Soldering Dennis Yuan Fall 2013. What is it for? Making good conductive contact between a component and the PCB Through-hole parts Surface mount parts.

Slides:

Advertisements

Similar presentations

BASIC HAND SOLDERING MULTICORE SOLDER

Advertisements

EMS1EP Lecture 3 Intro to Soldering Dr. Robert Ross.

AnaSonde Assembly. What is the AnaSonde? *Reads temperature, pressure, and humidity data from the atmosphere *After it is sent into the atmosphere, it.

Motor & Encoder Mounting Guide. Bill of Materials 1. 10:1 Micro Metal Gearmotor HP item # 999 X 2 2. Pololu Micro Metal Gearmotor Bracket Extended Pair.

Lesson 14 Soldering. What is soldering? Soldering is a method of applying an alloy, of lower melting point, to join metal parts together. Soldering can.

Placing & Soldering Components Electronics 1 CVHS.

Electrical Repair Soldering and Crimping By Fernando Martinez And Rudy.

Today’s Objectives: Soldering Soldering is non-trivial, especially surface mount components Soldering is non-trivial, especially surface mount components.

Soldering 101 A Really HOT Topic. Soldering The process of making an electrical connection by melting low-temperature metal alloys around component leads.

Digital Electronics Soldering & De-soldering. 2 This presentation will… Review the tools needed to solder and de-solder electronic components. Demonstrate.

Lesson Objectives To learn how to solder components onto a circuit board safely and correctly. Success Criteria Must Be able to understand the health and.

Electronics Merit Badge Class 4 5/17/2015Electronics Merit Badge Class National Scout Jamboree1.

1 SPIRIT Silicon Prairie Initiative on Robotics in Information Technology Soldering and Building a Battery Tester.

1 Chelmsford Amateur Radio Society Intermediate Licence Course Carl Thomson G3PEM Slide Set 12: v Jun-2007 (10) Soldering Chelmsford Amateur Radio.

Intermediate Course (10) Soldering Karl Davies East Kent Radio Society EKRS 1.

Surface Mount Device Soldering Materials by Linz Craig.

1 DemoSat Soldering DemoSat Training Boulder, Colorado December 7, 2002.

Colorado Space Grant Consortium Soldering 101. Caution: - Soldering is dangerous if not respected - Be mindful of where you are and where the soldering.

Basic Soldering Tips and Techniques! RM1B. Before starting the construction of a soldering project, be sure that your soldering iron tip is in good shape!

Soldering & The Tinning Process

Introduction to Soldering

Soldering Building permanent circuits. Soldering accomplishes two things Electrical connections Mechanical connections.

How To Solder By: Stephen Eibling.

Plated Through Hole Soldering Materials by Lindsay Craig.

The World Leader in High-Performance Signal Processing Solutions Surface-Mount IC Prototyping Boards James Bryant European Applications Manager.

COB 08 RTM Fuse Modification Required – Soldering iron capable of removing resistor without damaging board. Metcal with tweezer attachment recommended.

PRACTICAL ELECTRONICS MASTERCLASS (Mr Bell) 1. Basic Electronic Components These components will be discussed further during the course, also have a look.

Soldering Safety – Soldering Irons are very HOT! Name: 1. When I am not using the soldering iron, I should return it to the holder because________ _________________________.

Handout from Clinic Conducted by Bernard Kempinski at several NMRA conventions

CVD PCB, first steps. 15 mm 25 mm Chip area. No ground plane underneath the chip. Bulk isolated => only one ground line Power lines Connector: 11,1mm*2,1mm:

Soldering. Soldering Tools Soldering Iron Soldering Iron Care & Maintenance Tinning Process Good Solder Connections Bad Solder Connections De-Solder Process:

Introduction to Sensors - Part 1 Freshman Engineering Honors Program.

Sumo Robot. Materials Part NameQty 3-9 volt Motor2 Gear sets2 Wheels4 Axles 4 Base1 Straws2 Switches2 Bolts & Nuts4 Hook up wire15'

Introduction to Soldering

SOLDERING is the process of bonding together two or more metal parts with a thin alloy or soldering lead. Soldering is accomplished by heating the metals.

1 Jim Thomas - LBL iTPC Soldering Notes Alexei Lebedev & Jon Wirth with additional notes by Qinghua Xu, Eric Anderssen and Jim Thomas 10/28/2015.

Center for Advanced Research and Technology Electronics Technology Lab

ASSEMBLING THE PCB Have the PCB in front of you as shown. Make sure there are no copper tracks showing. This side is called the component side.

 “High fire” glazes are fired in the large brick kiln to a temperature of 2380° Fahrenheit.  It takes about 24 hours to reach that temperature.

Oisture Tester How to Solder. Learning Objectives Understand the soldering process Practice soldering Continue with design ideas Produce an information.

Soldering Building permanent circuits. Soldering accomplishes two things Electrical connections Mechanical connections.

Soldering Basics.

Soldering 101 I am Geordy. After high school I had a job doing board-level repair on CRT monitors back when they were still worth repairing. I ended up.

MODULE 6: Soldering SUMMER CHALLENGE Electrical Engineering: Smart Lighting Michael Rahaim, PhD Candidate Multimedia Communications Lab Boston University.

A Different Soldering Class “Surface Mount Soldering”

Soldering PCBs – Siren Kit Week 2 of 2

The Engine Cooling System

Introduction to Soldering

Soldering Magic of Electrons © 2011 Project Lead The Way, Inc.

Vocabulary Tinning Wetting Surface tension Flow.

Soldering PCBs – Siren Kit Week 1 of 2

Introduction to Soldering (PCB Bread boards)

Soldering Safely A soldering iron should always be considered hot and handled with care at all times. All injuries must be reported to the teacher at once.

Soldering Technique.

Fault detection Lecture (1).

Electronics Soldering Basics

BASIC HAND SOLDERING MULTICORE SOLDER  most common type for hand soldering has a composition of Tin (Sn60) and Lead (Pb40), with a diameter of 0.71 mm.

Soldering & The Tinning Process

Soldering & De-soldering

Placing & Soldering Components

IT 318: M13 PWB Assembly IT M13.

Soldering & Desoldering

Be able to solder the capacitor and chip holder in place on the PCB.

Forging new generations of engineers

Soldering: Methods, Tips, and Applications

By Gerry Crenshaw WD4BIS

Student Hands On Training Workshop (SHOT 2007)

MOVING ICE WIND GRAVITY

Soldering & De-soldering

Presentation transcript:

Soldering Dennis Yuan Fall 2013

What is it for? Making good conductive contact between a component and the PCB Through-hole parts Surface mount parts

What do I need? Soldering iron Solder Flux Sponge and water

Premise Heat up soldering iron Apply flux Heat up PCB pad with soldering iron Hold solder between soldering iron and pad until it flows Remove solder and iron, allowing the joint to cool

Common mistakes Using too little or too much solder Making the iron too hot or leaving the soldering iron on (can cause damage) Not allowing the solder to flow Trying to remove solder, but ripping up the traces instead

Sidenote on parts selection Do not pick super tiny surface mount parts Do not pick parts without pins Not sure if resistor or dust…

Some tips Do continuity checks! Use flux (only need a little bit) Take care of the soldering irons It takes some practice