1. Trimmer Auto Switch (Sensor unit) D-M9K Series

2. Conventional product Rail Mounting(D-F7K) CQ2(  12 to  160) Fit to the round groove Conventional style: Rail mounting or direct mounting to square groove. Conventional style: Rail mounting or direct mounting to square groove. (M3 x 0.5 x 10L) Auto switch mounting screw Auto switch spacer Auto switch mounting nut New model of Direct Mounting (D-M9K) CQ2(  12 to  200) Mounting screw (M2.5 x 12L) Mounting bracket not required!! 1. Features

3. One switch for two outputs. Two positions can be set by trimmers within setting range. Two positions can be set by trimmers within setting range. OUT1 and OUT2 are adjustable separately Output ON=Green LED is ON. OUT1 Detecting range OUT2 Detective range Output ON=Orange LED is ON. Small work piece Medium work piece Large work piece Operating range of sensor (LED of sensor is ON) OUT1 TrimmerOUT2 Trimmer Minimum width to detect 0.5mm Adjustable by trimmer Minimum width to detect 0.5mm 1. Features

4. Sensor and amplifier can be replaced independently. Amplifier is D-RNK/D-RPK. Sensor and amplifier are assembled by a connector, so they are independently replaceable. Sensor unit Housing Amplifier unit: D-RNK/D-RPK Lever 1. Features

5. IP67(Sensor unit) IP40 for amplifier IP40 for amplifier 2 ways for mounting (Amplifier unit ) DIN rail mounting Direct mounting M3 x 16L Washer

6. 2. Objective Provide trimmer switch suitable for the actuator round groove. Develop a switch which can perform positioning using trimmer so users do not have to adjust the switch position. For quick check of the workpiece size, conventional product makes fine adjustment of the auto switch. New product can set the detected position by amplifier trimmer without fine adjustment of the switch.

7. 3. Application examples ① To check height of a work piece Orange LED is ON. OUT2 Optimum Low High OUT1 Green LED is ON. OUT1 OUT2 Orange LED is ON.

8. (2) Verify workpiece size Orange LED is ON. OUT2 Large work piece Medium work piece Orange LED is ON. OUT2 OUT1 Green LED is ON. Small work piece OUT1 Green LED is ON. No work piece OUT1 Green LED is OFF. OUT2 Orange LED is OFF. 3. Application examples

9. Model D-M9K Mounting Round groove mounting Applicable ampliier unit D-RNK, D-RPK Indicator lamp Red lights on at sensitive position Green lights on at optimum detecting position Electrical entry Grommet Lead wire Oil-proof vinylcabtire cord f3.5 、 AWG26 4 cores Impact resistance 980m/s 2 Enclosure IP67 Insulation resistance 50M  or more at 500 VDC Mega (between case and lead wire) Withstand voltage 1000VAC 1minute (between case and lead wire) Ambient temperrature -10 to 60  C Note) Amplifier is conventional part. Please refer to the catalog for details. 4. Specifications

10. ・ Air Grippers Applicable Actuators and Operation Range Note) Use D-Y7K when MHS series (ø32 or larger) is used. Model Bore size(ø) 1620253240506380100125 MHZ2 3.05.56.58.07.5-N/A MHZJ2 3.05.56.5-N/A MHS2 -4.0 *-N/A MHS3 -5.04.0* MHS4 -5.03.0*-N/A 4. Specifications

11. ・ Air Cylinders Note 1) Values shown as the auto switch operating range used for the air grippers include the range on both finger opening ends. Note 2) The operating range is provided as a guideline including hysteresis, it cannot be guaranteed (assuming approximately  30% dispersion). It may vary substantially depending on environment. Model Bore size (ø) 121620253240506380100125140160180200 CQ2-Z3.54.5 5.05.55.0 6.0 7.5 8.07.0 CQM3.54.04.5 5.0 6.05.56.0-N/A RZQ- N/ A 5.0 5.5-N/A MK-Z3.03.5 4.04.54.04.5 -N/A MGP-Z3.55.04.55.05.5 -N/A 4. Specifications

12. 5. Comparison with competitor Company nameSMCManufacturer B Applicable Actuators Air GripperAir Cylinder Equivalent to MHZ2 Equivalent to CQ2 MHZ2,MHZJ2 MHS2,MHS3, MHS4 CQ2-Z,CQM RZQ,MK-Z MGP-Z Power supply voltage DC12 ～ 24V DC24V Output style 2 output within operating range 2 output 1-5V in 8mm which customer specified Effective measurable range Depends on the actuator (5.0mm when CQ2 ø25) 80% or more of the hand full stroke 8mm Note1) Repeatability+/-0.2mm+/-0.1mm Cord length between sensor and amplifier 3m2m Connection between sensor and amplifier Connector (e-con)M8 connector Note1) A switch is required to detect the operating range.

13. 6. How-to-Order D- M9 K Trimmer switch Series : Additional models SymbolSpecifications M9Sensor for round groove F7Sensor for rail mounting Y7Sensor for square groove RNAmplifier NPN output RPAmplifier PNP output

14. 7. Dimensions Most sensitive position

15. 8. Handling precautions Required tightening torque The tightening torque for a hexagon socket head cap screw (M2.5 x 12L) is 0.1 to 0.2Nm. Hold the shorter side of a hexagon wrench, and turn it to tighten.