GEM-P1632 Hybrid Control Communicator 8 zone expandable to 32 using keypad EZM’s, EZM4/8, EZM8, REC-V96 2 Area (Partition System) 32 user codes 2 zones 2-wire fire Supports up to 7 keypads 400 event logging 3 outputs

GEM-K1CA 32 Character LCD Display with large easy to read 4 Zone Expander Built-in Keypad Large Easy to Read Display Works on 1632, 9600 and 255

CONFIGURING The GEM-K1CA STEP 1: Move Jumper JP5 {located on the upper-right corner of the board} From pins 1-2 {Top} to 3-4 {Button} and wait approx. 45 Sec. Display will read XX OUT OF SYSTEM STEP 2: Enter code 11123 than press MENU once and proceed as Follows {repeating the following procedure for each keypad}

Keypad Beep ON Entry Sounder ON Keypad beep is on to turn off press ENTER Press MENU to continue or RESET to exit Entry sounder is on to Press MENU to Keypad Beep ON Entry Sounder ON

Keypad Address K P Address 01 If more than one keypad installed each must be assigned unique keypad address Keypads must be numbered consecutively Note: Only Keypad #1 can be used for programming Keypad Address K P Address 01

Keypad Address K P Address 01 Proceed as follows: Press MENU until “KP Address XX” displays Enter assigned number of keypad 01- 07 then press ENTER to save: a short beep will acknowledge a valid number Press MENU “New Compat #0000” displays Keypad Address K P Address 01 Note: In multiple area systems each keypad must be assigned an area see keypad assignments in program manual

New Compat # 0 0 0 0 Compatibility Number Compatibility number must remain at factory setting when used with 1632 controls. This feature is available for change only on the 9600 and 255 controls Press MENU EZM Address 01 displays

EZM Address 01 Enter EZM number 01- 06 using direct entry than press ENTER to save Press MENU Zone Response 00 displays The internal EZM in a GEM-K1CA can provide four additional zones EZM must be assigned unique address from 1 - 22 Note: GEM-K2S and GEM-K3DGTL DO NOT HAVE an EZM built in.

Zn Response 00 The normal loop response time of keypad EZM zones is 750ms. response can be reduced to 50ms as follows: Zn Response 00 1. zone 1 = 1 zone 2 = 2 zone 3 = 4 zone 4 = 8 2. Example: change zones 2,3&4 to 50mS response 3. zone 1 = 1 zone 2 = 2 zone 3 = 4 zone 4 = 8 total =15 Enter 15 into keypad using direct entry than press ENTER to save Press RESET to exit Config. Mode, display will read “01 OUT OF SYSTEM” Then replace jumper J5 across pins 1-2 {top two pins}

To Enter Dealer Program Mode Use Following Steps Enter 6 digit code (456789) Factory Step 2: Press Menu until Activate Program appears Step 3: Press Next/Yes to Enter Program Mode SYSTEM READY 01 / 28 / 99 03: 55PM ACTIVATE PROGRAM Yes / No

Easy Programming Question 1 Enter number of zones to be used in system Use number buttons 0-9 for direct entry Example 12 (Enter) Press ENTER to Save # OF ZNS IN AREA1 ENTER # ZONES __ __

Easy Programming Question #4 Question #2 2 - WIRE FIRE ZNS ENTER ZONE # ___ EZ ZONE DOUBLING ENABLED? Y/N Press YES or NO Press NEXT to proceed Enter YES (STAY) If zone doubling is desired NO (AWAY) for 1632 Question #5 Question #3 REPORT ALL ZONES TO CENTRAL? Y/N FIRE ZONES ENTER ZONE # ___ Enter YES to enable or NO to proceed Enter zone number(s) and Press ENTER to save than Press NEXT (STAY) to proceed

Easy Programming Question #8 24 HOUR ZONES ENTER ZONE # ___ ENTER/EXIT ZONES ENTER ZONE # ___ Enter Zone # & Press ENTER to save & Press NEXT to proceed Enter Zone # & Press ENTER to save & Press NEXT to proceed Question #9 Question #7 CHIME ZONES ENTER ZONE # ___ INTERIOR ZONES ENTER ZONE # ___ Enter Zone # & Press ENTER to save & Press NEXT to Proceed Enter Interior Zones #’s in system Press ENTER To Save & Press NEXT to proceed

Easy Programming AUX OUTPUT ZONES ENTER ZONE # ___ Question #12 50mS LOOP ZONES ENTER ZONE # ___ Question #10 CHIME 2 ZONES ENTER ZONE # ___ Enter Zone # & Press ENTER to save & Press NEXT to proceed Enter Zone # & Press ENTER to save & Press NEXT to proceed Question #13 Question #11 AUX OUTPUT ZONES ENTER ZONE # ___ EXIT/ENTRY2 ZONES ENTER ZONE # ___ Enter Zone # & Press ENTER to save & Press NEXT to Proceed Enter Zones # & Press ENTER to save & Press NEXT to proceed

Easy Programming ENABLE NO EOLR ZONES Y/N Question #16 AUTO BYP RENT ZN ENTER ZONE # ___ Question #14 SENSOR WATCH ZNS ENTER ZONE # ___ Enter Zone # & Press ENTER to save & Press NEXT to proceed Enter Zone # & Press ENTER to save & Press NEXT to proceed Question #17 Question #15 ENABLE NO EOLR ZONES Y/N KP SNDR ALRM ZNS ENTER ZONE # ___ Press YES to enable or NO to proceed Enter Zones # & Press ENTER to save & Press NEXT to proceed

Easy Programming # AREA 1 KEYPADS ENTER # KPS 01 Question #20 ENABLE SIA CP-0!? Y/N Question #18 ENABLE TELCO LINE TEST Y/N Press Yes to enable or NO to proceed Press YES to enable or NO to proceed Question #21 Question #19 # AREA 1 KEYPADS ENTER # KPS 01 ENABLE BURG OUT CHIRP Y/N Enter total number of Keypads press NEXT to proceed. Valid entries 01-07 Press YES to enable or NO to proceed

Easy Programming Question #22 CENTRAL PHONE # ____________________ Enter Telephone number of up to 16 digits Press [1] through [9] for digits 1-9 [*] [0] for Zero and [0] for a Blank * Press [*] [1] through [*][5] for Letters B-F Pre-Dial Delay = D ([*] [4]) Press ENTER to save and NEXT to proceed

Easy Programming Question #23 Question #24 CENTRAL STATION ACCOUNT #( _____ ) SEE WI FOR INFO RCVR FORMAT (0) Enter Account # Using direct entry Press ENTER to save & NEXT to proceed See WI for Receiver format type and 1 - 9 or *1 or *4 Press ENTER To Save than Press NEXT to proceed

Remember: U_ _ _ _ _ _ _ _ _ _ _ _ Enter user code User # User Code Options/Auth level U_ _ _ _ _ _ _ _ _ _ _ _ Enter user code Enter up to 32 user codes on 1632 with an authority level and access byte If necessary for each code Remember: PRESS ENTER TO SAVE EACH CODE BEFORE ENTERING NEXT CODE

U_01 _ 123 _ _ _ _ 1 _ _ Enter user code 1. Use MENU button to set the cursor to the User Number, than use Direct Entry to enter user number. 2. Press MENU to move cursor to User Code, than use Direct Entry to enter up to a 6 Digit Code. 3. Press MENU to move cursor to Option/Authority Level and Direct Entry to enter data. Note: { see program worksheet sec.2 for guidance in selecting entries.} >Enter sum of options in left nibble. >Enter authority level with any applicable arming options in right nibble Note: For entries greater then 9 *+0=A *+1=B *+2=C *+3=D *+4=E *+5=F

RF Transmitter Points Press MENU button to set cursor Enter the zone number (01-16) 816 (01-32) 1632 to which the transmitter will be mapped, the six digit RF ID # , 1 digit checksum number printed on the transmitter and the point # When programming the ID code number “A”= *0; “B”= *1; “C”= *2; “D”= *3; “E”= *4; “F”= *5 Press ENTER to save NEXT to continue ZN09 - 0 0 0 0 0 0 : 0 - - ZN# Xmit # + CS P

Enrolling Keyfobs Step1: Enter Keyfob transmitter number 01 to 08 Step2: Area # to which Keyfob is assigned Step3: Enter 6 digit RF ID# then 7th checksum digit after colon Step4: Aux-1 Options Aux-2 Options Note: See related programming worksheet Enrolling Keyfobs 01 - 1 9 8 6 4 2 2 : B 9B KF A XMIT # + CS OP

Zone Descriptions Screen 01 - _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ Use Keys 1 and 2 to move cursor left or right Use Keys 3 and 6 to select Characters Use ENTER Key to save description Use 0 Key to delete information To proceed to the next description move the cursor under the Zone Number {e.g. 01 } and change the Number using keys 3 and 6 than proceed and enter description for next Zone.

< 01 / 01 / 03 > Enter date Press NEXT to continue Date Entry Using direct entry Enter current date in the Format MM/DD/YY Than press ENTER key to save Press NEXT to continue

< 12 :15P > Enter Time Time Entry Using direct entry Enter current time in the format HH:MM:Am/Pm Select Am or Pm by Pressing any # Key press ENTER to save < 12 :15P > Enter Time You have now completed the custom default portion of the program. Press Reset Once to exit to the Address Program Mode for additional programming or Press Reset Twice to exit from programming and resume normal keypad operation

DEALER CODE 456789 DEALER CODE RE-ENTER Directly enter the new Dealer Code using 0-9 keys and Press Enter to save. DEALER CODE 456789 The Dealer code must be a Six Digit Code Re-Enter Dealer six Digit Code to verify the previous code and Press ENTER to save and NEXT to proceed DEALER CODE RE-ENTER

There are three types of address displays when Direct Address Program Mode Modifications through Direct Entry Programming allow you to Manually customize your Control Panel Options Panels will display Address Locations 0000 – 1198 Enter desired programmed data and Don`t forget to SAVE the data before moving onto next location There are three types of address displays when programming in the Direct Entry Program Mode (Binary, Decimal, Hexidecimal)

Settings such as Zone Features display and accept data Direct Address Program Mode BINARY (BIT) FORMAT Settings such as Zone Features display and accept data “Number” format. For example, Zone Features are turned on by pressing the key buttons 1 - 8 0000 - - - - - - - - B - 0730 1 2 3 - - 6 - - B

Example: Alarm Output Time Direct Address Program Mode DECIMAL FORMAT Settings such as Entry and Exit Delay times. Data is entered directly, by pressing keys 0-9 0000 - - - D Example: Alarm Output Time - 1183 0 0 5 D

by pressing keys 1-9, [*] [0] for zero and [*] [1] through Direct Address Program Mode HEXADECIMAL FORMAT Data such as Report Codes display and accept data by means of a Hexadecimal display. Data is entered directly, by pressing keys 1-9, [*] [0] for zero and [*] [1] through [*][5] for Hex B through F 0000 - - H Example: Chime Timeout set at 2 seconds - 0716 0 8 H

User Program Mode Only Keypad #1 may be used for programming, however it may be assigned to any area Program mode cannot be accessed while communicator is transmitting, except during first three minutes after power-up After entering a code or zone description, press ENTER to save before moving to next code or zone description Keypad in program mode for more than 4 minutes with no activity will activate steady sounder {press any key to silence or press Reset to exit

Accessing User Program Mode Enter a user code having the program option enabled Press MENU button once, than press BYPASS key three times “ACTIVATE PROGRAM” will display in keypad Press YES or ENTER User codes entered the same as in dealer program however in this mode “only the code is programmable” Authority level and Access-Control bytes can only be programmed in dealer program mode