1. Color Printer Training
Lanier LP116c
Color Printer Training

2. Terminology Main Output Tray Toner Cartridge Cover
Control Panel & Display Screen
Front Cover
Manual Feed Tray
Paper Tray 1

3. } More Terminology Side Cover Power Switch Right Side View
Rear/Back View
Side Cover
Power Switch

4. The Guts Fuser Transfer Roller Toner Cartridges
Printer Cartridges (Black & Color)
Waste Toner Cartridge

5. Changing Toner 3 1 2 4 Removing a Toner Cartridge
Place cartridge in appropriate color slot
Slowly push the cartridge toward the back until it locks into place
Replacing a Toner Cartridge
Pull the handle toward the front of the printer
Lift the cartridge straight up
*Replace only when Display Screen says “Add COLOR”

6. Print Cartridges Removing the Print Cartridges1. 2.
Removing the Print Cartridges
Unlatch the two green tabs across from each other
Lift up on the black bar
Press the green tab to the cartridge desired and pull it out 3.

7. Print Cartridges Replacing the Print Cartridges1. 2.
Replacing the Print Cartridges
Make sure the green arrow fits securely on the track before pushing the cartridge in
When the cartridge is slid into place, close the lock bar and snap the two green tabs on to secure it
*Replace only when the Display Screen says “Replace PCU”

8. Waste Toner Unlock the waste toner Pull the waste toner straight out2. 1.
Unlock the waste toner
Pull the waste toner straight out
Insert a new waste toner
Lock the new waste toner 3.
*Replace only when the Display Screen says “Replace Waste Toner” 4.

9. Paper Trays Loading the Manual Feed Tray1.
Loading the Manual Feed Tray
Open the Manual Feed (Bypass Tray) and fully extend the tray
Insert the paper and adjust the guides so they are snuggly against the paper
*Note the side that will be printed on is the face down side 2.

10. Paper Trays Change the paper size for the Bypass Tray
Press Menu and go to Paper Input and press “Enter#”
Go to Bypass Size and press “Enter#”
Choose paper size and press “Enter#”
*Note that the paper cannot exceed a width of 8.5 inches

11. Paper Trays Loading paper in Tray 1 (Default Tray)
Pull on the handle at the absolute bottom of the front
Remove the tray form the printer by lifting up as it is being pulled out
Open the width of the tray up all the way by holding the guides on the sides of the tray and moving them outward
Slide paper in from the back of the tray and tighten the paper guides snuggly against the paper
Return the tray to the bottom of the printer 3. 4.

12. When the printer is jammed it will display one of the following:
Jams? Where?
When the printer is jammed it will display one of the following:
Remove Misfeed A: Internal Path
Remove Misfeed B: Fuser Unit
Remove Misfeed Y: Paper Tray

13. Jam: Internal Path Fix 1.
If the jam does not come out easily, look at the lower right side and locate the letter A on the wall of the printer
Pull it down and remove the jam
Open the front cover
Locate the jam under the Fuser Unit (Caution: HOT!)
Slowly pull the jam out 4. 5.
2. – 3.

14. Jam: Fuser Unit Fix Open the front cover
CAUTION: Fuser is HOT!
Open the front cover
Lift the left and right “B1” blue levers on the fuser
Remove Jam 1. 2. 3. 4.
If the jam does not come out easily, pull “B2” down.
Remove Jam 5.

15. Jam: Paper Tray Fix Slowly pull the paper tray out Remove Jam1. 2.
Slowly pull the paper tray out
Remove Jam
Open the front cover and then close the front cover to reset the jam condition 3.