Presentation is loading. Please wait.

Presentation is loading. Please wait.

J. Valls, CMS L2-L3 Meeting, Sept 20021 ROD Production at CERN  ROD Flow During Production  ROD Flow at CERN  ROD Testing Areas  Infrastructure  Equipment.

Published byHarvey Harper Modified over 8 years ago

Similar presentations

Presentation on theme: "J. Valls, CMS L2-L3 Meeting, Sept 20021 ROD Production at CERN  ROD Flow During Production  ROD Flow at CERN  ROD Testing Areas  Infrastructure  Equipment."— Presentation transcript:

1 J. Valls, CMS L2-L3 Meeting, Sept 20021 ROD Production at CERN  ROD Flow During Production  ROD Flow at CERN  ROD Testing Areas  Infrastructure  Equipment Requirements Document  http://cern.ch/valls

2 J. Valls, CMS L2-L3 Meeting, Sept 2002 2 Goals To fully assemble, test and characterize a total of ~ 700 RODs …by the end 2004

3 J. Valls, CMS L2-L3 Meeting, Sept 2002 3 ROD Assembly Sequence  Mechanical ROD (ROD frames + pipes)  Electrical ROD (+ IC bus + IC boards + AOH)  Full ROD (+ Silicon)

4 J. Valls, CMS L2-L3 Meeting, Sept 2002 4 ROD Flow During Production ROD electrical integration ROD mechanical integration  IC bus and IC boards integration  Optoelectronics integration  CCUM, connectors, and cable assembly  Electrical tests with FE hybrids  Electrical RODs packaged and sent to FNAL and UCSB FNAL/UCSB ROD final qualification  Basic ROD operation Digital tests and readout errors Bad channel identification OH scans Total gain and offset scans Operational bias voltage  X-Y -source scans  Cosmic ray runs ROD silicon integration ROD qualification Helsinki Goal: Ready by March 2003 CERN

5 J. Valls, CMS L2-L3 Meeting, Sept 2002 5 ROD Flow at CERN CERN Spare Modules Storage Bin CERN Single Module Test Setup CERN -Source X-Y Scan Table CERN Single ROD Test Setup FNAL & USBC Modules and ROD CERN ROD Storage Bin CERN ROD Cosmic Rack ROD OK ROD Failure ROD OK Module OK

6 J. Valls, CMS L2-L3 Meeting, Sept 2002 6  -Source X-Y Scan Table Patch panel with connectors (HV, LV, controls, cooling) X-Y movement arms 3 RODS (any type) Rigid cover

7 J. Valls, CMS L2-L3 Meeting, Sept 2002 7 Delivery Schedule for Electrical RODs Testing Capability Rate (4 RODs/day) Wheel integration

8 J. Valls, CMS L2-L3 Meeting, Sept 2002 8 ROD Testing Areas  Building 598 ROD System Tests (prototypes SS, DS) Equipment Procurement and Quality Test Definitions for Production  Building 596 Electrical ROD Assembly and Tests  Building 186 ROD Production and Qualification Tests Tracker Assembly and Integration

9 J. Valls, CMS L2-L3 Meeting, Sept 2002 9 Building 186

10 J. Valls, CMS L2-L3 Meeting, Sept 2002 10 Building 186 (TOB Area) PS x-y Table Rod Hospital Cosmic Rack Cooling unit Cold room PS PS racks Rod storage PS racks Module Air cond 0.8 m 17.8 m 7.1 m Total Testing Area: 126 m 2 Tracker Assembly Hall Tracker Assembly Area 300 ROD capacity Goal: Ready by early 2003 Siemens 1 kW @ +5 0 C/32 0 C 5 kW @ +25 0 C (~400 W for 12 RODs)

11 J. Valls, CMS L2-L3 Meeting, Sept 2002 11 Infrastructure for 186  Gas Contact CERN gas working group  Grounding Contact TIS (?)  TIS Permissions  Conditioning Work Cleaning Furniture procurement Pipe work Etc. Goal: Ready by Dec 2002

12 J. Valls, CMS L2-L3 Meeting, Sept 2002 12 Equipment Needed for Production  DAQ Hardware 4 PC computers DAQ cards 1 ARC single module setup  High Voltage CAEN SY-127 Mainframe (10 boards A343, 2 kV, 200 A) CAEN SY-1527 Mainframe (6 boards A1511, 2 kV, 10 A-1 mA) Current Monitoring (CERN MSGC picoAmmeters) Controls (CAENET V288 VME)  Low Voltage DELPHI switching LV PS (redesigned) 3 LV control PS (testbench)  Cooling Units (and interlocks) Siemens Uniphase Cooling Unit (C 6 F 14 ), 1 kW @ +5 0 C / +32 0 C Refrigeration Unit at Build. 186 (C 6 F 14 ), 5 kW @ +25 0 C  DAQ Software XDAQ (beam-test program) XROD (system test)  Qualification and Acceptance Criteria Software  Integration into DB

13 J. Valls, CMS L2-L3 Meeting, Sept 2002 13 DAQ Test Setups at CERN  Single electrical ROD setup (Build. 596)  Single ROD setup (Build. 186)  X-Y table setup (3 RODS) (Build. 186) Max. APVs OEC Channels OEC Boards MUX Cards PMC-FED TSC/FEC Cards 48242311 / 1 Max. APVs OEC Channels OEC Boards MUX Cards PMC-FED TSC/FEC Cards 144726811 / 1 Max. APVs OEC Channels OEC Boards MUX Cards PMC-FED TSC/FEC Cards 48242311 / 1 120101433 / 3 Total: 121032 / 2 Available: (Build. 598)

14 J. Valls, CMS L2-L3 Meeting, Sept 2002 14 ROD Types  L1, L2  Double Sided RODs (DS) 12 modules, 4 APV  24 fibers  L3, L4  Single Sided RODs (SS4) 6 modules, 4 APV  12 fibers  L5, L6  Single Sided RODs (SS6) 6 modules, 6 APV  18 fibers

Download ppt "J. Valls, CMS L2-L3 Meeting, Sept 20021 ROD Production at CERN  ROD Flow During Production  ROD Flow at CERN  ROD Testing Areas  Infrastructure  Equipment."

Similar presentations

Slide 1UCSB CMS Weekly Status MeetingCMS 4-Hybrid Test System Sam Burke EE 4-Hybrid Thermal Test System Status 27 May Sam Burke UCSB HEP Group.

Slide 1UCSB CMS Weekly Status MeetingCMS 4-Hybrid Test System Sam Burke EE 4-Hybrid Thermal Test System Status 27 May Sam Burke UCSB HEP Group.
1/8/04Lance Simms Thermal Testing of TOB/TEC Hybrids at UCSB.

1/8/04Lance Simms Thermal Testing of TOB/TEC Hybrids at UCSB.
Slide 1L3 Testing Meeting March 7, 2003UCSB Status-Anthony Affolder UCSB Testing Status Anthony Affolder (for the UCSB module testing group) Current testing.

Slide 1L3 Testing Meeting March 7, 2003UCSB Status-Anthony Affolder UCSB Testing Status Anthony Affolder (for the UCSB module testing group) Current testing.
1 Long Term Module Testing-Anthony AffolderTPO, December 11, 2003 Current Module LT Testing Capability Only Vienna Boxes Available  10 slots at each site.

1 Long Term Module Testing-Anthony AffolderTPO, December 11, 2003 Current Module LT Testing Capability Only Vienna Boxes Available  10 slots at each site.
Juan Valls 1 TOB System Test Status Report  DS ROD System Test Setup  DAQ Software  DS ROD Characterization PLL, FED Timing Scans OPTO Scans  Noise.

Juan Valls 1 TOB System Test Status Report  DS ROD System Test Setup  DAQ Software  DS ROD Characterization PLL, FED Timing Scans OPTO Scans  Noise.
4/25/2006 Puneeth Kalavase, UC, Santa Barbara On behalf of US Tracker Outer Barrel group Construction and Testing of CMS “Rods”

4/25/2006 Puneeth Kalavase, UC, Santa Barbara On behalf of US Tracker Outer Barrel group Construction and Testing of CMS “Rods”
Slide 1UCSB CMS Weekly Status MeetingCMS 4-Hybrid Test System Sam Burke EE UCSB 4-Hybrid Thermal Test System Status 13 October 2003 Sam Burke Lance Simms.

Slide 1UCSB CMS Weekly Status MeetingCMS 4-Hybrid Test System Sam Burke EE UCSB 4-Hybrid Thermal Test System Status 13 October 2003 Sam Burke Lance Simms.
US Module and Rod Production Overview and Plan For the US CMS Tracker Group.

US Module and Rod Production Overview and Plan For the US CMS Tracker Group.
CMS Tracker Week – Module Test Meeting – July 2003 – Patrick Gartung 1 Long term rod testing software Patrick Gartung University of California, Riverside.

CMS Tracker Week – Module Test Meeting – July 2003 – Patrick Gartung 1 Long term rod testing software Patrick Gartung University of California, Riverside.
Slide 1 Anthony Affolder US Silicon Meeting, March 9, 2004 Equipment Status ARCS equipment status à Single module and 4 hybrid DAQ equipment status à Vienna.

Slide 1 Anthony Affolder US Silicon Meeting, March 9, 2004 Equipment Status ARCS equipment status à Single module and 4 hybrid DAQ equipment status à Vienna.
Slide 1Rod Production presented by Jim Lamb (UCSB)April 9, 2004 Rod Production Rod Production, April 9 2004, presented by Jim Lamb (UCSB)

Slide 1Rod Production presented by Jim Lamb (UCSB)April 9, 2004 Rod Production Rod Production, April , presented by Jim Lamb (UCSB)
US CMS Silicon Electronics Testing – CMS Lehman Review - May 21, 2003 - Affolder1 US CMS Silicon Electronics Testing US CMS Lehman Review BNL 5/21/03 A.

US CMS Silicon Electronics Testing – CMS Lehman Review - May 21, Affolder1 US CMS Silicon Electronics Testing US CMS Lehman Review BNL 5/21/03 A.
Andrea Giammanco CMS Tracker Week April 20031 DS ROD Prototype: “final” optohybrids “final” CCUM integrated in the rod with new FEC_to_CCUM adapter (Guido.

Andrea Giammanco CMS Tracker Week April DS ROD Prototype: “final” optohybrids “final” CCUM integrated in the rod with new FEC_to_CCUM adapter (Guido.
28 June 2005C. Campagnari (UCSB)1 Status of Rod Production at UCSB This report covers the last week Reporting for: Dan Callahan Susanne Kyre Stephen Jaditz.

28 June 2005C. Campagnari (UCSB)1 Status of Rod Production at UCSB This report covers the last week Reporting for: Dan Callahan Susanne Kyre Stephen Jaditz.
CMS Tracker Week – Module Test Meeting – April 2003 – Patrick Gartung 1 Status of US long term module testing Patrick Gartung University of California,

CMS Tracker Week – Module Test Meeting – April 2003 – Patrick Gartung 1 Status of US long term module testing Patrick Gartung University of California,
Anthony AffolderUS CMS Meeting 12/3/02DAQ Based Systems LV/HV Needs DAQ Power Supply Needs HV à 600 V/~1mA range –0.1-1  A Current Sensing –Over Voltage/Current.

Anthony AffolderUS CMS Meeting 12/3/02DAQ Based Systems LV/HV Needs DAQ Power Supply Needs HV à 600 V/~1mA range –0.1-1  A Current Sensing –Over Voltage/Current.
Nilanga Liyanage University of Virginia UVa GEM Team Dr. Kondo Gnanvo, Dr. Vladimir Nelyubin, Kiadtisak Saenboonruang, Chao Gu, Xinzhan Bai, Jie Liu, Seth.

Nilanga Liyanage University of Virginia UVa GEM Team Dr. Kondo Gnanvo, Dr. Vladimir Nelyubin, Kiadtisak Saenboonruang, Chao Gu, Xinzhan Bai, Jie Liu, Seth.
Low Voltage Power Requirement of TOF FEEs. Maximum 110 4.8 tray. Low Noise:  Periodic and Random Distortion (PARD) < few mV RMS Floating.

Low Voltage Power Requirement of TOF FEEs. Maximum tray. Low Noise:  Periodic and Random Distortion (PARD) < few mV RMS Floating.
18-Jan-021W. Karpinski System Test 2002 1.Design verification of petals and interconnect boards and control links without detectors a)mechanics b)electrical.

18-Jan-021W. Karpinski System Test Design verification of petals and interconnect boards and control links without detectors a)mechanics b)electrical.
Saverio Minutoli INFN Genova 1 1 T1 Electronic status Electronics Cards involved: Anode Front End Card Cathode Front End Card Read-Out Control card VFAT.

Saverio Minutoli INFN Genova 1 1 T1 Electronic status Electronics Cards involved: Anode Front End Card Cathode Front End Card Read-Out Control card VFAT.

Similar presentations

Ads by Google