BASICS OF UK DETAILING. BS Codes : 1) Design code: BS8110 2) Detailing codes: BS8666 BS4449.

Slides:

Advertisements

Similar presentations

Elongation Requirements for Stainless Steel Rebar

Advertisements

2.2 STRUCTURAL ELEMENT BEAM

2.2 STRUCTURAL ELEMENT Reinforced Concrete Slabs

Chp12- Footings.

Summary Sheet Session Number : Date : Subject Expert : Dr. M.C. Nataraja Professor Department of Civil Engineering, S.J. College of Engineering,

Prof Awad S. Hanna Concrete Structures Concrete Structures.

Reinforced Concrete Design-8

Commercial Framing C D Prints Unit 13.

EDT Foundation Plan Design1 Weekend Cabin Retreat Project Foundations Sacramento City College EDT 300.

1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore Mob:

Lecture Goals Slab design reinforcement.

ONE-WAY SLAB. ONE-WAY SLAB Introduction A slab is structural element whose thickness is small compared to its own length and width. Slabs are usually.

Design and drawing of RC Structures CV61

Department of Civil Engineering NED University Engineering & Technology Building Prof Sarosh Lodi.

PowerPoint Presentation

CARES and the reinforced concrete industry

Introduction to a pit-less electronic scale “concrete deck” The scale to be shown is a B-Tek Side/Rail full electronic Platform is 70’x11’ on a slab design.

1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore Mob:

Code Comparison between

COLUMNS. COLUMNS Introduction According to ACI Code 2.1, a structural element with a ratio of height-to least lateral dimension exceeding three used.

Introduction to Columns

Reinforced Concrete Design-II

Metals. Introduction u Metal is used in various places in the construction process including: –rebar = reinforcing steel in round shapes –flashing = thin.

Composite Beams and Columns

Introduction to a pit installation

Section 1 Dr.Hoda’s part Sheet 1: Calculating equipment cost Eng. Reda Zein.

Plain & Reinforced Concrete-1 CE-313

Reading Structural Drawings

1 HVACR116 – Trade Skills Structural Drawings. 2.

Seventh Edition By David A. Madsen, Terence M. Shumaker, and David P. Madsen Civil Drafting Technology Chapter 13 Civil Engineering Detail Drawings.

PAVSYS PAVSYS ™ PAVSYS PAVSYS MODULAR ENGINEERED SUSTAINABLE HABITATS.

1 Design and drawing of RC Structures CV61 Dr. G.S.Suresh Civil Engineering Department The National Institute of Engineering Mysore Mob:

1 Mechanical for Oil Heat Mechanical codes. 2 Every state has codes. They may be the same in some states, but different in other states. Always have a.

CE A433 – RC Design T. Bart Quimby, P.E., Ph.D. Revised Spring 2009

Isolated footing with axial load and moment

4.7 Triangle Inequalities. Theorem 4.10 If one side of a triangle is longer than another side, then the angle opposite the longer side is larger than.

Composite Construction

Chapter 21 Building Sections. Chapter 21 Building Sections.

Orthographic Drawings

© Goodheart-Willcox Co., Inc. Permission granted to reproduce for educational use only 1 Learning Objectives Identify the primary features included in.

Reinforcement Information - Code

Practical Design of PT Buildings

Chapter 40 Fireplace Construction and Layout. Introduction As sections are drawn, consideration must be given to the fireplace and chimney –Metal fireplaces.

Prof. Shrikant M. Harle Asst prof. Dept of Civil Engg PRMCEAM

Dr Badorul Hisham Abu Bakar

1 of 15Sheet Concrete 4ksi, Re-bar Grade 60Material RC Pier – Elevation View 1TITLE UNIT: in. NEESR Pier Top Bottom View.

An-Najah National University Faculty of Engineering

Introduction Used for covering spaces in the form of roof or floor

Structural Design of Technology College in Hebron University

Drawing generation plugin

(i) proper arrangement of reinforcing bars and

An-Najah National University

Cutting diameter tolerances: 1/32" through 31/64": ", -

Structure II Course Code: ARCH 209 Dr. Aeid A. Abdulrazeg

Stainless Steel Water Well Casing.

Concrete Structures DR. Nabil Dmaidi.

Columns With Combined Bending and Axial Load

Tubes Dimensions Tube diameters in the range 5/8 in. (16 mm) to 2 in. (50 mm) are used. The smaller diameters 5/8 to 1 in. (16 to 25 mm) are preferred.

By :Dr. Aeid A. Abdulrazeg

Concrete A structural material made by combining cement, sand, aggregate, and water.

A Step-by-Step Procedure for Preparing Optimized Bar Cutting Arrangements Using OptiBarCut Select BarBeQue 2009 Icon From Desktop Start Program OptiBarCut.

Dr S.Sreenath PhD, MSc Engg, MSc (ICM), MBA

Types of Metal.

- '1:- bs? a ' I.

Structure II Course Code: ARCH 209 Dr. Aeid A. Abdulrazeg.

Reinforced concrete column

Presentation transcript:

BASICS OF UK DETAILING

BS Codes : 1) Design code: BS8110 2) Detailing codes: BS8666 BS4449

SHEET SIZE- A1 (594X841) size sheet generally used. SCALES- general arrangement- 1:100 wall & slab detail-1:50 beam & column elevations-1:50 sections-1:25 ( larger scales specified in BS :20,1:10,1:5,1:2)

REINFORCEMENT: Grade: generally grade 500 rebar has been used (grade446&250 omitted in BS4449:2005) Rebar Diameters: 8,10,16,20,25,32 & 40mm generally use

Notations: As per BS TYPENOTATION Grade B500A,B500B or B500C H Grade B500A A Grade B500B or B500C B Grade B500C C Stainless steel S

Stock length: 12m stock length for 12mm and above for smaller size 8, 9 or 10m Bent bar: shortest side should not exceed 2.75m