KX-HTS Step by Step Guide SIP Phone in Existing Router December 21, 2016 Panasonic System Networks PBX SE team Specifications are subject to change without notice.

1. Overview SIP phone can be installed in LAN of existing router. Internet PSTN Office WAN Existing Router LAN:192.168.22.xxx WAN 192.168.22.99 for example L2 Switch LAN : 192.168.0.xxx KX-HTS 2

2. Table of Contents Chapter Contents 1 KX-HTS programming 2 KX-HDV without provisioning KX-NTV 3 KX-HDV with provisioning This document uses KX-NTV and KX-HDV for example. Provisioning supports data download from KX-HTS to KX-HDV for followings. Flexible key / PBX speed dial / Dialing plan and so on 3

Chapter 1 KX-HTS Programming

11. Assign Network Address of SIP Phone. Network address has to be assigned in Easy setup or Full programming mode. Internet LAN: 192.168.22.xxx WAN of KX-HTS 192.168.22.99 KX-HTS 5

12. Assign Network Address of SIP Phone. Network address has to be assigned in Easy setup or Full programming mode. Internet LAN: 192.168.22.xxx WAN of KX-HTS 192.168.22.99 KX-HTS 6

13. Disable Firewall. Firewall has to be disabled for KX-HDV with provisioning. When Firewall is enabled, HDV can not get time Information from HTS. Internet LAN: 192.168.22.xxx WAN of KX-HTS 192.168.22.99 KX-HTS 7

14. Assign SIP for extension. 114 is for KX-HDV and 115 is for KX-NTV for example. SIP Password has to be programmed. 8

15. Assign “Local”. Not “Remote” “Local” has to be assigned because not through internet. 9

16. Enable “Video Support”. Video has to be enabled if extension is KX-NTV, HDV430 or Bria. 10

17. Conditions All video terminals (KX-NTV, HDV430 or Bria) have to be installed to LAN of existing router only. Or all video terminals have to be installed to LAN o KX-HTS only, even if KX-HTS is connected to existing router. “Remote” has to be enabled for mixture (Both LAN of existing router and LAN of KX-HTS). When both “Local” and “Video” are assigned for both caller extension and called extension, KX-HTS applies P2P for both video and voice. WAN 192.168.22.99 for example Existing Router LAN:192.168.22.xxx L2 Switch LAN : 192.168.0.xxx KX-HTS 11

18. Remove the KX-HDV data from KX-HTS. If the KX-HDV was registered to other extension (102 for example), change port attribution of the extension from SIP to Analog SLT in order to remove SIP registration. Otherwise the KX-HDV cannot be used for chapter 2 and 3. KX-HDV phone also has to be initialized before registering. 12

Chapter 2 KX-HDV, KX-NTV w/o Provisioning

21. KX-HDV : Assign SIP Account. Other programming is same as step by step guide No.4. Internet Not extension number LAN: 192.168.22.xxx WAN of KX-HTS 192.168.22.99 KX-HTS Domain : 12.34.56.789 14

22. KX-NTV : Assign SIP Account. Other programming is same as step by step guide No.5. Internet Not extension number LAN: 192.168.22.xxx WAN of KX-HTS 192.168.22.99 KX-HTS Domain : 12.34.56.789 15

Chapter 3 KX-HDV with Provisioning

30. Overview of procedure Step1: check HTS configuration Check if following configuration are done. - Slide 11 (or 12) Assign Network Address of SIP Phone and, - Slide 13. Disable Firewall. Step2: Connect HDV to LAN of HTS and initialize Complete HDV provisioning at HTS LAN side. Step3: Change IP Addr and GW setting of HDV then move to HTS WAN Set following two parameters as static manually, - IP address: new address in LAN of the existing router - Default Gateway: IP address of HTS WAN port then connect to HTS WAN (LAN of the existing router) 17

31. Connect KX-HDV to LAN of KX-HTS at first. Step1 must complete. Then complete Step2 (this page). Frequency of dial tone and so on are customized automatically for your market. KX-HDV is assigned to extension 101 for example. WAN Existing Router LAN:192.168.22.xxx WAN 192.168.22.99 for example L2 Switch LAN : 192.168.0.xxx KX-HTS 18

32. Connect the KX-HDV to LAN of existing router. Step3: Change IP Addr and GW setting of HDV then move to HTS WAN IP address of the KX-HDV has to be static (Not DHCP client). Default GW of the KX-HDV has to be WAN address of KX-HTS. For example, IP address : 192.168.22.33 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.22.99 These can be set without PC. Existing Router LAN:192.168.22.xxx WAN 192.168.22.99 (example) L2 Switch LAN : 192.168.0.xxx KX-HTS Addr : 192.168.22.33 Mask : 255.255.255.0 GW : 192.168.22.99 19

33. Reference - 1 KX-HDV is programmed automatically as follows. 20

34. Reference - 2 KX-HDV is programmed automatically as follows. 21

35. Reference - 3 KX-HDV is getting time information from HTS LAN port address. 22

Thank you !

Revision Date No. Change Sept 26, 2016 All First official release Dec21, 2016 #13 Added a sentence about Firewall and time information #30 Added this page “Overview of procedure” #31 Added a line “Step1… Step2…” #32 Added a line “Step3…” Emphasized GW setting at HDV #35 Added this page “Reference-3” (NTP setting of HDV) 24