Freehand Sketching. Draw a horizontal line about 70 mm long, and then another six lines underneath, each separated by about 10 mm.

Slides:



Advertisements
Similar presentations
Angles and Properties.
Advertisements

Shawlands Academy Department Of Technical Education
Cylinders.  Cylinders are shapes that have a circular cross section and a depth.  They are used in shapes of bottles and their developments are used.
Technological Systems Unit 1 ~ How They Work Lesson 1 ~ Exploring Technological Systems Technical Sketching.
Begin with the horizon line in the middle (please excuse my very crooked lines!!! pencil did not photograph well, so I had to redraw some lines with my.
3 rd Angle Projection A 3 rd Angle projection is a 2D drawing of a 3D object. It shows three views the side, plan and end view. The side view is drawn.
Lines Identifying Different Types of Lines. LINES There are many different types of lines. Can you think of any? vertical horizontal diagonal perpendicular.
Parallel Lines and Parallelograms Draw and explain parallel lines. Draw and define parallelograms.
Shapes Preschool. Circles and Ovals Let’s trace the shapes and see which object they match!
Plane Shapes Plane Shapes Two-Dimensional Shapes.
Choose or draw a suitable A3 border sheet and start drawing. (do not draw the dimensions these are for guidance only)
Orthographic Projection: an introduction
Pyramid Construction Pyramids Square Rectangle Hex Cone.
3rd Angle Orthographic Projection
ISOMETRIC CIRCLE.
1.What are they? 2.Why do we need to draw them? 3.How do you draw them? 4.Exercises.
Dimensioning Dimensioning Gateway To Technology®
Graphic Communication
5.4 Hyperbolas 1 Please note the minus in the middle. A “+” in the middle makes the graph an ellipse. A minus in the middle will give us a hyperbola which.
What is this type of drawing called? Perspective Drawing.
Greenfaulds High School Orthographic Views. Orthographic Projection Orthographic projection is the name given to the type of drawing where a 3D object.
Projection of Planes Plane figures or surfaces have only two dimensions, viz. length & breadth. They do not have thickness. A plane figure, extended if.
Freehand Two Point Perspective Drawing Abilities Teacher © J Lewis 2004.
Step One Draw a square on your paper. Step Two Beginning in the top left corner of the square, measure to the right about a half inch and place a dot.
This is the finished body RADIUS LOFT EXTRUDE. Creating the body taper Open the wing Click on new part in context.
Lines Identifying Different Types of Lines Next Type your name and send: Next.
Perspective Drawing Uses line to show depth, form, and deep space Uses vanishing points on a horizon line in city and landscapes Vertical lines, horizontal.
Making a Lego block in SolidWorks
Assignment D6.  CURVES include lines and arcs  A PROFILE is a closed region made up of curves  When you have trouble with a sketch that you can’t extrude,
INTRODUCING WHAT ARE THEY ? SEE SOME EXAMPLES HOW DO YOU DO IT ? EXERCISES.
3 rd Angle Projection A 3 rd Angle projection is a 2D drawing of a 3D object. It shows three views the side view is drawn first. The plan view is drawn.
Design and technology st aidan’s high A pictorial sketch of a wall lamp is shown. The shade is in the form of a cut cone. Draw, from the given.
Menu Cones Cones – What Are They?. Menu Cones Drawing an Orthographic Cone You will be given sheets that will have the following views of a cone. These.
Perspective Drawings Linear perspective is a geometric method of representing the apparent diminishing of scale as the distance from object to viewer increases.
The Tail, this is what we want to make. Extrude Mirror Radius.
A/F Hexagon Construction
Cones.  Cones are shapes that have a circular base and come to one point at the top.
90 Vertical Horizontal Oblique line a b Angles a + b = 180 o Angles at a Point b = 115 o Angle a = 180 – 115 = 65 o.
1 Point Perspective Students will tape down a piece of paper and go through the steps As we go through the presentation.
One Point Perspective: City Drawing A Tutorial
Cones. Cones are shapes that have a circular base and come to one point at the top.
Third angle orthographic projection
Thurso High School Design and Technology Tutorial Two Dice.
1.To begin click: File, New, then select Design 2.Next draw a rectangle. 3. Use the measuring tool to dimension the sides to 150mm by 75mm 4. Change to.
Prime & Composite Numbers Prime & Composite Numbers © Math As A Second Language All Rights Reserved 4.OA#4.
Draw the plan and the elevation of the cylinder, leaving 30mm between views Ø 40.
Types of triangle 1. right angle 2. isoceles 3. equilateral 4. scalene
MULTIPLICATION 5 Multiplicand X 3 Multiplier 15 Product LET’S LEARN
Making Finger Joints.
Deans Community High School
Drawing Alcoves using One Point Perspective
Using One Point Perspective to Combine Shapes
Regular Geometry Shapes
Graphic Communication
A/C Hexagon Construction
How to equally divide a circle
Freehand Two Point Perspective
Grand Prix Racing Circuit
Use a ruler or tape measure to help you find the center of the circle
Space and Shape.
TEE SQUARE, SET SQUARES, COMPASS AND PROTRACTOR
Drawing Walls for a Room
Using One Point Perspective to Combine Shapes
Graphic Communication
This diagram helps explains why angles at a point add to 360o.
Cross Sections.
2 POINT PERSPECTIVE.
Identifying Different Types of Lines
“The Walk Through Factorer”
Op Art Directions.
Presentation transcript:

Freehand Sketching

Draw a horizontal line about 70 mm long, and then another six lines underneath, each separated by about 10 mm.

Draw a vertical line about 70 mm long, and then another six lines beside it, separated by about 10 mm.

Draw a faint dotted line in a 70 mm square, and then draw diagonal lines inside the square, separated by 10 mm.

Draw one horizontal and one vertical line in a cross shape. Check the angle in the middle to see if it’s square once you've finished.

Draw the cross again, and then add two diagonal lines. Check the two right angles in the middle are square.

Draw a square, with each side about 70 mm long. Check the corners are square when you've finished.

Draw another square, as above, and then draw a diamond on top. Check all corners are square when you've finished.

Draw a cross 100 mm x 100 mm. Mark 50 mm from the centre in all four directions. Then draw four separate arcs, so that they meet up as a circle.

Draw one horizontal and one vertical line, each 70 mm long, meeting at one end. Then draw five concentric arcs, separated by 10 mm.

Draw a faint dotted line 50 mm x 50 mm square. Then draw a series of continuous loops inside the box.