Tapes Roy Wastie Oxford University.

Ladder assembly steps HFT PIXEL 1/04/2009 ladder fixture.SLDASM.

Experience with the MVD Living around the beam pipe Components, connections, signals, systems Hubert van Hecke - Los Alamos.

FEBRUARY 2003 Pixel Support Tube A. Smith LBNL 1 ATLAS Pixel Support Tube PRR: Parts Pixel Support Tube Production Readiness Review Parts Overview Alexis.

NSQP MEETING Valery AKHNAZAROV January 20th 2011 ISP PP0 Board Bonding Procedure Type 1 Type 3 Type 4peek Type 4 Assembly Name: ISP ASM Parts.

Activities Status and Plan for the week D. Giugni / INFN Milano D. Giugni Monday Meeting

IPC Assembly and Test Palletization of parts is a standard process in many instances for both test and assembly. This can be achieved using.

Table of Contents Unit 1- Understand the Problem Unit 2- Gather Information Unit 3- Develop Solutions Unit 4- Implement A Solution Unit 5- Test and Evaluate.

Some questions:  In which order cables will be put ?  Who, where will put PS signal cables in bundles ?  Which kind of cable binders: velcro or panduit.

NSQP X-1 ASSEMBLY Lessons learned Sébastien MICHAL January 30 rd 2012.

Nov. 8, 2001M. Garcia-Sciveres -- PP0 & Service Panels1 PP0 & Service Panels 1.Introduction 2.Technical Status 3.Goals for 2002.

ATLAS Pixel Detector September 2003 Services E. Anderssen LBNL Service Connectivity from Module to PP1b Eric Anderssen LBNL Pixel Services Meeting, CERN.

Building A Co-Cure Cable Thomas Johnson

MFT WG5: ladder disk and global assembly Stéphane BOUVIER & Sébastian HERLANT MFT WG7: Mechanics and Thermal studies Jean-Michel BUHOUR & Emili SCHIBLER.

Production Readiness Review at PNPI Chamber assembling: Main production and quality control steps 30 January 2004 – G.Alkhazov 1.Input components control.

Service channels between Tracker and PP1 TK-PP1 Cable Channel Review 14 September 2007, Antti Onnela, CERN Installation order and Component status Mock-up.

Oct/07/2010Pixel PP0 opto replacement issues1 1 1 PP0 Opto Replacement Issues Philippe Grenier, Martin Kocian, Dave Nelson, Marco Oriunno, Su Dong, Charlie.

8 June 2006A.Ciocio - SCTSG1 Status of Type IV Cables Cables production –resumed in February after 3 months stop –See ID week February ‘06 Delivery of.

Roy Hannaford October 23-24, 2002 RFP Review DFBX Feedbox LEAD SPLICE SPECIFICATION  BY: ROY HANNAFORD.

NSQP MEETING Valery AKHNAZAROV January 20th 2011 Laminate the NTC-HV and PS harnesses Assembly Name: PP1 Penetration Tape Parts requires:

WP7&8 Progress Report ITS Plenary meeting, 10 June 2014 LG, PK, VM, JR.

NSQP MEETING Valery AKHNAZAROV January 20th 2011 Corrugated Panel Bonding Procedure Assembly Name: ISP Corrugated Panel ASM Parts.

Soldering Building permanent circuits. Soldering accomplishes two things Electrical connections Mechanical connections.

1 PST Heater Panel Design The PST heater panels are internally redundant resistive circuits printed onto a Kapton sheet with an aluminum backing. They.

Sensor Module v1.1. Step 1: Sand edges of PCB & drill bolt holes (3mm) Use small green power drill or pillar drill (as available) Goggles Use a piece.

B2GM, Nov 2014 Laci Andricek, MPG Halbleiterlabor 1 PXD Ladder Assembly - Conceptual design of jigs -

RockOn! RockOn! Structure Build RockOn! 2009.

Procedure for MCM rework on tray MID 070

ATLAS pixel module assembly flow

Service channels between Tracker and PP1

Service channels between Tracker and PP1

ob-fpc: Flexible printed circuits for the alice tracker

New field cage LP2 Ole Bach, Bernd Beyer, Volker Prahl

Activities Status and Plan for the week

Activities Status and Plan for the week

Gluing jigs for Demonstrator

STRAIN GAGE CHARACTERISTICS

Module/Ladder Assembly

HCAL HV splice box.

Wiring the Light and Relay

A1 Pole Changeout Energized

Flex studies status. Module flexes: 4 types; M4, M2, M1plane, M1mountain. constraint: components and bondings on the same side. Constraining for the wing.

After service guide for changing PCB

A1 Insulator Changeout Energized

Presentation transcript:

1. Take HV harnesses with label (IHV2) and transfer on the Stacking table. 1.1 Inspect HV harnesses visually. 2.1 Insulate HV Flex with 3M™ VHB™ Tape and kapton. (3M™ Tape + Kapton+ 3M™ Tape, Use VHB ™ Tape Surface Preparation Technical Bulletin ) 2.2 Do not remove the foil from the latest 3M ™ Tape. 2.3 Separate harness in the channel. (Check the position wires in the Inner Service Panel PP0 to PP1B Connectivity plan.) 2.2 Inspect HV harnesses visually and check voltage.

3. Take HV harnesses pin board with label (IHV1) and transfer it on the table. 4. Inspect HV harnesses visually. 4.1 Insulate HV Flex with 3M™ VHB™ Tape and kapton. (3M™ Tape + Kapton+ 3M™ Tape, Use VHB ™ Tape Surface Preparation Technical Bulletin) 4.2 Do not remove the foil from the latest 3M ™ Tape. 5.1 Inspect HV harnesses visually and check voltage. 5.3 Remove the foil from the latest 3M ™ tape and laminate together HV tape.

6.Take HV harnesses with label (IHV1) and transfer on the Stacking table. 7.Separate harness in the channels. (Check the position wires in the Inner Service Panel PP0 to PP1B Connectivity plan.) 8. Inspect HV harnesses visually and check voltage. 9.Pre-laminate together HV harnesses with label (IHV2) and label (IHV1) with 3M™ VHB™ Tape. (Use VHB ™ Tape Surface Preparation Technical Bulletin) 9.1 Check the position Penetration Flex before laminating.

8. Take NTC harnesses pin board with label (NTC2) and transfer it on the table. 9. Inspect NTC harnesses visually. 10. Insulate NTC Flex with 3M™ VHB™ Tape and kapton. (3M™ Tape + Kapton+ 3M™ Tape, Use VHB ™ Tape Surface Preparation Technical Bulletin) 10.1 Do not remove the foil from the latest 3M ™ Tape. 11.Transfer NTC harnesses with label (NTC2) on the Stacking table. 12. Separate harness in the channels. (Check the position wires in the Inner Service Panel PP0 to PP1B Connectivity plan.) 13. Inspect NTC harnesses visually and check voltage. 14. Remove the foil from the latest 3M ™ tape and laminate together HV and NTC tape.

15.Take NTC harnesses pin board with label (NTC1) and transfer it on the table. 16. Inspect NTC harnesses visually. 17. Transfer NTC harnesses with label (NTC1 ) on the Stacking table. 18. Separate harness in the channels. (Check the position wires in the Inner Service Panel PP0 to PP1B Connectivity) 19. Inspect NTC harnesses visually and check voltage 20. Remove the foil from the latest 3M ™ tape and laminate together NTC tape. (Use VHB ™ Tape Surface Preparation Technical Bulletin) 21. Fix every bunch of wires. transfer plate

22. Transfer NTC/HV harness stacking to the soldering table Use the device to transfer NTC/HV harness.

Potential problems with the wiring bundles

23. Transfer ISP harnesses with label (ISP3) on the Stacking table. 24. Inspect IPS harnesses visually and check voltage. 25. Separate harness in the channels. (Check the position wires in the Inner Service Panel PP0 to PP1B Connectivity plan.) 26. Insulate ISP3 Flex with 3M™ VHB™ Tape and kapton Use VHB ™ Tape Surface Preparation Technical Bulletin Do not remove the foil from the latest 3M ™ Tape. 27. Take IPS harnesses pin board with label (ISP2) and transfer it on the Stacking. 28. Separate harness in the channels. (Check the position wires in the Inner Service Panel PP0 to PP1B Connectivity plan.) 29. Inspect IPS harnesses visually and check voltage. 30. Remove the foil from the 3M ™ tape and laminate together ISP tape Use VHB ™ Tape Surface Preparation Technical Bulletin. 31. Take IPS harnesses pin board with label (ISP1) and transfer it on the Stacking. 32. Separate harness in the channels. (Check the position wires in the Inner Service Panel PP0 to PP1B Connectivity plan.) 33. Inspect IPS harnesses visually and check voltage. 34. All IPS harnesses Insulate kapton tape and Pre-laminate together with 3M™ VHB™ Tape Use VHB ™ Tape Surface Preparation Technical Bulletin. kapton tape 3M™ VHB™ Tape kapton tape

35. Separate harness the top and bottom PP0 Flex Flat. ( HV on the bottom PP0 Flex Flat, NTC on the top ). 36. Inspect harnesses visually and check voltage. 37. Cut NTC/HV harness. 38. Soldering NTC harness. (Use INNER SERVICE PANEL PP0 to PP1B Connectivity Plan) 39. Transfer ISP harness stacking to the soldering table. 40. Inspect harnesses visually and check voltage. 41. Cut ISP harness. 42. Soldering ISP harness. (Use INNER SERVICE PANEL PP0 to PP1B Connectivity Plan) 43. Install the ISP Corrugated Panel and ISP Bottom Panel, 44. Fix the wire in the ISP Corrugated Panel Install a carbon panel Soldering ENV connectors Fix ENV wire on the carbon panel. 45. Overturn harness. 46. Soldering HV harness. (Use INNER SERVICE PANEL PP0 to PP1B Connectivity Plan ) 47. After all soldering, transfer ISP Panel to the stacking table. cut soldering table

48. Fix the wires on the PP0 Panel. 49. Use the tools and tape for correctly installation of the wires. 50. Take up Extra length wires to the corrugated panel. 51. Fix the wires with glue. glue. tape tools

52. Final bonding flange 53. Spray silicone on the tool. 54. Install ½ flanges in device. 55. Put glue on stacks and 2 shims. 56. Fix stacking in the tool. 57. Install Tool for bending. 58. Bend the bundles. Tool for bending