Lantern plans by Master Dafydd and Master Terafan

Slides:

Advertisements

Similar presentations

Decorative Clay Tiles and Plaques.

Advertisements

Basic Setting Out.

Start with a square piece of paper, the coloured side up. Fold in half one way, then open.

Gumball Machine Layout 7 th Grade Woods Project. What is The Technology Design Cycle?

A rectangular dog pen is constructed using a barn wall as one side and 60m of fencing for the other three sides. Find the dimensions of the pen that.

HIP JACK THEORY AND LAYOUT

Presentation 26: HIP RAFTER LAYOUT.

TOOL: Radial Arm Saw NEXT STEP: Radial Arm Saw RESULTS: Finish Top Apron Pieces at 9” L x 4” W x ¾ “ Th PROJECT Square Plant Stand PART Top Apron # NEEDED.

 What is joinery? In our case – we will be looking at the fastening or combining of two or more boards together when building our projects.  It is important.

Rotating Base Model Assembly Instructions copyright Mechanical Kits Ltd

Engineering Models 1 By: Ross King & Daniel Luddeke.

Bellwork Clickers A pair of parallel lines are revolved about an axis to make a pair of cones. What is the volume of the shell if the two lines look like.

Step-by-step assembly instructions

Left side Right side Note pad Roll block. The Plan.

This is a fold-down clothes bar that will hold up to 12 plastic clothes hangers or even more wire hangers. As I don’t have a trailer wall to put it on,

Woodwork Joints Introduction This unit will introduce various woodworking joints. You will be asked to manufacture some commonly used joints. Assessment.

Step one: Page Border and title block. Border will be ¼” from the edge of the paper. Drawing will be done in landscape format. Title block will be 1”

Levers & Fluids Rig Step-by-step assembly instructions (c) 2012 Mechanical Kits Ltd.

Tessellations You will need two pieces of computer paper and a small piece of thick paper and your final paper.

Flange Plates to be Welded to Beam Flanges.

Sam Krueger.  Entertainment Center  Preliminary design  Initial  36 plies, glass epoxy  [0 11 /±45 1 /90 5 ] s  No core  Modified design  36 plies,

{ MAKING ENVELOPES BY BY Mrs. Surekha B. Mali Mrs. Surekha B. Mali.

Coordinate Detector: prototype design General idea about the Coordinate Detector (CDET) so far: Three independent vertical planes with 15 cm plastic shield.

What simple machine is in a windmill? Prediction: Wheel or Gear.

Make a Model A box company makes boxes to hold popcorn. Each box is made by cutting the square corners out of a rectangular sheet of cardboard. The rectangle.

The cutting list should contain the following data: 1. PART No. I.e. 1, 2, 3, etc. 2. NAME a description of the part, eg. top 3. QUANTITY required, e.g.

STUDY & PRACTICE OF… ONE POINT PERSPECTIVE. Based on the way the human eye sees the world.

SIMPLE MACHINES INTRO TO TECHNOLOGY EXAMPLE.

Building Boxes What is the largest volume open top box that you can build from an 8 ½ by 11 inch sheet of paper?

Use of Modeling. Origami House Start off with an origami paper color side down.

How many of you know how to make an origami crane?

prepared by Mr.Grad©2004 Today you are going to start the assembly of your rocket, which you will launch at a later date.

Simple Machines By Skyler Peterson Wheel or Axle A wheel with a rod called an axle, through it’s center lifts or moves loads. A wheel with a rod called.

Foldable Tie Book Instructions. Materials Needed 2 pieces of scrap paper Glue stick Paper Hole Punch Tool 1 piece of yarn cut to one arm’s length.

Hand Sewing Stuffed Animals. Pin vs. Needle Pins have Heads Needles have an Eye.

Completed Front and Rear Standard 10 ½” 1 ½” 3 ¼” 4 ½” 1” ¾” 1 ½” 6” ¾” Channel Length: 5 ¼”, ¾” from end.

Board Replacement for Engineered Glue-Down Pattern Plus with a Premier Performance replacement board.

Global Exotics Board Replacement

Build-It-blocks Creative Robotics

Start on the corner of your picture *(Not the corner of the paper)

The size of a surface in square units

Workshop Rotating Platform

Workshop Rotating Platform

Exploring the Magic of Electricity

Step-by-step assembly instructions

Workshop Rotating Platform

Step-by-step assembly instructions

Lay two pieces of paper on top of each other. Fold paper “hotdog”.

Terafan Greydragon’s Bench design

Step-by-step assembly instructions

Step-by-step assembly instructions

Workshop Rotating Platform

Fold Your Own Bank Activity

Jute Padding 1974 TCS before removal

Column addition and subtraction

Board Replacement for Engineered Glue-Down Hardwood Floors

Step-by-step assembly instructions

Master Terafan Greydragon’s Bench design

Column addition and subtraction

Ballista Project 2 120mm Axle hole 3 Nails 1 200mm

Drawing of stud.

3.6 Mathematical Models: Constructing Functions

2.7 Mathematical Models: Constructing Functions

Master Terafan Greydragon’s Bench design

Decorative Gluing Project

Make a Two Note Wooden Whistle 1: Cut a piece of wood 20mm thick x 30mm wide to a length of 100mm. Use a back saw and a miter box to make the cut. 2: Use.

8” MCP Flow for 8/7/ and -003 coated at Fermi and returned to ANL on 8/3/ and -050 packed and ready for Fermi courier to.

2.7 Mathematical Models: Constructing Functions

Presentation transcript:

Lantern plans by Master Dafydd and Master Terafan 5.75” 3.5” 3 1/8” 2.5” 3 1/8” 2.5” 3.5” 5.75” Base for lifting the candle/lamp up for lighting/refilling 4 decorative side pieces (1/4” thick) Top 3/4” Glass for the sides 3.5” x 6” (4 pieces) 8” 6” 4.75” 4 square corner columns with grooves cut 4.75” 1/4” wooden dowel Bottom

4 square corner columns with grooves cut in two sides 5.75” Screw holes Groove for glass Groove for decorative side 2.5” 5.75” Holes for the rope Groove for the glass runs the length of the column Hole for the lifting dowel Top The hole in the center (of the top) must be large enough for your lamp/candle to be taken out. Groove for the decorative side only goes 3.5” down Glass Decorative side 4.75” 4.75” 4 square corner columns with grooves cut in two sides Bottom