ACS Annunciators
EIA-485 specification Overview RPT May extend the length 4,000 feet
Control Button CONTROL for: - SLC Relay - NAC Control Modules - Speaker Circuits - Software Zones ACM-24AT and ACM-48A ACM-24AT - Visual Indication ONLY ACM-48A
Rear View
Address Wheels NFS-320 / NFS2-640 MAP NFS / NCA-2 MAP
Keylock Switch Key Lock Connection
Dip Switches
Receive & Transmit LED’s
End of Line Resistor
24V Power Connection
ACS Connection
EIA-485 CircuitsPower Circuits RETROFIT CONSIDERATIONS
- A 64 point map exceeds physical points on an annunciator - So we add an expander ACM-24ATAEM-24AT Address Expansion Note the difference in device population
NOTUSEDNOTUSED ACM-24AT AEM-24AT Set Address Intelligence resides on board Expansion annunciators connect to communication bus and receive information through host ACM ACM-24AT with 64-Point Limit
ACM-48A Set Address Intelligence resides on board AEM-48A Expansion annunciators connect to communication bus and receive information through host ACM NOTUSEDNOTUSED NOTUSEDNOTUSEDNOTUSEDNOTUSED ACM-48A with 64-Point Limit
ACM-24AT AEM-24AT Set Address Intelligence resides on board Expansion annunciators connect to communication bus and receive information through host ACM ACM-24AT with 96-Point Limit AEM-24AT
ACM-48A Set Address Intelligence resides on board AEM-48A Expansion annunciators connect to communication bus and receive information through host ACM ACM-48A with 96-Point Limit
DOORS
CABINETRY
Address Wheel Relationship NFS-320 / NFS2-640 MAP 16
MAP Assignment
SETUP in the NFS-320 and NFS2-640 Pre-defined Maps: ACS GroupAnnunciator Display A 8 System points & Zones 1 – 56 B Zones , 9 F Zones, 8 R Zones, 4 NACs C Loop 1, Modules 1 – 64 D Loop 2, Modules 1 – 64 E Loop 1, Modules 65 – 128 F Loop 2, Modules 65 – 128 G Loop 1, Modules (1 unused point) Loop 2, Modules (1 unused point) H Loop 1, Detectors 1 – 64 I Loop 2, Detectors 1 – 64 J Loop 1, Detectors 65 – 128 K Loop 2, Detectors 65 – 128 L Loop 1, Detectors (1 unused point) Loop 2, Detectors (1 unused point) M For use with FireVoice NFV-25/50ZS N 8 System Points & Zones 1-56 O MAP A 8 System points & Zones 1 – 56 Points 11 – 62 Zones 3 thru 54 SYSTEM POINTS
POINTTYPERED LEDYELLOW LEDSWITCH FUNCTION* 1InputSystem AlarmSystem TroubleAcknowledge 2OutputNot UsedSignal SilencedAlarm Silence 3OutputNot UsedProgram ModeSystem Reset 4OutputNot UsedSupervisoryDrill 5OutputNAC #1 ActiveNAC TroubleControl NAC #1 6InputSecurityP/A Maint AlertNot Used 7InputNot UsedLow BatteryNot Used 8InputNot UsedAC FailNot Used * Pressing the switch button when the Switch Function is "Not Used" causes the associated LED to stop blinking. This is a local acknowledgement at the annunciator only: no message is sent to the panel. SYSTEM POINTS
Pre-defined and USER Maps ACS GroupAnnunciator Display A 8 System points & Zones 1 – 56 B Zones , 9 F Zones, 8 R Zones, 4 NACs C Loop 1, Modules 1 – 64 D Loop 2, Modules 1 – 64 E Loop 1, Modules 65 – 128 F Loop 2, Modules 65 – 128 G Loop 1, Modules (1 unused point) Loop 2, Modules (1 unused point) H Loop 1, Detectors 1 – 64 I Loop 2, Detectors 1 – 64 J Loop 1, Detectors 65 – 128 K Loop 2, Detectors 65 – 128 L Loop 1, Detectors (1 unused point) Loop 2, Detectors (1 unused point) M For use with FireVoice NFV-25/50ZS N 8 System Points & Zones 1-56 O 1 – 10 USER-DEFINED MAPS
SETUP in the NFS-320 and NFS2-640 ACS GroupAnnunciator Display 1 Programmable Annunciator #1 2 Programmable Annunciator #2 3 Programmable Annunciator #3 4 Programmable Annunciator #4 5 Programmable Annunciator #5 6 Programmable Annunciator #6 7 Programmable Annunciator #7 8 Programmable Annunciator #8 9 Programmable Annunciator #9 10 Programmable Annunciator #10
User Defined Maps
User Map Programming Select User Map #1
User Map Programming Select a point TYPE
User Map Programming When you choose the point, installed points appear
User Map Programming Selecting the point will install it on the map
User Map Programming You must decide what to DO with the point
User Map Programming Monitor/Control or Enable/Disable
User Map Programming Select MODIFY to install the point
Final ACS Addressing When the User-Defined map is saved, it will appear in the list
CLICK ACS1 Final ACS Addressing When it’s added, ACS 1 is highlighted providing a quick-link
Final ACS Addressing The quick-link brings you back to the User Map
ACS Map in VeriFire Tools NFS-320 / NFS2-640 MAP
Questions