1. Skilled Trades / Res. Cons’t. Drill Press Mr. Mark Shortall / Technology Department

2. Drill Press

3. We can use a drill press for drilling through holes and blind holes. We can use a drill press for drilling through holes and blind holes. With attachments it can be used for drum sanding as well as making a mortise. With attachments it can be used for drum sanding as well as making a mortise. In Skilled Trades & Residential Construction we will use our drill press for drilling operations only In Skilled Trades & Residential Construction we will use our drill press for drilling operations only

4. Drill Press

5. Safety Always obtain the teachers permission prior to using the Drill Press. Always obtain the teachers permission prior to using the Drill Press. Do not wear gloves, tie or loose fitting clothing. Remove rings, watch and other jewelry, and roll up sleeves, tie back long hair. Do not wear gloves, tie or loose fitting clothing. Remove rings, watch and other jewelry, and roll up sleeves, tie back long hair. Guards should always be in place at all times. Guards should always be in place at all times.

6. Safety Clamp work to the table if it is too short to contact the column. Clamp work to the table if it is too short to contact the column. Hold material securely with a vise or clamps. Hold material securely with a vise or clamps. Clamp all work when using a hole saw or any cutting tool larger than ½" dia. Clamp all work when using a hole saw or any cutting tool larger than ½" dia.

7. Safety Do not exceed recommended speed for the drill, accessory, and workpiece material. Do not exceed recommended speed for the drill, accessory, and workpiece material. Be sure chuck key is removed from the chuck before starting the drill press. Be sure chuck key is removed from the chuck before starting the drill press. Make all adjustments with the power off. Make all adjustments with the power off. Adjust the table depth stop to avoid drilling into the table. Adjust the table depth stop to avoid drilling into the table.

8. Safety Be sure drill bit or cutting tool is securely locked in the chuck. Be sure drill bit or cutting tool is securely locked in the chuck. Disconnect drill from the power source when making repairs. Disconnect drill from the power source when making repairs. Shut off power, remove the drill bit or cutting tool, and clean the table before leaving the machine. Shut off power, remove the drill bit or cutting tool, and clean the table before leaving the machine.

9. Drill Press

10. Safety Quiz Make All adjustments with the power off ……… TF Make All adjustments with the power off ……… TF To avoid drilling into the table you should adjust the table depth stop ……………………………………….. TF To avoid drilling into the table you should adjust the table depth stop ……………………………………….. TF A good place to store the chuck key when not in use is to leave it in the chuck ……………………………… TF A good place to store the chuck key when not in use is to leave it in the chuck ……………………………… TF It is okay to adjust the motor speed of the drill press while it is turned on …………………………………. TF It is okay to adjust the motor speed of the drill press while it is turned on …………………………………. TF Disconnect drill from power source when making repairs Disconnect drill from power source when making repairs...................................................................... TF

11. Safety Quiz Clamp work to table if it is too short to reach the column ………………………………………………………………. TF Clamp work to table if it is too short to reach the column ………………………………………………………………. TF Always set the drill press to its top RPM no matter what type of material you are drilling ……………….. TF Always set the drill press to its top RPM no matter what type of material you are drilling ……………….. TF Clamp all work when using a hole saw or a drill bit larger than ½” ………………………………………………… TF Clamp all work when using a hole saw or a drill bit larger than ½” ………………………………………………… TF Guards should always be kept in place at all times ……………………………………………………………… TF Guards should always be kept in place at all times ……………………………………………………………… TF If you are finished with the drill press it is okay to leave your bit in the chuck in case someone else wants to use it …………………………………………………………… TF If you are finished with the drill press it is okay to leave your bit in the chuck in case someone else wants to use it …………………………………………………………… TF

12. Safety Quiz Make All adjustments with the power off ……… TF Make All adjustments with the power off ……… TF To avoid drilling into the table you should adjust the table depth stop ……………………………………….. TF To avoid drilling into the table you should adjust the table depth stop ……………………………………….. TF A good place to store the chuck key when not in use is to leave it in the chuck ……………………………… TF A good place to store the chuck key when not in use is to leave it in the chuck ……………………………… TF It is okay to adjust the motor speed of the drill press while it is turned on …………………………………. TF It is okay to adjust the motor speed of the drill press while it is turned on …………………………………. TF Disconnect drill from power source when making repairs Disconnect drill from power source when making repairs...................................................................... TF

13. Safety Quiz Clamp work to table if it is too short to reach the column ………………………………………………………………. TF Clamp work to table if it is too short to reach the column ………………………………………………………………. TF Always set the drill press to its top RPM no matter what type of material you are drilling ……………….. TF Always set the drill press to its top RPM no matter what type of material you are drilling ……………….. TF Clamp all work when using a hole saw or a drill bit larger than ½” ………………………………………………… TF Clamp all work when using a hole saw or a drill bit larger than ½” ………………………………………………… TF Guards should always be kept in place at all times ……………………………………………………………… TF Guards should always be kept in place at all times ……………………………………………………………… TF If you are finished with the drill press it is okay to leave your bit in the chuck just case someone else wants to use it …………………………………………………… TF If you are finished with the drill press it is okay to leave your bit in the chuck just case someone else wants to use it …………………………………………………… TF

14. Skilled Trades / Res. Cons’t. Drill Press Mr. Mark Shortall / Technology Department