1. DVG-G5402SP D-Link VoIP Wireless Router
DRS Marketing – 02 Jan 2008

2. Agenda Product Overview DVG-G5402SP Key Features Hardware Description
Web GUI Site Map
DVG-G5402SP Setup
Internet Set up with Cable Modem
Setting Up Wireless SSID & Security
Setting Up Wireless MAC filtering
Save and Reboot
Troubleshooting
Device Status & Statistics
Reset Factory Default
Questions and Answers

3. Product Overview
The DVG-G5402SP is designed to carry both voice and fax over the IP network and wirelessly share Internet access.
It uses the industry standard SIP call control protocol so as to be compatible with free registration services or VoIP service providers’ systems. As a standard user agent, it is compatible with all common Soft Switches and SIP proxy servers.
The DVG-G5402SP can be seamlessly integrated into an existing network by connecting to a phone set and fax machine. With only a broadband connection such as an ADSL bridge/router or a Cable Modem, the VoIP Router allows you to use voice and fax services over IP in order to reduce the cost of all long distance calls.
The DVG-G5402SP is also an b/g wireless access point. Allow wireless clients to connect to it and share your broadband Internet connection. A built-in 4-port switch makes it possible to connect up to 4 Ethernet-enabled computers or devices to also share your Internet connection.

4. DVG-G5402SP Key Features Internet Telephone
2 FXS Ports for Phones+1 PSTN (Life Line)
SIP Protocol
Convenient Call Feature Support
Guaranteed Voice Quality With QoS
WAN/LAN Connection
10/100Mbps Ethernet WAN Port
4 10/100Mbps Ethernet LAN Ports
802.11g WLAN (Up to 54Mbps Wireless Speed)
PPPoE Dial-Up Broadband Support
Page 4 4

5. DVG-G5402SP Key Features Built-in Router
DHCP Server for Automatic IP Assignment
IP Sharing for Multiple Users Internet Access Via Single IP (NAT)
IPSec/PPTP VPN Pass-Through
Configuration/Management
Easy Installation With GUI Support
Auto provisioning Using TFTP Encryption/ Authentication
Remote Firmware Update via TFTP/FTP/HTTP

6. Hardware Description – Front Panel
Page 6

7. Hardware Description – Front Panel
Power: Power LED. A steady light indicates a proper connection to a power source.
Prov./Alm.: A blinking light indicates the VoIP Router is attempting to connect with the Provisioning server. Once the service connects, the LED will turn off. The LED will light solid if the self-test or boot-up fails.
Register: The Register LED will turn on when the VoIP Router is connected to a VoIP service provider. The LED will be blinking if not connected to a service provider.
WAN: When a connection is established the 10 or 100 LED will light up solid. The LED will blink to indicate
Page 7

8. Hardware Description – Front Panel
WLAN: A steady light indicates a wireless connection. A blinking light indicates that the VoIP Router is receiving/transmitting from/to the wireless network.
LAN: When a connection is established the 10 or 100 LED (bottom) will light up solid on the appropriate port. The LEDs will blink to indicate activity. If the 10 or 100 LED does not light up when a cable is connected, verify the cable connections and make sure your devices are powered on.
Phone: This LED displays the VoIP status and Hook/Ringing activity on the phone port that is used to connect your normal telephone(s). If a phone connected to a phone port is off the hook or in use, this LED will light solid. When a phone is ringing, the indicator will blink.
Line: Light on means the line is in use (off-hook), and vice versa.
Page 8

9. Hardware Description – Rear Panel
Page 9

10. Hardware Description – Rear Panel
Line: Connect to your original telephone line on the wall jack with RJ-11 cable.
Phone Port (1-2): Connect to your phones using standard phone cabling (RJ-11).
LAN: Connect to your Ethernet enabled computers using Ethernet cabling.
WAN: Connect to your broadband modem using an Ethernet cable.
Power Receptor: Receptor for the provided power adapter.
Ground: A conducting connection with the earth. Connect with the ground so as to make the earth a part of an electrical circuit using metal wire.
Antenna: Connect to a wireless network.
WARNING:
DO NOT (1) connect the phone ports to each other (FXS to FXS) or
(2) connect any phone port directly to a PSTN line (FXS to PSTN) or
to an internal PBX line (FXS to PBX extension).
Doing so may damage your VoIP Router.
Page 10

11. Hardware Description – Bottom Label
Page 11

12. Web GUI Site Map
Page 12

13. Setting Up DVG-G5402SP DVG-G5402SP
Step 1. Please ensure that the cable modem is power off. Connect the Ethernet cable from the WAN port of DVG-G5402SP to the cable modem. Then connect the Ethernet cable from your PC into any of the LAN ports on the DVG-G5402SP
LAN Port
WAN Port
Analog Phone
Cable Modem PC
Page 13

14. Setting Up DVG-G5402SP
Step 2. Next, power up the cable modem first followed by the router.   
Step 3. Open up a web browser and enter in the address\URL field. You will see the log in page. Type “User” as the user name and leave the password field empty. Click on the “Login” button.
Page 14

15. Setting Up DVG-G5402SP
Step 4. Select “Setup” tab from the navigation menu and click on “Internet Setup”.
Internet Connection type should be selected as “DHCP” and “Auto” for DNS server.
Page 15

16. Setting Up DVG-G5402SP
Step 5. Select “Status” tab from the navigation menu and click “Device Info”
Step 6. Check the “WAN Port Information” section to see if you have obtained a DHCP IP address and DNS leased from the cable modem successfully.
Page 16

17. Setting Up SSID on DVG-G5402SP
Step 1. Select “Setup” tab from the navigation panel and click on “Wireless Setup”.
Then, Click on “Wireless Basics” to configure basic wireless setting.
Page 17

18. Setting Up SSID on DVG-G5402SP
Step 2. Change the default “Wireless Network Name(SSID)” from “DVG-G5402SP to “SHxxxxxxx,” where xxxxxxx is the customer’s StarHub account number.
Step 3. Choose “Wireless Channel” to specified channel
(Auto Scan Mode is recommended in order to avoid channel interference
Step Mode can be set as b Only or g Only or Mixed Mode.
Step 5. Click “Apply” button to save the changes.
Page 18

19. Setting Up Wireless Security
Step 1. Select “Setup” tab from the navigation panel and click on “Wireless Setup-> Wireless Security” to configure wireless security setting 
Page 19

20. Setting Up Wireless Security
Step 2.  Select the encryption/authentication type: None, WEP, WPA, WPA2 and WPA2 Mixed.
Step 3.  Refer to the manual for detail configuration of each security mode
Page 20

21. Setting Up Wireless MAC filtering
Note: MAC filtering applies to the computers connected wirelessly. Make sure you had keyed in the correct MAC Address to prevent locking yourself out of the router
Step 1. Select “Advanced” tab from the navigation panel and click on
“Advanced Wireless”.
Then, Click on “Access Control” button to create MAC filter list
Page 21

22. Setting Up Wireless MAC filtering
Step 2. From the drop down menu of “Access Control Mode”, select the option “Allow”.
  When Allow Listed is enabled, only those wireless clients whose MAC addresses are in the Access Control List have rights to connect to the device
Step 3. In order to add the MAC address which you want to allow/deny access
DVG-G5402SP, Click on the “Add” button.
Page 22

23. Setting Up Wireless MAC filtering
Step 4 To know your PC’s Wireless adapters MAC address, click on Start  Run and enter CMD and Click on “OK”. On the DOS windows type “ipconfig /all”. You will see the MAC addresses of wireless adaptor. Key in the MAC address listed into the “MAC Address” field.
Page 23

24. Setting Up Wireless MAC filtering
Step 5. Enter the MAC address of the specified PC in the MAC field with xx:xx:xx:xx:xx:xx format.
Step 6. Click “Apply” to add the MAC address to the Wireless Access Control list.
Page 24

25. Setting Up Wireless MAC filtering
Step 7. The desired MAC address will now be in the “MAC Address” field as
shown in the example depicted below.
Step 8. In order to save and activate the new settings, Click “Save & Restart”
Otherwise, select “Maintenance” tab and click on “Backup and Restore” menu.
Page 25

26. Save and Reboot the DVG-G5402SP
Step 1. Click the “Save All Settings” check box and click on “Reboot” so that
the new settings will take effect after the VoIP Router is restarted.
Step 2. Press the “OK” button if “Reboot Device?” popup box come out.
Page 26

27. Troubleshooting Hardware problems:
Off hook and on hook a port, check if LED state changes
FXS port should give tones while off hooked
Check WAN and LAN LED to map your real connection
ping from PC, ping to PC, ping to Router, ping DNS Server
Software configuration problems:
Check “STATUS \ VoIP Status” page for SIP registration result, port state, and “STATUS \ Device Info” for WAN and LAN information. Always check if gateway has a correct WAN IP address allocated!
Page 27

28. Device Status – Device Info
Page 28

29. Device Status – VoIP Status
The status on this page reflect the VoIP telephone number and Registration Status of SIP Account.
Page 29

30. Device Status – RTP Statistics
Codec type, no of RTP packet sent and received, no of packet lost for each phone line can be seen on this page.
Page 30

31. Restore Default Setting
Method 1: Select “Restore Default Settings” under “MAINTENANCE-> Backup and Restore” to reset the VoIP Router’s settings back to the factory default settings via Web UI.
Method 2: Use Reset Button to restore factory default settings:
1. Power on.
2. Press and hold the reset button for 5 seconds.
3. Release the reset button. Factory settings will be restored.
Page 31