Packaging Design: Net This net is for an octagonal based prism. As with all technical drawings, the equipment goes a long way in helping you to draw a.

Slides:

Advertisements

Similar presentations

Isometric Drawing Part 1

Advertisements

Year 8 Design Technology 2 Point Perspective. Introduction Two point perspective is a 3D drawing with a horizon and two vanishing points. By using your.

The Picture Cube.

3 rd Angle Projection A 3 rd Angle projection is a 2D drawing of a 3D object. It shows three views the side, plan and end view. The side view is drawn.

Packaging Project Net construction This is an example of constructing a net of a complex shape (Hexagonal based pyramid) using a compass drawing equipment.

Ellipse – Trammel method

Learning Objective: To investigate the maths to do with parachutes.

Choose or draw a suitable A3 border sheet and start drawing. (do not draw the dimensions these are for guidance only)

Aberdeen Grammar School

Hexagons & Hexagonal Prisms. Hexagons Hexagons are 6 sided shapes. Hexagons can be dimensioned in 2 different ways. 1. Across the faces. 2. Across the.

Surface Area of Rectangular Prisms 1.How many outside surfaces does a rectangular prism have? 2.What shape are each of the faces? The six rectangular sides.

Aberdeen Grammar School Isometric Views. Isometric Drawings Lengths and breadths are drawn at 30° to the horizontal. Heights are drawn vertically. All.

PLANOMETRIC VIEW OF A KITCHEN.

Lesson Plan - APP Nets, Surface Area and Volume Mental and Oral Starter Pupils to update the ‘Heard the Word’ grid that they completed at the start of.

Pyramid Construction Pyramids Square Rectangle Hex Cone.

Making Here is the equipment you will most likely need to complete this unit of work. Although you may want to change these slightly e.g. you may want.

1.What are they? 2.Why do we need to draw them? 3.How do you draw them? 4.Exercises.

Summit Stock Cars Design Challenge: To design and construct a three or four wheeled vehicle. It will be launched down a ramp onto a flat surface, where.

Graphic Communication

Aberdeen Grammar School True Shapes The Cylinder.

Square Pyramid (cut). Cut Square Pyramid - Problem The given views show the Front Elevation and unfinished Plan of a cut square pyramid. Draw the following.

How to make a portrait template By Carlin Bright ACT-IED-8. Students will demonstrate use of proper line types a) Demonstrate the ability to perform a.

One Point Perspective One point perspective is a 3D drawing using one vanishing point on the horizon. Objects going into the distance arrive at the same.

Graphic Communication

ONOMATOPOEIA ART. WATCH THE CLIP BELOW FOR SOME IDEAS OF ONOMATOPOEIA WORDS

17/02/03Designed by Barry Forbes Graphic Communication Hexagons & Hexagonal Prisms.

Graphic Communication

Prisms & Cylinders Development with a cut surface 1 J. Byrne 2014.

Constructions and 3D Drawings. Constructing Perpendicular Bisectors - Perpendicular Bisectors are lines that cut each other in half at right angles.

Johnstone High School Graphic Communication Rectangular Pyramids

17/02/03Designed by Barry Forbes Graphic Communication Rectangular Pyramids.

Hexagons & Hexagonal Prisms.

True Shapes The Cylinder.  This type of drawing is asked to be drawn as part of a cut, prism, pyramid, cylinder or cone.  It shows the actual shape.

3 rd Angle Projection A 3 rd Angle projection is a 2D drawing of a 3D object. It shows three views the side view is drawn first. The plan view is drawn.

Design and technology st aidan’s high A pictorial sketch of a wall lamp is shown. The shade is in the form of a cut cone. Draw, from the given.

Lesson 7 Development of cones with a cut surface.

Constructing Triangles Tri 1 side/2 angles Constructions Example 1: To construct a triangle of base 9 cm with angles of 35 o and 65 o. To construct a.

Isometric Views.  Lengths and breadths are drawn at 30° to the horizontal.  Heights are drawn vertically.  All sizes are drawn to their exact sizes.

Cones.  Cones are shapes that have a circular base and come to one point at the top.

Cones. Cones are shapes that have a circular base and come to one point at the top.

Which shape column is the strongest?

PERSPECTIVE DRAWING. Step 1 Quarter the page as shown with light lines. Where the middle line touches the border mark two points - these are called....

True Shapes The Pyramid.  This type of drawing is asked to be drawn as part of a cut, prism, pyramid, cylinder or cone.  It shows the actual shape of.

Deans Community High School True Shapes The Pyramid.

Hexagonal Prisms Developments.  A development is a flat template of a 3D shape that when folded up in the correct way makes the actual shape of the 3D.

Draw the plan and the elevation of the cylinder, leaving 30mm between views Ø 40.

Graphic Communication

Coursework Warm-up Project

Basswood Lengths and Quantities 12” (305 mm) Bottom Horizontals

Cut lines Fold lines Glue tabs Different nets to produce a cube.

Shape and One Point Perspective Project

HEXAGONAL PRISM IN 60 UP 40 TOP BASE

LO To assess my understanding of transformations

Just What is Science?.

Shape & Space Surface Area.

ISOMETRIC CIRCLES AND CYLINDERS

Cut Hexagonal Prism Cut Hexagonal Prism - Question

Graphic Communication

Star Life Cycle Accordion Book

Graphic Communication

Cut Cones – What Are They?

BIO BOX 10 Points Skills Required: fold Instructions:

The Technological World

BIO BOX 10 Points Skills Required: fold Instructions:

Which shape column is the strongest?

Presentation transcript:

Packaging Design: Net This net is for an octagonal based prism. As with all technical drawings, the equipment goes a long way in helping you to draw a complicated shape with little measuring involved.

Use A3 Paper 1cm border, 1cm name bar, 2cm indent.

100mm/10cm

Draw a vertical centre line

20mm Measure 40mm either side of the centre line-this is one side of your Octagon 20mm

PARALLEL MOTION

40mm/4cm

PARALLEL MOTION 45 degree line

PARALLEL MOTION

Open your compass up to the length of one side of the octagon

PARALLEL MOTION Mark off this length along the horizontal line as shown

PARALLEL MOTION Repeat this for a total of 7 times

PARALLEL MOTION

10mm

PARALLEL MOTION 10mm 45 degree lines are drawn for the sides of the flaps

PARALLEL MOTION 10mm

PARALLEL MOTION

1. Home Work: Trace your net onto another sheet of A3. 2. Fill in a design with the theme on recycling using appropriate colours and designs. You can add a window to your design also.Remember do not colour in the glue tabs. 3. Cut out but do not assemble