dsdfsa Zoomed in view… Fasteners Assignment Part C: 3/8-16 UNC-2A 1.5 FLAT HEAD.

Slides:

Advertisements

Similar presentations

Drafting Technology Threaded Fasteners.

Advertisements

Assembly Instructions DucoSlide Luxframe Controllable TOP BOTTOM L.H. R.H. Control side FRONT SIDE in open position REAR SIDE in open position 1.

FASTENERS Screws, Nails, Bolts…. SCREWS AND NAILS Must resist corrosion Rusting fasteners retain moisture Rot Bleed.

Types of Screw.

1 GRADING AND DAYLIGHTING  The Daylighting commands calculate slope daylighting from a polyline footprint to a surface.  A 2D or 3D polyline with elevational.

Page 1 1. Circles (2), center point 2.5, radius &.875 radius Line, start 2.5, ” length 2. Circles (2), center point (right end of line).5625.

Major Diameter: The largest diameter of the thread Minor Diameter: The smallest diameter of the thread Pitch: Distance between two threads (mm) or no of.

Copyright © Texas Education Agency, All rights reserved.

Fasteners Assignment Part C: 3/8-16 UNC-2A 1.5 FLAT HEAD.

Manufacturing Assembly Plan P Mechanical Spine Test Platform.

Threads and Fasteners.

© Dr Simin Nasseri Southern Polytechnic State University 1 Copyright © The McGraw-Hill Companies, Inc. Permission required for reproduction or display.

EML 2023 – Threads and Fasteners

Drill Press Operations

Multi-View Drawing (Text Chapter 8)

Common Tools in Woodworking

Lesson No. 11 Week No. 07 Name of lesson Marking Tools

J-FRM-0101 Revision with Reason No.DateInitials Drawing No. D’Vinyl Inc. Descriptive Part Name Designed byChecked by Engineer Drawing Type Foot Plate Date.

ISOMETRICS Isometric means “equal in measure” and refers to the fact that the three receding axes are tilted at 30°. Isometric drawings are constructed.

Threads, Fasteners, and Springs Chapter Technical Drawing 13 th Edition Giesecke, Mitchell, Spencer, Hill Dygdon, Novak, Lockhart © 2009 Pearson.

Tutorial (Basics in SolidWorks) 小明 in ERB106.  Modeling  2D ▪ Sketching ▪ Dimensioning ▪ Mirror/Pattern ▪ Trim/Extend ▪ Fillet/Chamfer  3D ▪ Extruded/

Engineering Graphics A few highlights

Types of Threaded Fasteners.  Used to hold parts together  Clearance holes in parts  Nut on other end  Can also be used with a threaded hole.

Dimensioning Dimensioning Gateway To Technology®

Metal Joining Metal joints can be temporary or permanent.

Plain Mirror Style SNC2D. Angles – What’s It All Mean?

Types of Screw. Mirror screw This is a flat-head wood screw with a tapped hole in the head, which receives a screw-in chrome-plated cover. It is usually.

Final Assignment Air Car Chassis Design using Sketchup.

ADVANCED MECHANICAL DRAFTING

Step one: Page Border and title block. Border will be ¼” from the edge of the paper. Drawing will be done in landscape format. Title block will be 1”

Lesson 7 Rectangular Objects. Rectangle Command Rectangles with Vertices on the Origin Start from the origin End at the origin.

2012 IDEA ASSEMBLY “HINT” PACK. ARM: draw in 2D Copy / paste this view into Inventor.

14.52 in Attach the Axle to the chassis using the four (4) bolts, washers, and nylon lock nuts. Mount the tires. Note: The wheel recess outside on the.

Hole Types & How To 4 main types of holes: Clearance Hole Tapped/Threaded Hole Countersunk Hole Counterbored Hole.

Design Review RSXS - EndStation Review on Vacuum Chamber Stand and Supports Location Beamline Roll-up Endstation.

1 Manufacturing Projects Flexible Manufacturing Copyright © Texas Education Agency, All rights reserved.

Side view of generator. Close up of unused grounding pad - gives provisions for mounting the absorber.

Sectionals Sliced view of a part or component in a drawing showing its internal make up.componentdrawing.

Assignment D6.  CURVES include lines and arcs  A PROFILE is a closed region made up of curves  When you have trouble with a sketch that you can’t extrude,

Learning Objectives • Create sweep features. • Create lofted features.

IOT POLY ENGINEERING Trade homework assignments with a partner. 2.Measure each of your partner’s answers. 3.Place a check next to correct measurements.

Cones.  Cones are shapes that have a circular base and come to one point at the top.

Train Body The next series of slides will guide you through the construction of the train body. Start a new drawing and save it as Train Body.

Definitions and callouts

Cones. Cones are shapes that have a circular base and come to one point at the top.

Sensor Module v1.1. Step 1: Sand edges of PCB & drill bolt holes (3mm) Use small green power drill or pillar drill (as available) Goggles Use a piece.

Description of Hand Tools Tools help us do work and make things. Tools.

ADVANCED MECHANICAL DRAFTING

Drawing of bolt and nut.

CHAPTER 12 THREADS, FASTENERS AND SPRING

VIEW SERIES with Sliding Door

Flexible Manufacturing

Today’s Plan Fasteners Threading Fasteners.

Threads and Fasteners.

Assembly Drawings.

Fasteners Con’t.

Introduction to SolidWorks

Alternate Views Introduction to Engineering Design

Year 11 Occupational Studies – Carpentry and Joinery

Fastening devices.

EML 2023 – Threads and Fasteners

Drawing of stud.

FASTENERS Screws, Nails, Bolts….

McMaster linear bearing #6709K180 with guide rail suppressed

Break down Lance rack Cut one of each of these for each rack

DucoSlide Luxframe F Fitting instructions L.H. R.H.

EML 2023 – Threads and Fasteners

Miniature Train Wheels.

Presentation transcript:

dsdfsa

Zoomed in view…

Fasteners Assignment Part C: 3/8-16 UNC-2A 1.5 FLAT HEAD

Check PDF packet page one for quick reference to page numbers… Start by drawing the following vertical rectangle.375x1.5

Offset top line down ½ D (0.1875) Draw a line from the blue circle intersection heading Mirror angled line over to the left side of the fastener and fillet, trim, extend, / erase.

Add slot for screw driver. Dimensions for height and width are 1/4D as noted in the book example.

Check last page of PDF for dimensions of steel plates. Top plate has a clearance hole for the fastener. Bottom plate is tapped (threaded)- See page 1 of PDF for page number referencing threaded holes Bottom plate has more threads cut than length of bolt, i.e. bolt can’t bottom out without fully tightening down. Pilot hole (pre-drilled hole before tapping can occur) extends lower than threads and has 80 degree angle (same as the twist drill bit that cut the hole). Dimensions can be “eye balled.”