1. CADMIUM ZINC TELLURIDE (CZT) IMAGER INTRODUCTION : 1.SCIENTIFIC REQUIRMENT 2. DETECTORS USED IN IMAGER 3. ELECTRICAL CIRCUITS (FRONT END ELECTRONICSUSED) IN THE IMAGER 4. FUNCTIONING NEW CZT DETECTOR MODULE 5. DATA ACCUMULATION FROM VARIOUS DETECTOR TO ENCODER 6. GROUNDING SCHEME. 7. COMPONENT LIST USED IN THESE CIRCUITS.

2. 1)To achieve good spectroscopic capabilities in the range of 10 – 100 KeV with optimum background counts and spectral resolution, even in extended energy range up to 1MeV. 2)Since the detector construction and total area covered is such a way that With help of Coded Aperture Mass (CAM) a moderate image can be studied in 10 -100 KeV energy range. 3) CZT detector (pixilated form) has large energy bandwidth with fine resolution within 10 -100 KeV energy range. 4) Reducing background counts using collimation and anti-coincidence detector (Veto Detector) below the CZT detector plane.

3. SENSITIVITY OF CZT IMAGER Minimum detectable intensity = 3  N b / (A* T *  *  E) Photons /(cm 2 Sec Sr KeV) WHERE N b is background  is detector efficiency δE is the energy interval of observation T is the integration time BACKGROUND (N b ) HAS TO BE AS LOW AS POSSIBLE flux Energy Background Source

4. - 500 V DETECTOR MODULE CSPA XAIM3.2 CHIP QUADRANT 4 x 4 MODULE 16 X 16 CZT PIXEL ARRAY

5. FUNCTIONAL BLOCK DIAGRAM OF ANLOG CIRCUITS IN XaIm3.2 BIASES USED: 1) Threshold 2) Shaper time 3) Reset width 4) Delay Trigger with help of programming. A

6. 1. It is fully-driven charge signal acquisition chip. 3. Provision of programming for needed parameters of the chip like threshold, shaping time constant and various other parameter. ClkIn and RegIn are Clock and Input for the Shift- resistor. 2. All Analog and Digital outputs are current driven for 1 micro second. Each cell is addressable. 4. The chip requires +2 and -2 volts for operation. FEATURES OF ASIC XaIm3.2 5. Daisy chaining of chips.

8. M1M2M3Mn ADDR BUS DATA BUS TRIG & MULTI HIT DATA CLOCK ENERGY PULSE

9. SOXS payload on GSAT-II

10. CZT DET OPTO + PROCS ELCT R BF +V -V HV SCINTILATOR AMPL. P.D. + ADC HV 990V CSPA+ POST AMPLIFIER COMPARATOR BIAS FPGA

11. +5V 15V XAIM_OUTP XAIM_OUTM R53 9K09 R52 1K C22 47MF D2 1N4150 R51 1K R50 100E R49 162E Q2 2N2222 U13 HCPL4562 2 3 4 6 7 1 5 8 A K K2 C B NC E VCC R58 6K81 R57 14K7 R56 460E R55 750E Q5 2N2222 Q4 2N2222 R54 100E Q3 2N2222 R9 33E 1% DIFF. AMPLIFIER AMPL.WITH VARIABLE GAIN ANALOG SWITCH PEAK DETECTOR 12-BIT ADC FPGA SCHEMATIC BLOCK DIAGRAM OF CZT PROCESSING ELECTRONICS WINDOW COUNTERS To FPGA

13. AMPTEK 203 POST-AMPL. BIAS VOLTAGE LLD TO COUNTER M_CNTRL ANALOG SWITCH PEAK DETECTOR 8-BIT ADC VETO-PMT O/P

15. POST AMPL MONO COMPARATOR BIAS VOLTAGE CsI(Tl) S 3590 Si PIN PHOTO DIODE eV-5128 PRE-AMPL. Schematic block diagram of Alpha –Tag electronics.

16. 1 USF M-Rst AD 0 AD 15 CZT TRIG. LATCHOPTO 12-BIT ADC 8-BIT ADC 1. ANY EVENT MORE THAN LLD THRESHOLDE, TRIGERS THE CZT EVENT ANALYSIS. 2. NEXT CZT EVENT WILL ANALYSED ONLY AFTER 12-15 MICRO SEC 3- LINES OF COUNTERS MULTI-HIT ALPHA-TAG FPGA VCO 3-BIT GAIN CNTRL 3-BIT LLD CNTRL 3-BIT VETO LLD CNTRL VCO CNTRL CZT VETO MICRO-CONTROLER PROGRAMMING OF CZT MODULES

17. CZT WAVEFORMS VETO WAVEFORMS Veto_Trig. Pulse (1 U Sec.) Processing Time +ADC Con. Time (8 U Sec.) Read_Out _Time (4 U Sec.) Veto_Reset Pulse CZT Trig Pulse (1 U Sec.) Processing Time + ADC Conversion Time( 12 U Sec.) CZT Read _Out Pulse (2 U Sec.) Reset Pulse (1 U Sec.)

18. CZT TRIG. PULSE PROCESSING TIME +ADC CONV. TIME READ_OUT TIME RESET PROCESSING TIME + ADC CONV. TIME READ_OUT TIME VETO_RESET VETO TRIG. TIME

19. LV DC/DC used for powering all detectors and supporting electronics. Conventional High voltage supplies -500 volts for CZT biasing and +1000 volts for Veto PMT. Internal biasing voltages are generated inside the package.

20. HV Vf Vr POWER OSCI. + RECT.+ MULTI. SECTION SERIES PASS REGULATOR CURRENT SENSOR CKT. COMMANDS REFERENCE VOLTAGE CONTRL. DIFFERNTIAL AMPL. + V

22. MUX VOLTAGE CONTROL OSCILLATOR COMMANDS FROM FPGA + 5 V + 10 V LLD CZT LLD VETO THERMISTORE HV on-off HV Ref HV Feedback O/P Frequency 2 kHz TO 20 kHz For Variation of 0-10 volts