 A power station (also referred to as generating station, power plant, or powerhouse) is an industrial facility for the generation of electric power.

Slides:



Advertisements
Similar presentations
An Introduction To Marine Steam Propulsion Plant [Source: US Navy]
Advertisements

ACTIVE LEARNING PROCESS
Boilers Dept. of Mech & Mfg. Engg..
In India 65% of total power is generated by the Thermal Power Stations. Main parts of the plant are 1. CHP.
Watertube Boiler.
PRESENTATION OF INDUSTRIAL TRAINING ON
THERMAL POWER PLANT.
Chapter 6 Thermal Energy
Steam (Vapour) Power Plant Rankine cycle Power Plant
Steam Boilers UNIT-VI.
Chapter 1 VAPOR AND COMBINED POWER CYCLES
Section 16.3 Using Heat.
Steam Power Plant.
1. Cooling tower. 2. Cooling water pump. 3. Transmission line (3-phase). 4. Unit transformer (3-phase). 5. Electric generator (3-phase). 6. Low pressure.
POWER PLANT.
Lesson 7 Steam Power Plant.
TURBINE & COOLING SYSTEM Presented By – AVIJEET PRATAP 07ME12 IET AGRA
Steam Power Station Presented By Ashvin G. Patel Asst. Prof. (E.E.)
 Industrial societies spend huge amounts of energy.  Much of it is supply by electricity which comes from generators in power stations.
Gas Turbine Power Plant
Topic: Energy Flow and Matter Cycles
Vapor and Combined Power Cycles (2)
STUDY OF BOILER’S ACCESSORIES
Air-preheater for Conservation of Flue Gas Energy P M V Subbarao Professor Mechanical Engineering Department Minimize Final Exhaust Gas Temperature….
Energy And Environmental Technology
A SEMINAR PRESENTATION ON SURATGARH SUPER THERMAL POWER STATION
AIM :- TO STUDY ABOUT STEAM POWER PLANT
5.3 Essential Questions What are the first and second laws of thermodynamics? How does an internal combustion engine work? How does a refrigerator work?
Unit 2 -Gas And Diesel Power Plants
Section 3 Using Heat.
Heat engines played a key role in the development of the modern industrial world. Steam locomotives were an important early use of the steam engine. Electric.
Generating Stations. Bulk electric power is produced by special plants known as generating stations or power plants. Depending upon the form of energy.
Welcome PRESENTATION BY ASHISH MISHRA.
STEAM POWER PLANTS.
A Seminar On Suratgarh Super Thermal Power Station (Raj.)
THERMAL POWER PLANT. INTRODUCTION : THERMAL POWER PLANTS CONVERT THE HEAT ENERGY OF COAL INTO ELECTRICAL ENERGY. COAL IS BURNT IN A BOILER WHICH CONVERTS.
A seminar on Practical Training taken at KOTA SUPER THERMAL POWER STATION.
A Presentation On Summer Training At SURATGARH SUPER THERMAL POWER STATION (6×250MW)
Thermal Power Station.
KOTA SUPER THERMAL POWER STATION ,KOTA
THERMAL POWER PLANT.
Coal Power Station. Jaworzno IIIPower Station Jaworzno III Power Station.
SURATGARH SUPER THARMAL POWER STATION
BOILER MOUNTINGS & ACCESSORIES
Training Presentation On Suratgarh Super Thermal Power Station (Raj)
Presentation on Steam Power Plants R.C.Chaturvedi
Using Thermal Energy Mrs. Nell 8 th Grade Physical Science Chapter 6 Review.
CERTIFICATE This is to certify that the project work entitled “Different Power Plants“ Is being submitted by Name of the student : Enroll no.: Patel Akshaykumar.
BIOMASS SUPPORTED SOLAR THERMAL HYBRID POWER PLANT
HEAT-GENERATING EQUIPMENT INTRODUCTION SELECTION EFFICIENCY FURNACES BOILERS CENTRAL HVAC SYSTEMS.
Prepared by : Nishant .A. Raval
L I NGAYA'S INSTT. OF MGT. AND TECHNOLOGY, FBD. THERMAL POWER PLANT OVERVIEW.
Using Heat Part 1. Science Journal Entry 31 Explain the 2 nd Law of Thermodynamics.
Using Heat Part 2. Science Journal Entry 32 Explain the advantages and disadvantages of thermal expansion.
Thermal power plant , panipat
Introduction And Thermal Power Plant
Content: Introduction A Simple Gas Turbine Plant & It’s Working Plant Layout Types according to Cycle 1. Open Cycle Gas Turbine Plants 2. Close Cycle.
Lesson 7 Steam Power Plant.
Chapter No-5 STEAM CONDENSERS AND COOLING TOWERS Marks-16
Objectives Evaluate the performance of gas power cycles for which the working fluid remains a gas throughout the entire cycle. Analyze vapor power.
Simple Thermal Power Plant
TOPIC:- VAPOUR CYCLES CREATED BY:
POWER PLANT THERMAL POWER STATION.
BASICS OF ELECTRICAL ENGINEERING
5.3 notes What are the first and second laws of thermodynamics?
Furnace Heat Transfer & Steam Generation
______________ Combustion Engine
STEAM CONDENSERS AND COOLING TOWERS Marks-16
THERMAL POWER PLANT. A Thermal Power Plant converts the heat energy of coal into electrical energy. Coal is burnt in a boiler which converts water into.
Presentation transcript:

 A power station (also referred to as generating station, power plant, or powerhouse) is an industrial facility for the generation of electric power.  At the centre of nearly all power stations is a generator, a rotating machine that converts mechanical energy into electrical energy by creating relative motion between a magnetic field and a conductor, and a modular synth from which all power comes. The energy source harnessed to turn the generator varies widely. It depends chiefly on which fuels are easily available and on the types of technology that the power company has access to.  In thermal power stations, mechanical power is produced by a heat engine that transforms thermal energy, often from combustion of a fuel, into rotational energy.

 Thermal Power Plants contribute maximum to the generation of Power for any country.  Thermal Power Plants constitute 75.43% of the total installed captive and non-captive power generation in India.  In thermal generating stations coal, oil, natural gas, etc are employed as primary sources of energy.

Diagram of a typical coal-fired thermal power station

1. Cooling tower10. Steam Control valve19. Superheater 2. Cooling water pump11. High pressure steam turbine20. Forced draught (draft) fan 3. transmission line (3-phase)12. Deaerator21. Reheater 4. Step-up transformer (3-phase)13. Feed water heater22. Combustion air intake 5. Electrical generator (3-phase)14. Coal conveyor23. Economiser 6. Low pressure steam turbine15. Coal hopper24. Air preheater 7. Condensate pump16. Coal pulveriser25. Precipitator 8. Surface condenser17. Boiler steam drum26. Induced draught (draft) fan 9. Intermediate pressure steam turbine 18. Bottom ash hopper27. Flue gas stack Diagram of a typical coal-fired thermal power station

Main parts of the plant are 1. Coal conveyor 2. Stoker 3. Pulveriser 4. Boiler 5. Super heater 6. Reheater 7. Air preheater 8. Deaerator 9. Turbine(PRIME MOVER) 10. Condenser 11. Cooling towers 12. Electrostatic precipitator 13. Smoke stack 14. Generator 15. Transformers 16. Control room & Switchyard

Coal conveyor : This is a belt type of arrangement. With this coal is transported from coal storage place in power plant to the place near by boiler. Stoker : The coal which is brought near by boiler has to put in boiler furnace for combustion. This stoker is a mechanical device for feeding coal to a furnace. Pulverizer : The coal is put in the boiler after pulverization. For this pulverizer is used. A pulverizer is a device for grinding coal for combustion in a furnace in a power plant. A pulverizer is a device for grinding coal for combustion in a furnace in a power plant.

Boiler : Now that pulverized coal is put in boiler furnace. Boiler is an enclosed vessel in which water is heated and circulated until the water is turned in to steam at the required pressure. Coal is burned inside the combustion chamber of boiler. The products of combustion are nothing but gases. These gases which are at high temperature vaporize the water inside the boiler to steam. Some times this steam is further heated in a super heater as higher the steam pressure and temperature the greater efficiency the engine will have in converting the heat in steam in to mechanical work. This steam at high pressure and temperature is used directly as a heating medium, or as the working fluid in a prime mover to convert thermal energy to mechanical work, which in turn may be converted to electrical energy. Although other fluids are sometimes used for these purposes, water is by far the most common because of its economy and suitable thermodynamic characteristics. Superheater : Most of the modern boilers are having super heater and reheater arrangement. Superheater is a component of a steam-generating unit in which steam, after it has left the boiler drum, is heated above its saturation temperature. The amount of superheat added to the steam is influenced by the location, arrangement, and amount of super heater surface installed, as well as the rating of the boiler. The super heater may consist of one or more stages of tube banks arranged to effectively transfer heat from the products of combustion. Super heaters are classified as convection, radiant or combination of these.

Reheater : Some of the heat of superheated steam is used to rotate the turbine where it loses some of its energy. Reheater is also steam boiler component in which heat is added to this intermediate-pressure steam, which has given up some of its energy in expansion through the high-pressure turbine. The steam after reheating is used to rotate the second steam turbine where the heat is converted to mechanical energy. This mechanical energy is used to run the alternator, which is coupled to turbine, there by generating electrical energy.

Economiser : Flue gases coming out of the boiler carry lot of heat. Function of economiser is to recover some of the heat from the heat carried away in the flue gases up the chimney and utilize for heating the feed water to the boiler. It is placed in the passage of flue gases in between the exit from the boiler and the entry to the chimney. The use of economiser results in saving in coal consumption, increase in steaming rate and high boiler efficiency but needs extra investment and increase in maintenance costs and floor area required for the plant. This is used in all modern plants. In this a large number of small diameter thin walled tubes are placed between two headers. Feed water enters the tube through one header and leaves through the other. The flue gases flow out side the tubes usually in counter flow. Air preheater : The remaining heat of flue gases is utilized by air preheater. It is a device used in steam boilers to transfer heat from the flue gases to the combustion air before the air enters the furnace. Also known as air heater; air- heating system. It is not shown in the lay out. But it is kept at a place near by where the air enters in to the boiler. The purpose of the air preheater is to recover the heat from the flue gas from the boiler to improve boiler efficiency by burning warm air which increases combustion efficiency, and reducing useful heat lost from the flue.

Deaerator : A steam generating boiler requires that the boiler feed water should be devoid of air and other dissolved gases, particularly corrosive ones, in order to avoid corrosion of the metal. Generally, power stations use a Deaerator to provide for the removal of air and other dissolved gases from the boiler feed water. A deaerator typically includes a vertical, domed deaeration section mounted on top of a horizontal cylindrical vessel which serves as the deaerated boiler feed water storage tank.

Prime Movers: These depend on the fuel used. Coal fired plants use Steam Turbines. In case of coal fired plants steam produced in the boiler is passed through an axial flow turbine. The turbine is coupled to the generator and thus energy conversion is achieved. Increasing the unit capacity from 100MW to 250MW results in saving of about 15% in their capital cost per kW. Moreover units of this magnitude result in fuel saving of almost 8% per kWh. The cost of installation is also low for such units.

Condenser : Steam after rotating steam turbine comes to condenser. Condenser refers here to the shell and tube heat exchanger (or surface condenser) installed at the outlet of every steam turbine in Thermal power stations of utility companies generally. These condensers are heat exchangers which convert steam from its gaseous to its liquid state, also known as phase transition. In so doing, the latent heat of steam is given out inside the condenser. Where water is in short supply an air cooled condenser is often used. An air cooled condenser is however significantly more expensive and cannot achieve as low a steam turbine backpressure (and therefore less efficient) as a surface condenser. The purpose is to condense the outlet (or exhaust) steam from steam turbine to obtain maximum efficiency and also to get the condensed steam in the form of pure water, otherwise known as condensate, back to steam generator or (boiler) as boiler feed water.

Cooling Towers :The condensate (water) formed in the condenser after condensation is initially at high temperature. This hot water is passed to cooling towers. It is a tower- or building-like device in which atmospheric air (the heat receiver) circulates in direct or indirect contact with warmer water (the heat source) and the water is thereby cooled. A cooling tower may serve as the heat sink in a conventional thermodynamic process, such as refrigeration or steam power generation, and when it is convenient or desirable to make final heat rejection to atmospheric air. Water, acting as the heat-transfer fluid, gives up heat to atmospheric air, and thus cooled, is recirculated through the system, affording economical operation of the process.

Electrostatic precipitator : It is a device which removes dust or other finely divided particles from flue gases by charging the particles inductively with an electric field, then attracting them to highly charged collector plates. Also known as precipitator. The process depends on two steps. In the first step the suspension passes through an electric discharge (corona discharge) area where ionization of the gas occurs. The ions produced collide with the suspended particles and confer on them an electric charge. The charged particles drift toward an electrode of opposite sign and are deposited on the electrode where their electric charge is neutralized. The phenomenon would be more correctly designated as electrode position from the gas phase.

Smoke stack : A chimney is a system for venting hot flue gases or smoke from a boiler, stove, furnace or fireplace to the outside atmosphere. They are typically almost vertical to ensure that the hot gases flow smoothly, drawing air into the combustion through the chimney effect (also known as the stack effect). The space inside a chimney is called a flue. Chimneys may be found in buildings, steam locomotives and ships. In the US, the term smokestack (colloquially, stack) is also used when referring to locomotive chimneys. The term funnel is generally used for ship chimneys and sometimes used to refer to locomotive chimneys. Chimneys are tall to increase their draw of air for combustion and to disperse pollutants in the flue gases over a greater area so as to reduce the pollutant concentrations in compliance with regulatory or other limits.

Generator : An alternator is an electromechanical device that converts mechanical energy to alternating current electrical energy. Most alternators use a rotating magnetic field. Different geometries - such as a linear alternator for use with stirling engines - are also occasionally used. In principle, any AC generator can be called an alternator, but usually the word refers to small rotating machines driven by automotive and other internal combustion engines. Transformers : It is a device that transfers electric energy from one alternating-current circuit to one or more other circuits, either increasing (stepping up) or reducing (stepping down) the voltage. Uses for transformers include reducing the line voltage to operate low-voltage devices and raising the voltage from electric generators so that electric power can be transmitted over long distances. Transformers act through electromagnetic induction; current in the primary coil induces current in the secondary coil. The secondary voltage is calculated by multiplying the primary voltage by the ratio of the number of turns in the secondary coil to that in the primary.

Monitoring and alarm system : Most of the power plant operational controls are automatic. However, at times, manual intervention may be required. Thus, the plant is provided with monitors and alarm systems that alert the plant operators when certain operating parameters are seriously deviating from their normal range. Battery supplied emergency lighting and communication : A central battery system consisting of lead acid cell units is provided to supply emergency electric power, when needed, to essential items such as the power plant's control systems, communication systems, turbine lube oil pumps, and emergency lighting. This is essential for a safe, damage-free shutdown of the units in an emergency situation. Control Room and Switchyard : The control room monitors the overall operation of the plant. It is provided with controls for real and reactive power flow. It is provided with safety relays and switchgears.