- + NC NO C 6 1 2-3 4 5 sw3 sw4 motor Cross-switch Microswitch Battery.

Slides:

Advertisements

Similar presentations

Problem Based Learning How to open a combination lock.

Advertisements

QUIZ-A QUICK PROGRESS CHECK ON YOUR UNDERSTANDING.

Full Speed Ahead Introductory Presentation. Opening Activity Choose one of the objects to the right and in ten or more steps explain how it goes from.

TLA. Replacing The Battery On the Back of the pager press in this button while moving the door away from the pager, then lift up. On the Back of the pager.

Solar turbine. If the sun's rays fall on the photovoltaic cell, which is connected to the side of the windmill, it is converted into electricity able.

Step-by-Step Procedures PREVIOUS NEXT Print Entire Procedure Grilling Step 1: Brush a small amount of oil on the items to be grilled and season as desired.

How to properly clean your paint brush and paint trays This is a sink. This is the place where you wash your brushes and other painting supplies.

Starting System Fundamentals.

Overview. Action ! Once more! 1-2 Stand up! 林順松

©2006 CSUC Institute for Research in Intelligent Systems Electric Generator June 13, 2006.

Astro Tech LC-6 Digital Chronometer

Chapter 22 Electromagnetic Induction. 1) Induced emf and induced current Changing B-field induces current.

Rd 3 - Electronics 1.Ohm’s Law 2.Potential Divider 3.Resistor in Series and Parallel - Application of Ohm’s Law 4. Switches and Relay.

Robotics- Basic On/Off Control Considerations. On/Off Control Forms the basis of most robotics operations Is deceptively simple until the consequences.

Unit: Energy and Control- Electricity.  English Scientist William Sturgeon invented the first electromagnet in He wrapped a coil of wire around.

Scribbler Movements Sec 9-3 Web Design. Objectives The student will: Understand the basic movement commands for the Scribbler Know how to create and execute.

Continue The information provided in this training module covers the schematic flow charts for all ovens and ranges that utilized a preheat board, Self.

Getting Started! Lego Mindstorms Program NXT 2.0.

Wait Program! WAIT please!. 1. Why is it often better to use conditional commands rather than program a robot to move exact distances? 2. What is the.

LabVIEW Basics Review LabVIEW Robotics Fundamentals.

How to link the robot and the computer (Bluetooth) How to turn on and off How to connect the adaptor Fluke card connection Sec Getting Started How.

Technical Writing for Robotic Coding!.  du/products/teaching_robotc_cort ex/fundamentals/introtoprogramm ing/thinking/videos/fundamentals.

What Makes an Electric Motor Work? The Science and Technology Behind Electric Motors.

Castor Bot. Now, we will begin creating a robot Log onto your computer On your screen, click on the website labeled “castor bot” Your building instructions.

What do I have to do? Cause a motor to turn the center arm. attach motor to frame can redesign the center arm piece as needed use bushings or bearings.

LEGO® MINDSTORMS® NXT Move Block.

PARALLEL PLATES. From previous work, the electric field strength can be found from the electric force on a test charge.

Find the Standard Deviation of 6,5,5,4,5,5,6,5 and 4 Finding Standard Deviation We first need to make sure the calculator is CL ea R of all previous content.

Gabi Maisonet. How it Works: Regenerative Braking: Electric motor cause resistance causing the wheels to slow down. As a result the energy from the.

Automated Mechanisms Help. Potentiometers Potentiometer Check –Analog Port 2 How they work –Analog sensor –Measures rotation of a shaft between 0 and.

Programming 101 The Common Palette Content provided by Connor Statham (9 th Grade Student) Formatting by Shannon Sieber.

How to use the Hand-In Folder. Click on the Folder icon at the bottom of the screen.

Tutorials NXT-G / EV3 Programming. Tutorials NXT-GEV3.

Quadcopter Setup. 1. Fully charge batteries on Quadcopter, Remote Control and WiFi extender.

Click the pictures to advance to next slide Use the left arrow to go back.

Designing a Next-Generation Surgical Robot Activity.

4) Design the logic to control the motor on a simple remote control car. There are two buttons on the remote control for the motor. If neither button is.

3:00. 2:59 2:58 2:57 2:56 2:55 2:54 2:53 2:52.

Step 1 Spin the dial at least two times to the right (clockwise), all the way around. This "clears" the lock of any previous numbers. Turn the dial to.

Obstacle Detection. In the previous program the robot moves forward and then checks for something in the way. As we observed it only checks for things.

Maglev Velocity Challenge. Challenge: Build a motorized maglev car that will travel down the track with the greastest velocity.

Armdroid 1000 Programming the Armdroid G-2000 Mode G-3000 Mode Next.

Portable Electric Drills By: Mason Young. 1. Properly secure drill bits in the chuck of the portable drills.

Light Pods Dec Pod Motor Diode Lotus Plus 2 Electric Motor Light Pod Wiring Dec 2009 with Stu’s specific loom modifications Rotary Switch Rotary.

Solar Energy Car.

JC Technology Components.

The principal of the electric motor

If you have difficulty, immediately notify an instructor.

Introductory Presentation

Top Fire Protection Services Ottawa available on Dubinskyconstruction

Canon Customer Support First you need to turn on your Printer. Press & hold the “Reset button” on the printer. While pressing the “Reset.

Learning Outcomes Understand While Loop

Introductory Presentation

DRV3201 Waveforms 7/2/2015.

Carbot Robot By Ruben Cossyleon

Game Controller Lesson Three.

Creating an Arm.

BEGINNER PROGRAMMING LESSON

Mean Absolute Deviation

BEGINNER PROGRAMMING LESSON

How to Use Your Lock.

Lesson 3: Sensor Wait-for’s Programming Solutions

Game Controller Lesson Two.

Playing Freeze Tag.

Using a Drawing Robot to Make Angles (Using Rotations)

DO NOT OPEN YOUR BINDER UNTIL INSTRUCTED

Source: Motor Source:

Programmable Logic Controllers (PLCs)

VEX Drag Race Your name, date, hour.

Presentation transcript:

- + NC NO C sw3 sw4 motor Cross-switch Microswitch Battery

Turning the cross-switch The motor starts rotating in one direction

- + NC NO C sw3 sw4 motor Battery Microswitch Cross-switch

- + NC NO C sw3 sw4 motor Cross-switch Microswitch Battery Microswitch

- + NC NO C sw3 sw4 motor Cross-switch Microswitch Battery The motor stops

Turning again the cross-switch The motor starts rotating in the contrary direction

- + NC NO C sw3 sw4 motor Cross-switch Microswitch Battery

- + NC NO C sw3 sw4 motor Cross-switch Microswitch Battery

- + NC NO C sw3 sw4 motor The motor stops again Cross-switch Microswitch Battery

Until when? Until pressing the corresponding microswitch

The motor stops because the microswitch is activated Turning the cross-switch : The motor starts rotating in the contrary direction and The previous activated microswitch, returns to its previous position.