2 inch PVC pipe divided in four equal parts. Pipe is made pliable by heating.

Slides:

Advertisements

Similar presentations

By: Alex Brett, R.T.P.O.(c).  Cast (with minimum 2” of plaster above trim line)  400ML Silicone Cartridge (durometer of your choice)  400ML Injection.

Advertisements

Optical Manufacturing Solutions 1 Probe Assembly.

Click on this image to open the full PDF document.

Installation Quick Guide AD400 Cylindrical 6/01/13 Doc #

Sandblasted, repainted fender brackets. Mudflaps and rubber buttons to attach them.

RISER SETUP NOTE: All levels of the riser are connected using the same method:

Multi-piece Installation Instructions SAFETY WRAP.

Lesson No 05 Week No. 05 Lesson Name Vice.

1 InnoSys Quick Connect End Effecter Service and Maintenance Procedures Nov. 19, 2007 Rev. B.

Software Installation Install following software as per the sequence mentioned below. 1. Firefox ( Firefox Setup exe ) 2. PKI client ( PKIClient-x32-4[1].5_signed.msi.

Keith Haring was one of the original graffiti artists in New York City during the 1980’s. His first graffiti pieces were seen in the subways. He died in.

By Megan Passmore.  Learn archery and improve on the skill  Be able to consistently shoot in the center of the target.

Configuring a PC. Installing the Mother board To Install the Mother board, fit it into the computer casing. You will then need to Insert 24 pin ATX power.

Technical and Installation 1. What will my slot depth/size for the bottom track need to be? The slot depth for standard flush tracks and full drainage.

Threads, Fasteners, and Springs Chapter Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson.

Installation. Indoor Unit Installation Typical Installation.

BEAM SPIGOTS connected to one DeltaBeam. DOUBLE GUARDRAIL connected to the DeltaBeam.

Types of Threaded Fasteners.  Used to hold parts together  Clearance holes in parts  Nut on other end  Can also be used with a threaded hole.

General Instructions for “KidWind Light” wind tunnel.

Simple Machines  Simple machines are basic machines that are the basis for all other forms of machines.  There are six types of simple machines:  1.

Special Right Triangles Chapter 8 Section 3 Learning Goal: Use properties of 45°-45 °-90 °, and 30 °-60 °-90 ° Triangles  We make a living by what we.

Bourdonova cijev Diferencijalno i apsolutno mjerenje tlaka.

TOB Production - January of 688 rod frames ready. Production rate 3-4 rod frames/day. Shipments (40 rod frames/shipment) started from Helsinki.

1 Mechanical for Oil Heat Mechanical codes. 2 Every state has codes. They may be the same in some states, but different in other states. Always have a.

If I wanted to walk around the yellow area, how far would you need to walk?

Foldable 1. Take out a piece of notebook paper and make a hot dog fold over from the right side over to the pink line.

1 HVACR316 - Piping Copper Tubing and Fittings. 2 Tubing & Fittings No matter what piping material is used in the installation of an air conditioning.

1 HVACR316 - Piping Copper Tubing and Fittings. 2 2 Safety Refrigerant cylinders should be stored and transported in the upright position to keep the.

How to multiply a whole number by a fraction.

Grapple Housing Top Sub Grapple Collet Seal Housing Bottom Sub Seal Housing Metal Seal Ring.

Standard 14 Proposed Issue Paper – Update of Normative References – Section 2.0.

Part of a set or part of a whole. 3 4 =Numerator the number of parts = Denominator the number that equals the whole.

Motor Propeller wrench Screw Nut (2) Cylinder top Tiny screw IGNORE:

1 InnoSys Quick Connect End Effecter Service and Maintenance Procedures Shreveport Assembly 14 MAY, 2008.

Converting hands into inches Week 4 blog post. Step one; find number of hands Say you wanted to measure a horse. If this was the case, you would need.

Controlled chaos EF 151, Section 1A Group 8. The PVC pipe is knocked out from under the tube, releasing the golf ball. The ball then hits the PVC wind.

Installing Arzel EzySlide Dampers. Quick Damper Facts Air driven PVC or Plenum tubing connection Round sizes 4” to 16” Rectangular 4” to 48” ¾” gasket.

INSTALL INSULATION IN BOILER PLANT PROJECT SECTIONS: 1.VALVE JACKETS 2.BOILER REFRACTOR JACKETS 3.PIPING INSULATION / PVC.

VOLUME REVIEW. If r=7 units and x=7 units, then what is the volume of the cylinder shown below? r x.

The Alignment of DTL in CSNS Institute of High Energy Physics, CAS KE Zhiyong

Volume… Cylinders. If r = 6 and x = 13 units, then what is the volume of the cylinder shown below? x r.

Thomas Gutierrez Austin Shoemaker Shane Upchurch Ryan Kaysen Joey Miller Kevin Liekweg Prototype Review Mobile Laptop Desk Week 1.

Assembly of steering.

Major Skeletal Muscles

Section 2.1 Writing Equations

The output of one device acts as the input of the next.

Date of download: 10/18/2017 Copyright © ASME. All rights reserved.

Anatomical Model Labeled

Controller Rework.

The Appendicular Skeleton

Measuring Inches.

AM-LINERII® INSTALLATION PROCEDURE Charles A. Munson 9/21/2018.

Torque and Simple Machines

Modern Automotive Technology PowerPoint for by Russell Krick

Horizontal Installation Overview

Volume of solids.

CYLINDER CASE FIG 601 P1 204.

זכויות סוציאליות.

Learning Target 7.59 I can describe the roots of the Scientific Revolution based upon Christian and Muslim influences.

a + 2 = 6 What does this represent? 2 a

Irrigation - Garden – Plumbing

Measuring Inches.

Draw a Neuron: Part II On the other half of your paper, draw what a neuron looks now that we have gone over its structure. Be sure to label!

Engineering Materials

Chapter 6 Measuring.

Threads, Fasteners & Springs

Divide 9 × by 3 ×

Anatomical Model Unlabeled

Presentation transcript:

2 inch PVC pipe divided in four equal parts

Pipe is made pliable by heating

Flaps are opened to receive shuttle lock.

Shuttle lock installed.

Shuttle lock installed with screws. Flaps are then molded around a cylinder the size of the residual limb.

Forearm section is 1 1/2 inch PVC. Hand (Ellen Meadows Hand Project) is attached on end of the tubing.

Liner with locking pin is installed.

Short residual limb

Another short residual limb.

Finished arm

Relaxed arm

Another new arm.

Completed arm