1. Logic synthesis flow Technology independent mapping –Two level or multilevel optimization to optimize a coarse metric related to area/delay Technology dependent mapping –More “concrete” synthesis: map logic function to a given library, typically with characterized areas and delays –Represent circuit by a subject graph –Represent library cells by a set of pattern graphs –(These graphs are always directed acyclic graphs (DAG’s) for combinational circuits) –Find optimal mapping of pattern graphs to the subject graph to optimize a cost function

2. Example library and its pattern graphs INV (2) NAND2 (4) NAND4 (8) NAND3 (6) AOI21 (6) AOI22 (8) XOR2 (12) Nodes: 2NAND NOT (input permutations not shown) or Cost of using the gate, taken here as the number of transistors

3. Example circuit Subject graph

4. Two possible mappings Cost = 2  Cost(NAND2)+2  Cost(INV) +Cost(NAND4)+Cost (NAND3) = 2  4 + 2  2 + 8 + 6 = 26 Cost = Cost(NAND2)+Cost(INV) +Cost(AOI21)+2  Cost (NAND3) = 4 + 2 + 6 + 2  6 = 24 NAND2 INV NAND3 NAND4 NAND3 INV NAND2 AOI21

5. Tree mapping Applicable to “fanout-free” regions and provably optimal Simple objective: minimize area –Cost is fanout-independent –Things are more tricky when costs are fanout-dependent Basic idea –Traverse from inputs to outputs –At each node Enumerate all mappings of the node and find cost Choose lowest cost solution based on node cost and sum of input costs –Optimal substructure property: any optimal solution can be formed by using the optimal solutions at previous nodes

6. Tree mapping: an example Cost = 4 Cost = 2+4=6 Cost = 4 Cost = min(10,14) = 10 Cost = 2+10=12 Cost = min(4+12+0,6+6+4+0,8+0+4+0) = 12 NAND2 NAND3 NAND4 Mapped as NAND2 Cost = Cost(NAND2)+  Cost(fanins) = 4+6+4 = 14 Mapped as NAND3 Cost = Cost(NAND3)+  Cost(fanins) = 6+0+4 = 10

7. Finer points Handling inversions better –Introduce a buffer element (two inverters) with cost 0 into library –Replace inverter-free edges in subject graph by a pair of inverters –Make appropriate (similar) minor changes to pattern graphs –Map as before –Advantage: allows inversions to be considered; any inversions not used are replaced by buffers with cost zero during mapping Mapping DAGs –DAG mapping is NP-complete for area objectives –Intuition: at multi-fanout points, contradictory optimal choices can be made; can only be resolved by logic duplication –Heuristic: decompose DAG into a forest of trees and map each optimally

8. Circuit decomposition Quality of mapping depends on decomposition of circuit –2NAND/NOT and AND/OR/NOT decompositions used most often –Number of such decompositions is huge! Clever way of considering all decompositions proposed by Lehman, Watanabe, Grodstein and Harkness, IEEE Transactions on CAD 8/1997, pp. 813-834

9. Other objective functions Minimizing area considered – seen to be easy Minimizing delay is more complex, since delay is fanout- dependent Basic procedure for tree-mapping –Traverse graph as before –Store several best solutions at each node, parameterized by load capacitance values (i.e., store best solution for several load caps) –This also allows mapper to use various power levels available for each cell in the library

10. Other objective functions (contd.) Minimize Area subject to Delay  D spec Basic dynamic programming procedure –Traverse tree as before –Find all (Area,Delay) choices at each node –(For fanout-dependent delay, parameterize delay by fanout cap) –Remove provably suboptimal (Area,Delay) subsolutions If Area 1  Area 2 and Delay 1  Delay 2 (clearly one inequality must be strict!), then any optimal solution will prefer (Area 1,Delay 1 ) to (Area 2,Delay 2 ) Can prune the latter from the list Pictorially Delay Area This point is provably worst than this one

11. Final note on synthesis Deep submicron technologies (< 0.25 micron or so): –Wire capacitances are significant –Interconnect significantly affects circuit performance Traditional wire-load models –Fanout load depends on # fanouts, calculated statistically –Invalid in deep submicron since fanout RC’s depend on locations and not just number of fanouts Physical synthesis –Concurrently perform placement and synthesis –Common approach Create “physical prototype” – coarse placement Perform synthesis according to this placement; refine placement as you go along