Before performing the operation check that all the components that will be sewn aren’t damaged, contaminated, or incorrectly cut, according to the S0123 Manual. F_I-CAL-002 V03 Assembly Components: Reaction Plan Stop Process, identify, and separate defective material Notify Supervisor and Quality Auditor PAGE 1 OF 2 Engineering Authorized by: _______________ Quality Authorized by: _______________ Production Authorized by: _______________ Tools ABC Madero Plant Operations: 1 Lock-stitch Needle 30-40/100mm. Revision Level: Panel A (1)3.- Webbing A (1) Safety glasses, scissors, stamp, scale. PLAN L Template 2.- Take a Webbing A from the holder, check that the material complies with S0123, if so, place it on the panel in the pin template, on top of the previous sub-assembly as shown in the image. Place the material that you already arranged under the presser foot as is shown Make the first straight seam starting approximately 10mm before the webbing, aligning the presser foot with the pin template. Finish the seam approximately 10 mm after the webbing. Sew 5 layers of material. Cut the threads. HONDA SZA RH Date Created 27/02/12 Date of Update/ Internal Revision Level 03/21/12 Int. Rev. 001 Op. 110 Sewing Webbing to Panel A Remove the template and begin the second straight seam approximately 10mm before the webbing, as is shown in the image. Use the presser foot to guide yourself. Finish approximately 10 mm after, cut the threads. Part No.: B 1.- Take a sub-assembly from operation 100, inspect that the part has the reinforcement union seam and doesn’t have any stitches that are broken, loose, nor any knots according to S0123, if it doesn’t then place the component on the pin template Use a scale to check at the beginning of each shift and every two hours that the distance from the center of the hole to the seam lines is from 9.5 to 15.5mm mm. 5 Needle thread: Coats Blue (style135) Bobbin thread: Coats Orange (style 135)

Before performing the operation check that all the components that will be sewn aren’t damaged, contaminated, or incorrectly cut, according to the S0123 Manual. F_I-CAL-002 V03 Assembly Components: Reaction Plan Stop Process, identify, and separate defective material Notify Supervisor and Quality Auditor PAGE 2 OF 2 Engineering Authorized by: _______________ Quality Authorized by: _______________ Production Authorized by: _______________ Tools ABC Madero Plant Operations: 1 Lock-stitch Needle de 30-40/100 mm. Revision Level : Panel A (1)3.- Webbing A (1) Safety glasses, scissors. PLAN L Template 6.- Check that both seams (on both sides) don’t have any loose, broken, or missing stitches or any abnormality according to S0123. Check that the components don’t have paper or pieces of extra fabric. HONDA SZA RH Date Created 27/02/12 Date of Update/ Internal Revision Level 03/21/12 Int. Rev. 001 Op. 110 Sewing Webbing to Panel A NOTES: The operation should be completed before leaving the part in the holder. The repairs should be performed immediately and following the “red bag” procedure. Review the checklist every two hours and use the scale to measure what the checklist indicates: A.Stitches per 100 mm : B.Distances between components : Distance from the seam to the edge of the reinforcement is from 9.5 to 15.5mm. 7.- If it meets the previous requirements, place the release stamp on the center of the webbing once the part is inspected and then place the part on the fixture as is shown. 7 Part No.: B 6 Needle thread: Coats Blue (style 135) Bobbin thread: Coats Orange (style 135)

LOG OF INTERNAL REVISION LEVELS OPERATION CARDS DATEEXTERNAL REVISION LEVEL INTERNAL REVISION LEVEL MODIFICATION PERFORMED PERSON RESPONSIBLE FOR MODIFICATION 03/21/ /21/12 Int. Rev. 001Revision ChangeAbril Perales F_F-ING-022 V01 Op. 110 Sewing Webbing to Panel A