CL4NX +Cutter (KITTING MANUAL) 原　本 BARCODE PRINTER CL4NX +Cutter (KITTING MANUAL) WWCL05100: Cutter kit 13/Feb/2014 Production Engineering 2 Group Production Engineer Dept SATO TECHNOLOGY　CO.,LTD　 APPROVED CHECKED INCHARGE PE-E30A02

CL4NX +Cutter: KITTING MANUAL CUTTER UNIT RELAY PCB + CUTTER-CABLE SCREW (M3x6mm): 2pcs SCREW (M3x8mm): 4pcs FRONT PANEL (CT) SCREW (M4x10mm)-Black: 2pcs

CL4NX +Cutter: KITTING MANUAL <Preparation tool and Caution> Phillips screwdriver +No.2 Please turn OFF the power before assembling the cutter. <Assembly procedure> 1. Open the open-cover, and Open the Head 2. Remove (1) screw , and take-out (2) and (3) . 3. Connect (0) Option-cable and (5) Cutter-cable to (4) Relay-PCB 4. Fix (4) Relay-PCB by (6) screw 5. Attach (7) Front-cover, while passing thru Cutter-cable into Center-frame’s slot 6. Connect (5) Cutter-cable to PCB (of Cutter-unit) (3) FRONT COVER BOTTOM (LH) (2) BOTTOM (1) PAN SCREW SW+WL (MD3401428): 2pcs Reuse Disuse (0) OPTION CABLE Pull Option-cable Cutter-cable Relay-PCB Slide * This is Printer side item KIT items (5) CUTTER CABLE Cable set position KIT items (4) RELAY-PCB KIT items (6) PAN SCREW SW+WS (MD3300822): 2pcs Torque : 3.5～4.5 Kg･cm Reuse (7) FROTN COVER UNDER (LH)

CL4NX +Cutter: KITTING MANUAL 7. Attach (8) Cutter-unit to printer, fix it by (9) screw. 8. While opening the Cutter-open-lever, attach (10) Front-panel (CT), and fix it by (11) screw. KIT items Torque : 7.0～8.0 Kg･cm (9) PAN CREW SW+WL (MD3300822): 4pcs KIT items (8) CUTTER UNIT KIT items KIT items (10) FRONT PANEL (CT) (11) PAN SCREW SW+WL (MD3401028): 2pcs Torque : 14.0～16.0 Kg･cm <Check and adjust after assembly Cutter-kit> <Preparation> Set Label and Ribbon to printer. Close the Head Power ON the printer (press ｢Power｣ key). <Check contents> 1. Check Cutter-Open-Error (1) After opening the Cutter-open-lever, confirm that LCD-display is “Cutter-open-Error” message. (2) After checking, close and lock the Cutter-open-lever. Power Soft-R // Soft-L Enter Navigation Cutter-open-Error Open Cutter-open-lever

CL4NX +Cutter: KITTING MANUAL Power Soft-R // Soft-L Back Enter Navigation 2. Adjust of Cut-position In Offline, press the [Soft-R] key Printer loads one sheet label (blank), and cuts it. Confirm that cutting is on label gap. If NG (cutting on label), adjust the “Offset” value. <Adjust method of “Offset”> (1) Press ｢　　　｣, change “Online”  “Offline” (2) Press ｢Enter｣ key, display the “Settings” (3) Press ｢　　or ｣key several times Change Settings-menu: “Printing”  “Tools” Press ｢Enter｣ key (4) Select “Test Print”, press ｢Enter｣ (5) Select “Factory”, press ｢Enter｣ (6) Select “Offset”, Set “Offset” value In case of (A); Offset value  Reduce ( ) (B);  Increase ( ) (7) After setting, By press ｢Soft-R｣ key, printer is issued Test-printing. When Label-pitch is less than 100mm, Press ｢　　 ｣ x3 times, press the [Soft-R] key. Confirm the cutting position is OK or NG. If it was NG, please perform (6)~(7) again. Then If printing-position needs to adjust, please set it by “Pitch” value. OK (A) (B) NG Label loading direction // // Cutting position adjust Printing position adjust Test-print

CL4NX +Cutter: KITTING MANUAL <Packing method> 1. Remove Small-piece from Cushion (Bottom-Front) ~with Cutter model only Cushion (Top Front -L) Cushion (Top Rear) Cushion (Top Front -R) Cushion (Bottom-Rear) Modify the Cushion (Bottom-Front) +CT model only (1) CUSHION (BOTTOM-FRONT ) Carton-case Remove the Cushion piece from Cushion (Bottom-Front) * This small piece is not use for +CT model, please throw away it. Cushion (Bottom-Front): modified Cushion (Bottom-Rear) SLIT hole Printer direction (Top-Front –L) (Top-Front -R) (Top-Rear) Front Rear