The MOS Transistor Polysilicon Aluminum.

Slides:



Advertisements
Similar presentations
MICROWAVE FET Microwave FET : operates in the microwave frequencies
Advertisements

6.1 Transistor Operation 6.2 The Junction FET
Chapter 6 The Field Effect Transistor
EE466: VLSI Design Lecture 02 Non Ideal Effects in MOSFETs.
MOSFETs Monday 19 th September. MOSFETs Monday 19 th September In this presentation we will look at the following: State the main differences between.
Department of EECS University of California, Berkeley EECS 105 Fall 2003, Lecture 12 Lecture 12: MOS Transistor Models Prof. Niknejad.
Lecture 11: MOS Transistor
Introduction to VLSI Circuits and Systems, NCUT 2007 Chapter 6 Electrical Characteristic of MOSFETs Introduction to VLSI Circuits and Systems 積體電路概論 賴秉樑.
10/8/2004EE 42 fall 2004 lecture 171 Lecture #17 MOS transistors MIDTERM coming up a week from Monday (October 18 th ) Next Week: Review, examples, circuits.
CMOS Digital Integrated Circuits
Lecture 15 OUTLINE MOSFET structure & operation (qualitative)
Metal-Oxide-Semiconductor (MOS)
EE415 VLSI Design The Devices: MOS Transistor [Adapted from Rabaey’s Digital Integrated Circuits, ©2002, J. Rabaey et al.]
Lecture 10: PN Junction & MOS Capacitors
Lecture #16 OUTLINE Diode analysis and applications continued
The metal-oxide field-effect transistor (MOSFET)
Week 8b OUTLINE Using pn-diodes to isolate transistors in an IC
Chap. 5 Field-effect transistors (FET) Importance for LSI/VLSI –Low fabrication cost –Small size –Low power consumption Applications –Microprocessors –Memories.
Dr. Nasim Zafar Electronics 1 - EEE 231 Fall Semester – 2012 COMSATS Institute of Information Technology Virtual campus Islamabad.
EE105 Fall 2007Lecture 16, Slide 1Prof. Liu, UC Berkeley Lecture 16 OUTLINE MOS capacitor (cont’d) – Effect of channel-to-body bias – Small-signal capacitance.
Metal-Oxide-Semiconductor Field Effect Transistors
Transistors (MOSFETs)
Dr. Nasim Zafar Electronics 1 - EEE 231 Fall Semester – 2012 COMSATS Institute of Information Technology Virtual campus Islamabad.
Semiconductor Devices III Physics 355. Transistors in CPUs Moore’s Law (1965): the number of components in an integrated circuit will double every year;
EE 466: VLSI Design Lecture 03.
Digital Integrated Circuits© Prentice Hall 1995 Introduction The Devices.
ECE 342 Electronic Circuits 2. MOS Transistors
Norhayati Soin 06 KEEE 4426 WEEK 7/1 6/02/2006 CHAPTER 2 WEEK 7 CHAPTER 2 MOSFETS I-V CHARACTERISTICS CHAPTER 2.
Chapter 5: Field Effect Transistor
1 Metal-Oxide-Semicondutor FET (MOSFET) Copyright  2004 by Oxford University Press, Inc. 2 Figure 4.1 Physical structure of the enhancement-type NMOS.
EXAMPLE 6.1 OBJECTIVE Fp = 0.288 V
Norhayati Soin 06 KEEE 4426 WEEK 3/2 13/01/2006 KEEE 4426 VLSI WEEK 3 CHAPTER 1 MOS Capacitors (PART 2) CHAPTER 1.
Chapter 4 Field-Effect Transistors
DMT121 – ELECTRONIC DEVICES
1 Fundamentals of Microelectronics  CH1 Why Microelectronics?  CH2 Basic Physics of Semiconductors  CH3 Diode Circuits  CH4 Physics of Bipolar Transistors.
Filed Effect Transistor.  In 1945, Shockley had an idea for making a solid state device out of semiconductors.  He reasoned that a strong electrical.
NMOS PMOS. K-Map of NAND gate CMOS Realization of NAND gate.
ECE 4339 L. Trombetta ECE 4339: Physical Principles of Solid State Devices Len Trombetta Summer 2007 Chapters 16-17: MOS Introduction and MOSFET Basics.
Norhayati Soin 06 KEEE 4426 WEEK 3/1 9/01/2006 KEEE 4426 VLSI WEEK 3 CHAPTER 1 MOS Capacitors (PART 1) CHAPTER 1.
Junction Capacitances The n + regions forms a number of planar pn-junctions with the surrounding p-type substrate numbered 1-5 on the diagram. Planar junctions.
ECE442: Digital ElectronicsCSUN, Spring-2010-Zahid MOS Transistor ECE442: Digital Electronics.
1 Chapter 5. Metal Oxide Silicon Field-Effect Transistors (MOSFETs)
UNIT I MOS TRANSISTOR THEORY AND PROCESS TECHNOLOGY
Structure and Operation of MOS Transistor
MOSFET Placing an insulating layer between the gate and the channel allows for a wider range of control (gate) voltages and further decreases the gate.
11. 9/15 2 Figure A 2 M+N -bit memory chip organized as an array of 2 M rows  2 N columns. Memory SRAM organization organized as an array of 2.
Norhayati Soin 06 KEEE 4426 WEEK 3/2 20/01/2006 KEEE 4426 VLSI WEEK 4 CHAPTER 1 MOS Capacitors (PART 3) CHAPTER MOS Capacitance.
EE210 Digital Electronics Class Lecture 6 May 08, 2008.
The MOS Transistor Polysilicon Aluminum. The NMOS Transistor Cross Section n areas have been doped with donor ions (arsenic) of concentration N D - electrons.
MOSFET Current Voltage Characteristics Consider the cross-sectional view of an n-channel MOSFET operating in linear mode (picture below) We assume the.
CHAPTER 6: MOSFET & RELATED DEVICES CHAPTER 6: MOSFET & RELATED DEVICES Part 2.
Introduction to semiconductor technology. Outline –6 Junctions Metal-semiconductor junctions –6 Field effect transistors JFET and MOS transistors Ideal.
Integrated Circuit Devices
Metal-oxide-semiconductor field-effect transistors (MOSFETs) allow high density and low power dissipation. To reduce system cost and increase portability,
Spencer/Ghausi, Introduction to Electronic Circuit Design, 1e, ©2003, Pearson Education, Inc. Chapter 2, slide 1 Introduction to Electronic Circuit Design.
Field Effect Transistor (FET)
CP 208 Digital Electronics Class Lecture 6 March 4, 2009.
Transistors (MOSFETs)
The MOS capacitor. (a) Physical structure of an n+-Si/SiO2/p-Si MOS capacitor, and (b) cross section (c) The energy band diagram under charge neutrality.
MOSFET V-I Characteristics Vijaylakshmi.B Lecturer, Dept of Instrumentation Tech Basaveswar Engg. College Bagalkot, Karnataka IUCEE-VLSI Design, Infosys,
course Name: Semiconductors
Damu, 2008EGE535 Fall 08, Lecture 21 EGE535 Low Power VLSI Design Lecture #2 MOSFET Basics.
MOS Transistor Theory The MOS transistor is a majority carrier device having the current in the conducting channel being controlled by the voltage applied.
Chapter 6 The Field Effect Transistor
Recall Last Lecture Common collector Voltage gain and Current gain
Revision CHAPTER 6.
ECE574 – Lecture 3 Page 1 MA/JT 1/14/03 MOS structure MOS: Metal-oxide-semiconductor –Gate: metal (or polysilicon) –Oxide: silicon dioxide, grown on substrate.
Channel Length Modulation
Solid State Electronics ECE-1109
Dr. Hari Kishore Kakarla ECE
Presentation transcript:

The MOS Transistor Polysilicon Aluminum

Two-Terminal MOS Structure Tox is 2nm to 50nm

The equilibrium concentrations of mobile carriers in a semiconductor always obey the Mass Action Law (1) n = the mobile carrier concentrations of electrons p= the mobile carrier concentrations of holes = the intrinsic carrier concentration of silicon, which is a function of the temp T. At room temperature, i.e., T= 300 K, =1.45 x 10^10 cm-3. Assuming that the substrate is uniformly doped with an acceptor (e.g.,Boron) concentration , the equilibrium electron and hole concentrations in the p-type substrate are approximated by (2)

Energy Band Diagram of p-type Silicon Substrate

The band-gap between the conduction band and the valence band for silicon is approximately 1.1 eV. The location of the equilibrium Fermi level within the band-gap is determined by the doping type and the doping concentration in the silicon substrate. The Fermi potential , which is a function of temperature and doping, denotes the difference between the intrinsic Fermi level , and the Fermi level (3)

For a p-type semiconductor, the Fermi potential can be approximated by (4) For an n-type semiconductor (doped with a donor concentration ), the Fermi potential is given by (5) The definitions given in (4) and (5) result in a positive Fermi potential for n-type material, and a negative Fermi potential for p-type material

The electron affinity of silicon, which is the potential difference between the conduction band level and the vacuum (free-space) level, is denoted by The energy required for an electron to move from the Fermi level into free space is called the work function , and is given by (6)

Energy band diagrams of the MOS system Energy band diagrams of the components that make up the MOS system = Work Function of Metal = Electron affinity of Silicon = Electron affinity of Oxide layer

Energy band diagram of the combined MOS system Flat Band Voltage:It is the voltage corresponding to the potential difference applied externally between the gate and the substrate, so that the bending of the energy bands near the surface can be compensated, i.e., the energy bands become "flat.” (7)

The MOS System under External Bias Assume that the substrate voltage is set at , and let the gate voltage be the controlling parameter. Depending on the polarity and the magnitude of , three different operating regions can be observed for the MOS system: Accumulation Depletion Inversion

MOS gate Structure First electrode - Gate : Consists of low-resistivity material such as highly-doped polycrystalline silicon, aluminum or tungsten Second electrode - Substrate or Body: n- or p- type semiconductor Dielectric - Silicon dioxide: stable high-quality electrical insulator between gate and substrate.

Gate and Substrate Conditions for Different Biases Accumulation VG << VTN Depletion VG < VTN Inversion VG > VTN

Accumulation If a negative voltage is applied to the gate electrode, the holes in the p-type substrate are attracted to the semiconductor-oxide interface. The majority carrier concentration near the surface becomes larger than the equilibrium hole concentration in the substrate; hence, this condition is called carrier accumulation on the surface. Note that in this case, the oxide electric field is directed towards the gate electrode. The negative surface potential also causes the energy bands to bend upward near the surface. While the hole density near the surface increases as a result of the applied negative gate bias, the electron (minority carrier) concentration decreases as the negatively charged electrons are pushed deeper into the substrate.

The MOS System under External Bias (Accumulation) The cross-sectional view and the energy band diagram of the MOS structure operating in accumulation region

The MOS System under External Bias (Depletion) A small positive gate bias is applied to the gate electrode. Since the substrate bias is zero, the oxide electric field will be directed towards the substrate in this case. The positive surface potential causes the energy bands to bend downward near the surface. The majority carriers, i.e., the holes in the substrate, will be repelled back into the substrate as a result of the positive gate bias, and these holes will leave negatively charged fixed acceptor ions behind. Thus, a depletion region is created near the surface. Note that under this bias condition, the region near the semiconductor-oxide interface is nearly devoid of all mobile carriers.

The MOS System under External Bias (Depletion) The cross-sectional view and the energy band diagram of the MOS structure operating in depletion mode, under small gate bias

Depth of Depletion Region & Depletion Region Charge Density The mobile hole charge in a thin horizontal layer parallel to the surface is (8) The change in surface potential required to displace this charge sheet by a distance away from the surface can be found by using the Poisson equation (9) Integrating along the vertical dimension (perpendicular to the surface) yields (10) (11) The depth of the depletion region is: The depletion region charge density, which consists solely of fixed acceptor ions in this region, is given by (12)

The MOS System under External Bias (Inversion) If the positive gate bias is further increased i.e As a result of the increasing surface potential, the downward bending of the energy bands will increase as well. Eventually, the mid-gap energy level becomes smaller than the Fermi level on the surface, which means that the substrate semiconductor in this region becomes n-type. Within this thin layer, the electron density is larger than the majority hole density, since the positive gate potential attracts additional minority carriers (electrons) from the bulk substrate to the surface. The n-type region created near the surface by the positive gate bias is called the inversion layer, and this condition is called surface inversion. It will be seen that the thin inversion layer on the surface with a large mobile electron concentration can be utilized for conducting current between two terminals of the MOS transistor.

The MOS System under External Bias (Inversion) The surface is said to be inverted when the density of mobile electrons on the surface becomes equal to the density of holes in the bulk (p-type) substrate. This condition requires that the surface potential has the same magnitude, but the reverse polarity, as the bulk Fermi potential . Once the surface is inverted, any further increase in the gate voltage leads to an increase of mobile electron concentration on the surface, but not to an increase of the depletion depth. Thus, the depletion region depth achieved at the onset of surface inversion is also equal to the maximum depletion depth, , which remains constant for higher gate voltages. Using the inversion condition , the maximum depletion region depth at the onset of surface inversion can be found from (11) as follows (13) The creation of a conducting surface inversion layer through externally applied gate bias is an essential phenomenon for current conduction in MOS transistors

The MOS System under External Bias (Inversion) The cross-sectional view and the energy band diagram of the MOS structure in surface inversion, under larger gate bias voltage

Structure and Operation of MOS Transistor (MOSFET) The physical structure of an n-channel enhancement-type MOSFET

Circuit symbols Circuit symbols for n-channel and p-channel enhancement-type MOSFETs Circuit symbols for n-channel depletion-type MOSFETs

Formation of a depletion region Formation of a depletion region in an n-channel enhancement-type MOSFET

Band diagram of the MOS structure at Inversion Band diagram of the MOS structure underneath the gate, at surface inversion. Notice the band bending by at the surface.

Formation of an inversion layer Formation of an inversion layer (channel) in an n-channel enhancement-type MOSFET

The Threshold Voltage For all practical purposes, there are four physical components of the threshold voltage: the work function difference between the gate and the channel the gate voltage component to change the surface potential at inversion the gate voltage component to offset the depletion region charge the voltage component to offset the fixed charges in the gate oxide and in the silicon-oxide interface.

The Threshold Voltage The work function difference between the gate and the channel reflects the built-in potential of the MOS system, which consists of the p-type substrate, the thin silicon dioxide layer, and the gate electrode. The first component of the threshold voltage The externally applied gate voltage is required to achieve surface inversion So the second component of the threshold voltage.

The Threshold Voltage The depletion region charge density at surface inversion ( ) The depletion region charge density can be expressed as a function of the source-to-substrate voltage The third component that offsets the depletion region charge is Where is the gate oxide capacitance per unit area.

The Threshold Voltage Due to the influence of a nonideal physical phenomenon, there always exists a fixed positive charge density at the interface between the gate oxide and the silicon substrate, due to impurities and/or lattice imperfections at the interface. The (fourth) gate voltage component that is necessary to offset this positive charge at the interface is Combining all of these voltage components For zero substrate bias, the threshold voltage is expressed as follows With source-to-substrate bias voltage

The Threshold Voltage The generalized form of the threshold voltage can also be written as Where The most general expression of the threshold voltage can be written as (14) is the substrate-bias (or body-effect) coefficient

The Threshold Voltage The threshold voltage expression given can be used both for n-channel and p-channel MOS transistors. But some of the terms and coefficients in this equation have different polarities for the n-channel (nMOS) case and for the p-channel (pMOS) case. The reason for this polarity difference is that the substrate semiconductor is p-type in an n-channel MOSFET and n-type in a p-channel MOSFET. The substrate Fermi potential is negative in nMOS, positive in pMOS. The depletion region charge densities and are negative in nMOS, positive in pMOS. The substrate bias coefficient is positive in nMOS, negative in pMOS. The substrate bias voltage is positive in nMOS, negative in pMOS. Typically, the threshold voltage of an enhancement-type n-channel MOSFET is a positive quantity, whereas the threshold voltage of a p-channel MOSFET is negative.

Threshold Voltage(Numerical Example)

The Threshold Voltage The exact value of the threshold voltage of an actual MOS transistor cannot be determined using (14) in most practical cases, due primarily to uncertainties and variations of the doping concentrations, the oxide thickness, and the fixed oxide-interface charge. The nominal value and the statistical range of the threshold voltage for any MOS process are ultimately determined by direct measurements, which will be described later. In most MOS fabrication processes, the threshold voltage can be adjusted by selective dopant ion implantation into the channel region of the MOSFET. For n-channel MOSFETs, the threshold voltage is increased (made more positive) by adding extra p-type impurities (acceptor ions). Alternatively, the threshold voltage of the n-channel MOSFET can be decreased (made more negative) by implanting n-type impurities (dopant ions) into the channel region

Substrate –bias Effect on Threshold Voltage It is seen that the threshold voltage variation is about 1.3 V over this range, which could present serious design problems if neglected. So the substrate-bias effect is unavoidable in most digital circuits and that the circuit designer usually must take appropriate measures to account for and/or to compensate for the threshold voltage variations.

Substrate –bias Effect on Threshold Voltage

MOSFET Operation: A Qualitative View Cross-sectional view of an n-channel (nMOS) transistor, (a) operating in the linear region, (b) operating at the edge of saturation, and (c) operating beyond saturation

Cross-sectional view of an n-channel (nMOS) transistor operating in the linear region

Cross-sectional view of an n-channel (nMOS) transistor operating at the edge of saturation

Cross-sectional view of an n-channel (nMOS) transistor operating beyond saturation

MOSFET Current-Voltage Characteristics The analytical derivation of the MOSFET current-voltage relationships for various bias conditions requires that several approximations be made to simplify the problem. Without these simplifying assumptions, analysis of the actual three-dimensional MOS system would become a very complex task and would prevent the derivation of closed form current-voltage equations.

MOSFET Current-Voltage Characteristics Cross-sectional view of an n-channel transistor, operating in linear region.

Gradual Channel Approximation(GCA) The gradual channel approximation (GCA) for establishing the MOSFET current-voltage relationships, effectively reduces the analysis to a one-dimensional current-flow problem. As in every approximate approach, however, the GCA also has its limitations, especially for small-geometry MOSFETs. Consider the cross-sectional view of the n-channel MOSFET operating in the linear mode, as shown in the figure. Here, the source and the substrate terminals are connected to ground, i.e., Vs = VB = 0. The gate-to-source voltage (VGS) and the drain-to-source voltage (VDS) are the external parameters controlling the drain (channel) current ID. The gate-to-source voltage is set to be larger than the threshold voltage VT0 to create a conducting inversion layer between the source and the drain.

Gradual Channel Approximation(GCA) The channel voltage with respect to the source is denoted by Vc(y). Assumption: The threshold voltage VT0 is constant along the entire channel region, between y = 0 and y = L. (In reality, the threshold voltage changes along the channel since the channel voltage is not constant) Assumption: The electric field component Ey along the y-coordinate is dominant compared to the electric field component Ex along the x-coordinate. (This assumption will allow us to reduce the current-flow problem in the channel to the y dimension only) The boundary conditions for the channel voltage Vc are: Assumption: The entire channel region between the source and the drain is inverted, i.e.,

MOSFET Drain Current Equation(GCA) The thickness of the inversion layer tapers off as we move from the source to the drain, since the gate-to-channel voltage causing surface inversion is smaller at the drain end. Simplified geometry of the surface inversion layer (channel region) Let QI(y) be the total mobile electron charge in the surface inversion layer. This charge can be expressed as a function of the gate-to-source voltage VGS and of the channel voltage Vc(y) as follows (15)

MOSFET Drain Current Equation(GCA) The incremental resistance dR of the differential channel segment can be expressed as (assuming constant surface mobility of all mobile electrons in the inversion layer) (16) The minus sign is due to the negative polarity of the inversion layer charge QI Applying Ohm's law for this segment yields the voltage drop along the incremental segment dy, in the y direction. (17)

MOSFET Drain Current Equation(GCA) Integrating along the Channel (18) (19) (20)

MOSFET Drain Current Equation(GCA) Equation (20) represents the drain current ID as a simple second-order function of the two external voltages, VGS and VDS. This current equation can also be rewritten as (21) or (22) where the parameters k and k' are defined as process transconductance parameter gain factor Current-voltage relationship is affected by to the process dependent constants k' , VT0, and is also affected by the device dimensions, W and L.

Region of Validity of the Equation The second-order current-voltage equation given above produces a set of inverted parabolas for each constant VGS value. The drain current-drain voltage curves shown above reach their peak value for VDS = VGS – VT0 Beyond this maximum, each curve exhibits a negative differential conductance, which is not observed in actual MOSFET current-voltage measurements (section shown by the dashed lines)

Validity of the Equation (Linear Region) We must remember now that the drain current equation (20) has been derived under the following voltage assumptions, which guarantee that the entire channel region between the source and the drain is inverted. This condition corresponds to the linear operating mode for the MOSFET Hence, the current equation (20) is valid only for the linear mode operation.

VDS~ ID Curve

Concept of Asymmetric Channel It is to be noted that the VDS measured relative to the source increases from 0 to VDS as we travel along the channel from source to drain. This is because the voltage between the gate and points along the channel decreases from VGS at the source end to VGS-VDS. When VDS is increased to the value that reduces the voltage between the gate and channel at the drain end to VT that is , VGS-VDS=VT or VDS= VGS-VT or VDS(sat) ≥ VGS-VT

MOSFET Current –Voltage Characteristics (Saturation Region) When VDS is increased to the value that reduces the voltage between the gate and channel at the drain end to Vt that is , VGS-VDS=VT or VDS= VGS-VT At this point the channel depth at the drain end decreases to almost zero, and the channel is said to be pinched off. Increasing VDS beyond this value has no effect on the channel shape. The MOSFET is said to have entered the saturation region, the drain current is essentially independent of VDS for constant VGS. VDSsat= VGS-VT Obviously, for every value of VGS≥VT, there is a corresponding value of VDSsat

Current Equation for Saturation Region Beyond the linear region boundary, i.e., for VDS values larger than VGS - VT0, the MOS transistor is assumed to be in saturation. Definition Condition for Saturation When (23) This expression indicates that the saturation drain current has no dependence on VDS

Channel Length Modulation

Channel Length Modulation The inversion layer charge at the source end of the channel is The inversion layer charge at the drain end of the channel is Note that at the edge of saturation, i.e., when the drain-to-source voltage reaches VDSAT, Consequently, the effective channel length (the length of the inversion layer where GCA is still valid) is reduced to Where is the length of the channel segment with QI = 0

Channel Length Modulation Since QI(y) = 0 for L’ < y < L, the channel voltage at the pinch-off point remains equal to VDSAT The gradual channel approximation is valid in this region; thus, the channel current can be written (24) Thus, (24) accounts for the actual shortening of the channel, also called channel length modulation. (25) The first term of this saturation current expression accounts for the channel modulation effect, while the rest of this expression is identical to (23).

Channel Length Modulation Since Empirically is an empirical model parameter, and is called the channel length modulation coefficient. Assuming that Equation (25) becomes (26)

Channel Length Modulation

Substrate Bias Effect