How To Make A Simple Circuit Speaker By: Brian Thomas, Dan Sampson, Brendan Dempsey, Ryan Boarder, Mikael Adane.

Slides:

Advertisements

Similar presentations

UVM CricketSat Assembly Manual. Getting Started Make a hard copy print out of the following page It will help you identify the proper components Place.

Advertisements

Jiggy Bot Aka Cyclops.

AP Electricity Quiz Review

CricketSat Receiver Assembly Instructions This is the instruction slides for the assembly of a receiver board. It would be a good idea to review soldering.

CricketSat Assembly.

- wire + wire D size battery Magnet wire coil magnets Paper clips Support board.

MOOD LIGHT PCB ASSEMBLY V By Phil Townshend 2008.

CricketSat LP (Transmitter) Assembly Instructions This is the instruction slides for the assembly of a transmitter board. This is the board that will fly.

Lesson Objectives To learn how to solder components onto a circuit board safely and correctly. Success Criteria Must Be able to understand the health and.

Electronics Merit Badge Class 4 5/17/2015Electronics Merit Badge Class National Scout Jamboree1.

1 Hands-on: Heater Circuit Kit includes: 3 9 Volt batteries (for flight only) 1 Perf Board 3Ceramic Resistors (4 5W) 39 V connectors 1 White wire 1.

Assembly Manual Mike Fortney 04/02/2006 CricketSat LC Receiver.

CricketSat Receiver Assembly Manual Mike Fortney 06/26/2006.

Colorado Space Grant Consortium Timing Circuit HW #4 Class #07 Timing Circuit HW #4 Class #07.

Learn-to-Solder Exercise: Practice Flasher Circuit AEM 1905: Spaceflight with Ballooning University of Minnesota.

1 Student Hands On Training I (2007) Timing Circuit & Camera Integration Timing Circuit & Camera Integration.

You will need the following parts from your kit: 1.Breadboard ohm resistor (brown, black, brown, gold) 3.1 LED (light emitting diode) 4.1 Potentiometer.

Electronic Component Functions What is this component doing my in electronic device?

SPH3U Simple Circuit Start with a simple electric circuit, with a 6.0 V battery source and a single 10  resistor V T = 6.0 V IT=IT= R T = 10  Resistor.

Fire Alarm Manish Choudhary. 2nd - 3rd Nov. 2010Science Bus - Technology2 Course Plan  Highlight Importance of Fire Safety  Instructions to Set Up Fire.

NPN Foundations of Technology NPN © 2013 International Technology and Engineering Educators Association, STEM  Center for Teaching and Learning™ Foundations.

Speaker Foundations of Technology Speaker © 2013 International Technology and Engineering Educators Association, STEM  Center for Teaching and Learning™

Printed Circuit Board (PCB) manufacture Learning outcomes: To work effectively, independently and in small groups. To understand the importance of personal.

Oscillator Foundations of Technology Oscillator © 2013 International Technology and Engineering Educators Association, STEM  Center for Teaching and Learning™

SCR (Silicon-Controlled Rectifier) Foundations of Technology SCR (Silicon-Controlled Rectifier) © 2013 International Technology and Engineering Educators.

RC Circuits. We can use a resistor to slow the charging of the capacitor. -Current now varies with time. -In the very short term, you can treat the capacitor.

Series and Parallel Circuits ~different ways of wiring multiple resistors.

Potentiometer Foundations of Technology Potentiometer © 2013 International Technology and Engineering Educators Association, STEM  Center for Teaching.

Capacitor Foundations of Technology Capacitor © 2013 International Technology and Engineering Educators Association, STEM  Center for Teaching and Learning™

Discovery Kits: Electricity. 1.5 V Battery Batteries in series Closed switch Open switch V Motor Components.

THERMOMETER PROJECT PCB ASSEMBLY INSTRUCTIONS.

ASSEMBLING THE PCB – V3.914 Hold the PCB as shown below.

Electronic Schematics How we can draw electronic circuits.

PRACTICAL ELECTRONICS

How an NPN Transistor Works

Two basic types Ceramic disk Electrolytic Has positive and negative sides Farads – unit of measure (F) Microfarads(uF) and picofarads (pF) Cans have value.

IB Physics 12 Mr. Jean November 5 th, The plan: Video clip of the day More on circuits Looking through components.

Chapter 31 Fundamentals of Circuits (Circuit Elements and Diagrams & Kirchoff’s Laws and the Basic Circuit)

Electronic Component Markings How we distinguish between identical looking components.

Colorado Space Grant Consortium Gateway To Space ASEN / ASTR 2500 Class #06 Gateway To Space ASEN / ASTR 2500 Class #06.

IB Physics 12 Mr. Jean November 4 th, The plan: Video clip of the day Circuit diagrams Circuit symbols How to draw circuits.

ASSEMBLING THE PCB Have the PCB in front of you as shown. Make sure there are no copper tracks showing. This side is called the component side.

7. Direct Current circuits. 11 Find the currents, which flow in all the wires of the circuit in this figure 12  9 V 6 V b a cd 18 

Objective: 1.You will build a simple circuit - two transistor audio oscillator that will generate an audio tone in a speaker.

Physics 12 Mr. Jean November 13 th, The plan: Video clip of the day Drawing circuits Working with circuit diagrams Basic Ohm’s Law.

Electrical Circuits Making Electricity Useful Circuit Diagrams Electrical circuits can be shown in diagrams using symbols: 9.0V.

Circuits. The Basics The Symbols Wire Resistor Light Bulb Plug Battery Open Switch Closed Switch Capacitor.

An introduction to PIC’s for KS3 and KS4. Mr Rooks Hetton School.

Electronic Piano G H Patel College of Engineering & Technology G H Patel College of Engineering & Technology Prepared by Sanjay Hadiyal ( )

SeaPerch Electrical System. Electrical System Overview Assemble the control box. Make the Cat5 connector. Wire the motors to the tether. Wire the control.

Diode Foundations of Technology Diode © 2013 International Technology and Engineering Educators Association, STEM  Center for Teaching and Learning™ Foundations.

SeaPerch Electrical System

Fundamentals of Circuits

Electricity L1: Circuit Diagrams

Electronic Game.

Natural Sciences and Technology Grade 6

Simple Circuits Explained

ASSEMBLING THE TIMER Have the PCB in front of you as shown. Make sure there are no copper tracks showing. This side is called the component side.

You have 5 minutes to check the resistors you have done.

How a 555 Timer Works Objectives:

Be able to solder the capacitor and chip holder in place on the PCB.

Learn-to-Solder Exercise: Practice Flasher Circuit

How a Speaker Works.

How a PNP Transistor Works

Simple Circuit PHet.

Payload 2015 Class 9 By Jeff Dunker 5/19/ Beginner Payload.

Series Circuits.

Solder two wires as shown to bridge the cuts in the trace

SeaPerch Electrical System

Presentation transcript:

How To Make A Simple Circuit Speaker By: Brian Thomas, Dan Sampson, Brendan Dempsey, Ryan Boarder, Mikael Adane

Purpose To learn the basics of building a circuit and soldering and listening to music

Step 1 Add resistors to correct positions marked on circuit board and solder.

Step 2 Solder resistors to circuit board

Step 3 Make sure to clip excess wiring on resistors.

Step 4 Add capacitors to circuit board in correctly marked places and solder.

Step 5 Add the rest of the components to correct places and solder.

Step 6 Add battery pack and speaker to correct positions and solder.

Step 7 Put batteries in battery pack and press the tune select button

Troubleshooting

Step 8 Enjoy your pre-selected music!