Digital Logic Lecture 08 By Amr Al-Awamry. Combinational Logic 1 A combinational circuit consists of an interconnection of logic gates. Combinational.

Slides:

Advertisements

Similar presentations

Digital Circuits. Review – Getting the truth table The first step in designing a digital circuit usually is to get the truth table. That is, for every.

Advertisements

1 Combinational Logic Design&Analysis. 2 Introduction We have learned all the prerequisite material: – Truth tables and Boolean expressions describe functions.

التصميم المنطقي Second Course

DPSD This PPT Credits to : Ms. Elakya - AP / ECE.

The Map Method Boolean expressions may be simplified by algebraic means as discussed in Previous lecture However, this procedure of minimization is awkward.

08/07/041 CSE-221 Digital Logic Design (DLD) Lecture-8:

ENGIN112 L13: Combinational Design Procedure October 1, 2003 ENGIN 112 Intro to Electrical and Computer Engineering Lecture 13 Combinational Design Procedure.

Combinational Logic Chapter 4.

CS 151 Digital Systems Design Lecture 13 Combinational Design Procedure.

Combinational Logic1 DIGITAL LOGIC DESIGN by Dr. Fenghui Yao Tennessee State University Department of Computer Science Nashville, TN.

Chapter 3 Combinational Logic Design

Charles Kime & Thomas Kaminski © 2008 Pearson Education, Inc. (Hyperlinks are active in View Show mode) Chapter 3 – Combinational Logic Design Part 1 –

Overview Part 1 – Design Procedure 3-1 Design Procedure

Part 2: DESIGN CIRCUIT. LOGIC CIRCUIT DESIGN x y z F F = x + y’z x y z F Truth Table Boolean Function.

CS 105 Digital Logic Design

Morgan Kaufmann Publishers

Combinational Logic Design CS341 Digital Logic and Computer Organization F2003.

Charles Kime & Thomas Kaminski © 2004 Pearson Education, Inc. Terms of Use (Hyperlinks are active in View Show mode) Terms of Use Lecture 12 – Design Procedure.

Combinational Logic Design

Outline Analysis of Combinational Circuits Signed Number Arithmetic

Chapter 5 Memory and Programmable Logic 5.1. Introduction 5.2. Random Access Memory 5.3. Memory Encoding 5.4. Read Only Memory 5.5. Programmable Logic.

Combinational Logic Chapter 4. Digital Circuits Combinational Circuits Logic circuits for digital system Combinational circuits the outputs are.

Chap 4. Sequential Circuits

Sahar Mosleh PageCalifornia State University San Marcos 1 Multiplexer, Decoder and Circuit Designing.

Chap 3. Chap 3. Combinational Logic Design. Chap Combinational Circuits l logic circuits for digital systems: combinational vs sequential l Combinational.

Dr. Ahmed El-Bialy, Dr. Sahar Fawzy Combinational Circuits Dr. Ahmed El-Bialy Dr. Sahar Fawzy.

Combinational Logic. Outline 4.1 Introduction 4.2 Combinational Circuits 4.3 Analysis Procedure 4.4 Design Procedure 4.5 Binary Adder- Subtractor 4.6.

Combinational Logic Design BIL- 223 Logic Circuit Design Ege University Department of Computer Engineering.

ADDERS Half Adders Recall that the basic rules of binary addition are as indicated below in Table 2-9. A circuit known as the half-adder carries out these.

1 The Chinese University of Hong Kong Faculty of Education Diploma in Education (Part-Time) Winter 1997 Educational Communications and Technology Assignment.

Combinational Logic. Digital Circuits Introduction Logic circuits for digital systems may be combinational or sequential. A combinational circuit.

Module 9.  Digital logic circuits can be categorized based on the nature of their inputs either: Combinational logic circuit It consists of logic gates.

1 Combinational Logic Design Digital Computer Logic Kashif Bashir

CHAPTER 4 Combinational Logic

1 Lecture 22 Sequential Circuits Analysis. 2 Combinational vs. Sequential  Combinational Logic Circuit  Output is a function only of the present inputs.

Logic Gates Logic gates are electronic digital circuit perform logic functions. Commonly expected logic functions are already having the corresponding.

Sneha.  A combinational circuit that performs the addition of two bits is called a half adder.  It has two inputs.  It has two outputs.

CS 105 DIGITAL LOGIC DESIGN Chapter 4 Combinational Logic 1.

1 Chapter 4 Combinational Logic Logic circuits for digital systems may be combinational or sequential. A combinational circuit consists of input variables,

1 CS 151: Digital Design Chapter 3: Combinational Logic Design 3-1Design Procedure CS 151: Digital Design.

CS151 Introduction to Digital Design Chapter 3: Combinational Logic Design 3-1 Design Procedure 1Created by: Ms.Amany AlSaleh.

Karnaugh Maps (K-Maps)

Karnaugh Map and Circuit Design.

Combinational Circuits

ECE 301 – Digital Electronics Logic Circuit Design (Lecture #9)

Lecture 07 Digital logic By Amr Al-Awamry. 4 variables K-Map.

4–1. BSCS 5 th Semester Introduction Logic diagram: a graphical representation of a circuit –Each type of gate is represented by a specific graphical.

C OMBINATIONAL L OGIC D ESIGN 1 Eng.Maha AlGubali.

Logic Design (CE1111 ) Lecture 4 (Chapter 4) Combinational Logic Prepared by Dr. Lamiaa Elshenawy 1.

Chapter 4 Combinational Logic. 4.1 Introduction   Logic circuits for digital systems may be combinational or sequential. A combinational circuit consists.

Combinational Design, Part 2: Procedure. 2 Topics Positive vs. negative logic Design procedure.

Lecture 1 Gunjeet kaur Dronacharya group of institutions.

CS151 Introduction to Digital Design Chapter 3: Combinational Logic Design 3-4 Verification 1Created by: Ms.Amany AlSaleh.

Chap 3. Combinational Logic Design

ECE 3130 Digital Electronics and Design

Combinational Circuits

Combinational Logic Design&Analysis.

Combinational Logic Logic circuits for digital systems may be combinational or sequential. A combinational circuit consists of input variables, logic gates,

Combinational Circuit Design

Computer Architecture CST 250

Chapter 4 Combinational Logic

Karnaugh Maps (K-Maps)

FIGURE 4.1 Block diagram of combinational circuit

ECE 301 – Digital Electronics

Ch 4. Combinational logic

Number Systems and Circuits for Addition

Combinational Circuits

Chapter-4 Combinational Logic

XOR Function Logic Symbol  Description  Truth Table 

Arithmetic Circuits.

Presentation transcript:

Digital Logic Lecture 08 By Amr Al-Awamry

Combinational Logic 1 A combinational circuit consists of an interconnection of logic gates. Combinational logic gates react to the values of the signals at their inputs and produce the value of the output signal, transforming binary information from the given input data to a required output data

Combinational Logic 2 The diagram of a combinational circuit has logic gates with no feedback paths or memory elements.

Analysis Procedure one has previous experience and familiarity with a wide variety of digital circuits.To obtain the output Boolean functions from a logic diagram, we proceed as follows: 1. Label all gate outputs that are a function of input variables with arbitrary symbols— but with meaningful names. Determine the Boolean functions for each gate output. 2. Label the gates that are a function of input variables and previously labeled gates with other arbitrary symbols. Find the Boolean functions for these gates. 3. Repeat the process outlined in step 2 until the outputs of the circuit are obtained. 4. By repeated substitution of previously defined functions, obtain the output Boolean functions in terms of input variables.

Example 1

Example …. Cont.

Truth Table The derivation of the truth table for a circuit is a straightforward process once the output Boolean functions are known. To obtain the truth table directly from the logic diagram without going through the derivations of the Boolean functions, we proceed as follows: 1. Determine the number of input variables in the circuit. For n inputs, form the 2 n possible input combinations and list the binary numbers from 0 to (2 n - 1) in a table. 2. Label the outputs of selected gates with arbitrary symbols. 3. Obtain the truth table for the outputs of those gates which are a function of the input variables only. 4. Proceed to obtain the truth table for the outputs of those gates which are a function of previously defined values until the columns for all outputs are determined.

Truth Table for example

Design Procedure 1. From the specifications of the circuit, determine the required number of inputs and outputs and assign a symbol to each. 2. Derive the truth table that defines the required relationship between inputs and outputs. 3. Obtain the simplified Boolean functions for each output as a function of the input variables. 4. Draw the logic diagram and verify the correctness of the design (manually or by simulation).

Code conversion example

Code conversion k-map 1

Code conversion k-map 2

Code Conversion Implmentation

BINARY ADDER–SUBTRACTOR A combinational circuit that performs the addition of two bits is called a half adder. One that performs the addition of three bits (two significant bits and a previous carry) is a full adder.

Half Adder

Full Adder

Full Adder Implementation

Four bit Adder

Thanks