1. 1 IKCO Samand Suspension System Presentation

2. 2 Samand Table of Contents... Wheel and Tire Front Suspension Rear Suspension Steering Brakes

3. 3 Wheels : (Standard) :Steel 6J15 (Optional) : Aluminimum6.5J15 Aluminimum6.5J15(ITAL speed) Aluminimum6.5J15(Sorbet) Tiers : 185//65 R15 88H Falken tire :185/65 R15 88H Slncera SN-816 Optional Bridgestone tire : 185/65 R15 88H B391 Optional Pirelli tire : 185/65 R15 P6000 Optional Continental tire : 185/65 R15 88H Optional Goodyear tire : 185/65 R15 Samand Wheel and Tire… Description

4. 4 Samand Front Suspension… Description 1. Suspension assembly: The independent front suspension is of the MacPherson strut type, incorporating coil springs and integral telescopic shock absorbers. The Macpherson struts are located by transverse lower suspension arms. which utilize rubber inner mounting bushes.

5. 5 Samand 1 4 5 6 3 2 ( 1 ) Suspension strut assembly. ( 2 ) Front hub carrier assembly. ( 3 ) Lower suspension arm. ( 4 ) Anti-roll bar. ( 5 ) Anti-roll bar drop links. ( 6 ) Front suspension sub frame. Front Suspension… Description 1. Suspension assembly:

6. 6 Samand ( 4 ) Suspension strut top mounting nuts. Front Suspension… Description 4 4

7. 7 ( 9 ) Washer. (10) Rubber gaiter. (11) Stop bump. Samand Front Suspension… Description 2. Spring and damper: 9 11 10 14 13 12 15 16 (12) Mounting plate. (13) Rubber buffer. (14) Upper dished plate. (15) Lower dished plate. (16) Upper spring seat.

8. 8 Samand Place bottom of strut into top of hub carrier ensuring location of guide into slot. This ensures correct angular position and as a stop. Front Suspension… Description 3. Strut:

9. 9 Samand Front Suspension… Description 4. Hub: Important: Grease the nut contact face and threads with universal grease before applying correct torque.

10. 10 Samand Front Suspension… Description 5. Wishbone: Wishbone

11. 11 Samand Press on bush to align A and B (ignore mark C). Front Suspension… Description 5. Wishbone: C A B

12. 12 Samand ( 1 ) Drop link. ( 2 ) Bolt. ( 3 ) Bolt and nut. Note: Drop links are supplied as an assembly. The bushes are not renewable. Front Suspension… Description 6. Drop link: 3 1 2

13. 13 Samand On completion check anti-roll bar adjustment see adjustments front suspension. Front Suspension… Description 7. Anti-roll bar:

14. 14 Samand Front Suspension… Description 8. Sub frame: ( 9 ) Plastic plugs and bolts. (10) Bolts. (11) Sub frame. 11 10 9 9

15. 15 Track + =Toe-in Track - =Toe-out Track +1°± 0.05' Caster 3°± 30' Front Camber 0°± 30' Rear Camber -1.2°± 30' Pivot angle 11.30°± 30' Height Normal suspension H1=141mm Raised suspension H1=159mm Samand Front Suspension… Description 9. Suspension geometry:

16. 16 Samand Front Suspension… Special Tools

17. 17 Samand Rear Suspension… Description 1. Suspension assembly: The rear suspension is of the semi-independent trailing arm type, which consists of two trailing arms, linked by a tubular cross member. A torsion bar is fitted transversely between each trailing arm and the opposite suspension side member. An anti-roll bar is fitted between the trailing arms. The complete rear axle assembly is mounted onto the vehicle underbody via four rubber mountings.

18. 18 Samand Rear Suspension… Description 1. Suspension assembly: 4 1 6 2 3 5 7 8 9 ( 1 ) Trailing arm. ( 2 ) Tubular cross member. ( 3 ) Right hand torsion bar ( identification 1 paint ring ). ( 4 ) Left hand torsion bar ( identification 2 paint rings ). ( 5 ) Suspension side member. ( 6 ) Anti-roll bar. ( 7 ) Shock Absorber. ( 8 ) Front rubber mountings. ( 9 ) Rear mounting.

19. 19 Rear Suspension… Description 1. Suspension assembly: Samand 1 3 4 2 2 4 7 8 5 ( 1 ) Rear hub nut. ( 2 ) Shock absorber. ( 3 ) Anti-roll bar clamp bolts. ( 4 ) Torsion bars (stop bolts). ( 5 ) Front mounting to suspension. ( 6 ) Front suspension mounting to body ( 7 ) Rear mounting to suspension. ( 8 ) Rear suspension mounting to body.

20. 20 Samand Position the new flexible bushes so that the openings are in parallel to the vehicle centre line. NEVER hit the flexible bush support. Rear Suspension… Description 2. Cross arm:

21. 21 Samand When refitting torsion bars DO NOT REVERSE BARS. a Right hand: 1 paint ring. b Left hand: 2 paint rings. Rear Suspension… Description 3. Torsion bar: b a

22. 22 Samand ( 3 ) Nut and washer from upper shock absorber and nut from lower fixing. ( 4 ) Shock absorber. Rear Suspension… Description 4. Damper: 3 4 3

23. 23 Samand ( 2 ) Inner bearing race. ( 4 ) Hub. ( 5 ) Outer bearing race. ( 6 ) Thrust washer and hub retaining nut. Rear Suspension… Description 5. Hub: 2 4 5 6

24. 24 Samand Rear Suspension… Special Tools

25. 25 Samand The steering gear is mounted onto the front sub frame, and is connected by two track rods, with ball joints at their outer ends, to the steering arms projecting rearwards from the swivel hubs. The track rod ends are threaded, to facilitate adjustment. The hydraulic power steering system is powered by a belt-driven pump, which is driven off the crankshaft pulley. Steering… Description 1. Steering assembly:

26. 26 Samand ( 1 ) Steering wheel ( 2 ) Track rod end ( 3 ) Steering gear Assy ( 4 ) Control value ( 5 ) Intermediate shaft ( 6 ) Steering column. 2 3 4 5 6 1 Steering… Description 1. Steering assembly:

27. 27 Samand The power-assisted steering gear is of the rack and pinion type consisting of control valve and servo cylinder in a common housing. Together with the power steering pump and power steering fluid reservoir, these are the main components of the system. Power steering fluid is pumped from the power steering pump to the control valve where, depending on which way the steering wheel is turned, it is directed to either the right or the left side of the servo cylinder. Steering… Description 1. Steering assembly:

28. 28 Samand ( 1 ) Power steering fluid reservoir. ( 2 ) Power steering pump. ( 3 ) Control valve. ( 4 ) Servo cylinder. 4 2 3 1 Steering… Description 1. Steering assembly:

29. 29 Turning radius :5.5 m Steering wheel lock to lock :3.13 turn Front wheel toe setting :1°±0.05’ or 5.0- 6.0mm Pump pressure :95-105 bar Capacity of system :1 lit. Fluid type: ATF Dextron II-d Samand Steering… Description

30. 30 Samand The level varies according to temperature. The level must be set with engine off, the wheels straight ahead and after the fluid is free from air bubbles. The fluid level must be between filling marks on reservoir. Steering… Description 2. Oil level:

31. 31 Samand ( 7 ) Output regulator piston, gauze, ball, seal and spring. ( 8 ) Take-off hole. 7 8 Steering… Description 3. Pump regulator:

32. 32 Samand ( 8 ) Control valve to housing bolts. Steering… Description 4. Distribution valve: 8

33. 33 Samand Steering… Description 5. Rack damper : 10 9 8 7 6 5 4 ( 4 ) O Ring. ( 5 ) Adjusting shims. ( 6 ) Flexible Shims. ( 7 ) Washer. ( 8 ) Cup. ( 9 ) Spring. (10) Thrust Button.

34. 34 Samand ( 8 ) Control valve to housing bolts. Steering… Description 4. Steering gear: 5 4

35. 35 Samand The track rod ends on both sides are screwed on the track rods and secured by means of locknuts. By slackening the locknuts and turning the track rods to left or right, the distance between the outer and inner track rod ends can be reduced or increased to adjust the toe-in angle. Each track rod is secured to the steering arm of the steering swivel member by means of a self-locking nut. The track rod ends cannot be dismantled. Steering… Description 7. Steering arm:

36. 36 Samand ( 6 ) Track rod ball joint nut. ( 7 ) Track rod lock nut. Steering… Description 8. Track adjustment : 7 6

37. 37 Samand Steering wheel lock to lock 3.13 turns Turning circle 11 meters Front wheel toe setting 1.0 + 0.5 toe-in Pump pressure at fast idle 95 - 105 bars Capacity of system 1 Liter Fluid type ATF Dextron ii-D Steering… Description 9. General precautions :

38. 38 Excerpt taken from the SAMAND LX Owner’s Handbook Samand Steering… Description 10. Service Maintenance:

39. 39 Samand Steering… Special Tools

40. 40 Samand The braking system is of the servo-assisted hydraulic type. The vehicle has disc brakes on the front wheels which are Girling type. Drum brakes are fitted to the rear wheels which are also Girling type. These rear brakes incorporate leading, tracking shoes and these are activated by twin piston wheel cylinders. The wheel cylinders have integral pressure regulating valves which control the hydraulic pressure applied to the rear wheels. The regulating valves help prevent rear wheels lock-up during emergency braking, a self adjust mechanism is incorporated to automatically compensate for brake shoe wear. As the brake shoes wear, the foot-brake operation automatically operates the adjuster mechanism which effectively lengthens the shoe strut and repositions the brake shoes to remove the lining to drum clearance. Brakes… Description 1. Brake assembly:

41. 41 Samand Brakes… Description 2. Master pump: 7 9 8 ( 7 ) Plastic retaining strap. ( 8 ) Reservoir. ( 9 ) Master cylinder.

42. 42 Samand Brakes… Description 3. Brake servo unit:

43. 43 Samand Brakes… Description 4. Front brake (brake calliper): 2 3 1 4 6 5 7 8 ( 1 ) Mounting bracket bolt. ( 2 ) Bleed screw. ( 3 ) Calliper body. ( 4 ) Mounting bracket. ( 5 ) Guide pin. ( 6 ) Guide pin screw. ( 7 ) Guide pin dust cover. ( 8 ) Brake pads.

44. 44 Samand Brakes… Description 4. Front brake (brake calliper): 8 7 9 6 ( 6 ) Seal around piston. ( 7 ) Cap. ( 8 ) Bellows. ( 9 ) Disc.

45. 45 Samand Brakes… Description 5. Front brake (brake pad): D D. Brake pad minimum thickness: 2.0mm

46. 46 Samand Brakes… Description 6. Front brake (ventilated disc): B A C Type: Ventilated disc A. Disc diameter: 266mm B. Disc thickness New: 20.4mm Minimum disc thickness: 18.0mm C. Maximum disc run-out: 0.07mm

47. 47 Samand Brakes… Description 7. Rear brake (hub-drum): 1 2 9 8 3 6 4 5 5 5 7 ( 1 ) Drum. ( 2 ) Leading screw. ( 3 ) Trailing screw. ( 4 ) Adjuster strut. ( 5 ) Retaining pin spring and spring clip. ( 6 ) Wheel cylinder. ( 7 ) Bleed screw. ( 8 ) Handbrake lever. ( 9 ) Back plate.

48. 48 Samand Brakes… Description 7. Rear brake (hub-drum): A B Drum internal diameter: New: 228.6mm A. Maximum diameter after machining: 229.6mm B. Brake shoe lining minimum thickness: 1.0mm

49. 49 Samand Sequence must be followed to ensure the removal of all air from the system. Conventional braking system A) Right-hand rear wheel. C) Left-hand rear wheel. B) Left-hand front wheel. D) Right-hand front wheel. Brakes… Description 8. Bleeding: A C B D

50. 50 Samand ( 1 ) Handbrake lever assembly. ( 2 ) Handbrake warning switch. ( 3 ) Primary cable. ( 4 ) Secondary cables (left and right). ( 5 ) Cable bracket. ( 6 ) Bracket strap. Brakes… Description 9. Hand brake: 1 3 4 2 6 5 4

51. 51 IKCO Samand … The End Questions ?