Haircutting Ch #16

Principles of Haircutting good haircuts begin with an understanding of the shape of the head ________________________________ ________________________________ ____________________

Reference Points Apex Parietal Ridge Occipital Bone Four Corners

Areas of the head Top Front Sides Crown Nape Back Fringe

Lines & Angles Every haircut is made up of lines and angles Line - thin continuous mark used as a guide Angle- space between 2 lines that intersect at a given point 2 basic lines used in haircutting are straight & curved

Lines & Angles cont’d Horizontal Vertical Diagonal Beveling - (aka- stacking) techniques using diagonal lines to create angles by cutting the ends of the hair with a slight increase or decrease in length

Lines & Angles cont’d Straight lines Angles

Straight lines Straight Lines Horizontal Vertical Diagonal

Angles Angles: beveling, stacking

Elevation Elevation: ________________________ ________________________ ________________________ Sections: ________________________ ________________________ Subsections: ________________________ Graduation: ________________________ ________________________

Graduation _________ 90 degrees: __________ weight

Cutting Line is the angle at which the fingers are held when cutting the line that creates the end shape aka - finger position, finger angle, cutting position

Guidelines _____________________________________________ can be located at the perimeter (outer line) or interior or inner line

Overdirection ________________________________ ________________________________

elevation examples 45-degree with 90-degree Overdirection

Tools Shears - commonly called scissors. Mainly used to cut blunt or straight lines, slide cut, or point cut Texturizing shears - mainly used to remove bulk, also called thinning shears, tapering or notching shears

Types of Texturizing Shears Chunking 5-9 teeth texturizing 12-19 teeth thinning 21-30 teeth blending 38 - 50 teeth

Razor straight razor or feather blades mainly used when a softer effect on the ends of the hair is desired

Clipper & Trimmers Clippers - mainly used when creating short haircuts, short tapers, fades, and flat tops Trimmers - (aka- edgers) mainly used to remove excess or unwanted hair at the neckline and around the ears & crisp outlines

About Shears mainly manufactured in 2 countries Japan & Germany Hardness will determine how long the edge will hold without having to be sharpened Rockwell hardness of 56 or 57 is ideal Rockwell of 63 or more will make the shear brittle

Forged vs. Cast cast - molten steel is poured into mold. disadvantage air bubbles can occur and shear can shatter, significantly less expensive forged - made by hammering or pressing metal into a finished shape, last much longer than cast shears

Parts of a shear Cutting edge Pivot Adjustment knob Finger tang Ring-finger hole Thumb hole Still Blade

Shear Maintenance Daily cleaning and lubrication Daily tension adjustment and balancing Weekly cleaning and lubrication Disinfecting shears Sharpening shears

Purchasing Shears Hold shears in hand. Consider dominant hand design Know how manufactured Learn about steel quality Decide on correct blade edge Select best handle design Be sure of fit Hold shears in hand. Swivel thumb shears. Learn about service agreement. Ask about warranty. Analyze cost. Determine how many needed.

Holding Shears

Palming shears

Posture & Body Position Position the client. Sitting straight ____________________________ Center your weight. Knees slightly bent, not locked Bend one knee to lean slightly Stand in front of section being cut.

Safety in haircutting Palm shears. Do not cut past second knuckle. Take care around ears. Balance shears and place knuckles. Use razor guard. Dispose of blades carefully.

General Haircutting Tips __________________________________________ Be aware of potential danger zones. (ears)

Basic Haircuts Blunt haircut Weight line Stationary guide used Graduated haircut Visual buildup of weight Ends appear stacked Traveling guide used

More basic haircuts Layered haircut Less weight than graduated cuts Creates movement and volume Long layered haircut Gives volume to styles Can be combined with other cuts Layers increase form; short to longer toward perimeter Men’s basic clipper cut

The Graduated Haircut Graduated haircut Classic graduated bob Wedge Shorter shape with rounded weight Keep elevation below 45 degrees with coarse textures and curly hair. ______________________________________________ Check neckline carefully before cutting short. Always use fine teeth of comb and maintain even tension to ensure a precise line.

Layered Haircuts Uniformed layered haircut Long-layered haircut Men’s basic clipper cut Pixie, Caesar Squared layers Shag Faceframe

Layered Haircut Tips Cut the interior first. Do not cut thin hair too short. Do not cut coarse hair shorter than 3 inches in length. Do not cut top layers too short. Use slide cutting to connect top sections to lengths. Work with guideline. _____________________________________________ Use mirror to see elevation. Check both sides by standing in front.

Cutting Curly Hair ____________________________________________ _____________________________________________ Naturally “graduates” itself Expands more than straight hair Texturizing techniques

Razor Cutting Razor parallel to subsection at 45-degree angle _____________________________________________ Effective with blonde hair Avoid using on coarse, wiry, or damaged hair. Always use a guard. Always use a new blade. ______________________________________________ Hold razor at an angle; never force.

Slide Cutting Used to cut or thin hair Blends shorter hair to longer Useful in texturizing ____________________

Scissor over comb Hair held in place with comb. Shear tips remove length. Method used to create short tapers. Works best on dry hair. Lift hair with comb; comb acts as guide. Do not hold hair between fingers. Shears and comb move up head together. Strive for continual motion. Work with small areas. Start at hairline and work up. Cross-check work diagonally. Use barber comb for close areas. Stand in front of client. Place comb. Move comb up head. _________________________________________

Texturizing _________________________________ - performed on the ends of the hair using the tips or points of the shear, can be done on wet or dry hair _________________________________- snipping out pieces of hair at random intervals, generally used on an interior section rather than the ends _________________________________ - process of thinning, strand is cut by a sliding movement with the blades keep partially opened _____________ - use only portion of blade near pivot, best with dry hair _____________ - version of slicing that creates a visual separation, best on short hair Carving the ends - add texture and separation to the perimeter begin 3 inches from ends

Texturizing

Clipper Cutting Tips Work against natural growth pattern for maximum removal Work in small sections (no wider than 3 inches). Determine comb angle.