BC Technology Education Association

Slides:

Advertisements

Similar presentations

By: Lindsay Myers. Gather wood (cherry, walnut, maple) Plane wood (walnut – 1/8 in, all else – ¾ in) Joint one side of each board Cut boards to width.

Advertisements

How to Make A Telegraph Exploring the Magic of Electricity.

HOW TO MAKE A ROCKET BY SAM CANNINGTON. THE FUSELAGE 1.Cut out a thin peace of cardboard.

Objective Define tools and materials used in agricultural engineering careers.

How I make a Peace Drum by Fred Haga in Clark County, Washington.

Tool Classification.

Manual Screwdrivers –used for driving screws into a material and/or taking out screws HAND TOOLS Hammer –used for driving nails into a material and/or.

In this activity we’ll discover the relationship between electricity and magnetism and find out just what makes a motor work. The electric motor converts.

Tools English for Careers Class. tool belt A tool belt is used to hold tools on your body.

Assembly 1 Calculate the amount of steel you will need by using CARD or a length of STRING to make a full scale model of your final solution. MEASURE and.

Pneumatic Clamp Step-by-step assembly instructions (c) 2010 National Fluid Power Association.

Drill, Tap, Die & Eye.

Mantle Clock. Beginning Steps Cut 2 piece 20 x 5 to make the 2 sides and top/bottom Cut 1 10 ¾ and 1- 9 from each 20 piece. This will make a side and.

Types of Wood Joints.

Planning Manufacture TaskEquipmentQC/QA Mark out the shape of the speaker front and back Tri square, pencil, ruler, tape measure.

Material Processing Material processing - changing the shape, size and/or characteristics.

1. b. Rip Saw 2. d. Used for cutting with the grain.

Building the Footstool P R O J E C T O V E R V I E W.

SMAW Tree, Plasma Cutting, and OAW Sculptures Plan of Procedure.

UNIT PROJECT #3 INTRODUCTION Day 2 Day 3 Day 4 Day 5 Day 6 Day 7 Day 8.

Agriscience Toolbox Plan of Procedure 1. Table Saw (equipment) Rip the bottom of the toolbox to a width of 10 inches.

Left side Right side Note pad Roll block. The Plan.

Building a Fixed Magnet DC Motor. Collect the Materials 4” wood Base 1 1/2 volt D Cell Toilet Paper Tube 6 Fixed Magnets18 AWG Enameled Wire Cellophane.

Step one: Page Border and title block. Border will be ¼” from the edge of the paper. Drawing will be done in landscape format. Title block will be 1”

MANUFACTURING. Storage of materials, mostly different types of woods.

H OW TO MAKE A TOMSON GUN By Rhys Leverington. S TEP Cut the base out this is going to be the bit that holds the barrel. Then start to.

Proposed Agriculture Courses Board of Education October 6, 2015.

Step On It: A Footstool Project Principles of Manufacturing Copyright © Texas Education Agency, All rights reserved 1.

How to mark out, cut, shape and finish. Marking Out For straight lines use a ‘scriber’ and an ‘engineers square’

Objective 6.03 Remember tools and their safety practices related to the agricultural mechanics industry.

How to Build a Divider Wall By Charysse Roberson.

AerE 423 Final Project Vertical Axis Wind Turbine Jake Krohn.

Session 2 Jigs and Formers

Bridge Project. Materials – 8 pieces of wood, glue, cutters, masking tape and a ruler.

By Christian Grecco. Drill Press 5. Hold material securely with a vice or clamps. 6. Be sure the chuck key is removed from the chuck before starting the.

Nathanael O’Hara. IDEAS I Researched Games Tables I liked these designs in part I decided to mesh the designs into something I liked and also could work.

BETHS PENCIL BOX. This is a pictures of my 250 mm piece of wood This is my piece of wood cut half way and I am about to chisel it!

ELECTRIC VEHICLE PROJECT CAR BUILDING PROCEDURES BY: PIERRE PEASHA CENTENNIAL HIGH SCHOOL BAKERSFIELD, CA.

"Cryptex Style" Maze Coin Puzzle

Tool List Presentation. Curved Claw Hammer Nail Set.

Tool Identification. TURNING TOOLS Turn nuts, bolts, and screws.

محافظة الدقهلية ادارة / دكرنس التعليمية مدرسة / كفر عبد المؤمن الاعدادية.

Pencil holder By Daniel van hees. 1.Sketch the out line of the pig in the wood. 2.Cut out the out line with a coping saw. 3.File the rough edges. 4.Sand.

Jr. Hi. Shop 2017 General tools.

Board Replacement for Engineered Glue-Down Pattern Plus with a Premier Performance replacement board.

Production Planning – Designing Tooling

Workshop Rotating Platform

Exploring the Magic of Electricity

Step-by-step assembly instructions

Workshop Rotating Platform

Workshop Rotating Platform

Unit 7 – Making a small Wooden Container

Step-by-step assembly instructions

Chapter 7: Proportions and Similarity

Ballista Project 2 120mm Axle hole 3 Nails 1 200mm

Volume of a prism Example Find the volume of the cuboid below 4.7cm

BC Technology Education Association

Industrial Technology Timber Stage 5

Decorative Gluing Project

Make a Two Note Wooden Whistle 1: Cut a piece of wood 20mm thick x 30mm wide to a length of 100mm. Use a back saw and a miter box to make the cut. 2: Use.

Ag Mechanics Tools.

Remember you can revise at home!

BC Technology Education Association

Fabric Terms Tx.8.

Print out label on Drill 2mm holes for magnets

Turning Between Centres

The CO2 Dragster TIJ 101 Upon finishing your brainstorming and Final Drawing (with dimensions and ruled lines) The following steps with be taken for fabrication.

Presentation transcript:

BC Technology Education Association www.bctea.org Iphone/ipad holder

BC Technology Education Association www.bctea.org Practice cuts

BC Technology Education Association www.bctea.org How to layout wood

BC Technology Education Association www.bctea.org How to clamp wood

BC Technology Education Association www.bctea.org How to cut diagonal piece

BC Technology Education Association www.bctea.org How to tape together

BC Technology Education Association www.bctea.org How to tape wood pieces together and layout holes

BC Technology Education Association www.bctea.org How to drill holes

BC Technology Education Association www.bctea.org How to cut to length

BC Technology Education Association www.bctea.org How to sand

BC Technology Education Association www.bctea.org Finished project