Presentation is loading. Please wait.

Presentation is loading. Please wait.

Corning Cabelcon 1. 2 To begin with – we need some tools… Cable cutter Cabelcon Rotary Stripper Mounting tool Compression tool Please read the instructions.

Similar presentations


Presentation on theme: "Corning Cabelcon 1. 2 To begin with – we need some tools… Cable cutter Cabelcon Rotary Stripper Mounting tool Compression tool Please read the instructions."— Presentation transcript:

1 Corning Cabelcon 1

2 2 To begin with – we need some tools… Cable cutter Cabelcon Rotary Stripper Mounting tool Compression tool Please read the instructions before using the tools! Rubber tool

3 Corning Cabelcon 3 Lets start to work… First step is to cut your cable using a proper cable cutter.

4 Corning Cabelcon 4 Screws for adjustment of blades Hex tool for adjustment Strip your cable… Insert the cable into the cable stripper as shown… Attention: Please make sure to adjust the tool blades for your cable dimensions before using it for the first time! Please read instructions supplied with the tool.

5 Corning Cabelcon 5 Strip your cable… Turn the stripper clockwise 4-5 times…

6 Corning Cabelcon 6 Strip your cable… - and pull to remove the scraps…

7 Corning Cabelcon 7 Strip your cable… Optional: You can check the stripping dimensions against the guide printed on the connectors 6,5 + 6,5 mm (¼ + ¼)

8 Corning Cabelcon 8 Prepare your cable… Fold exposed braid over the jacket. Leave the inner foil attached to the dielectric and make sure that the foil is undamaged and smooth. For Quad shield, Tri shield and Super shield cables: Remove the outer braid and foil only. Fold back the inner braid.

9 Corning Cabelcon 9 Mount the connector… Use of the Rubber Tool will ensure an excellent grip on the cable! * Press the front part of the connector (with the built-in tool) against the cable and turn it slowly to prepare the foil to enter into the connector. (* Optional operation – normally not necessary if Corning Cabelcons Rotary Cable Stripper has been used)

10 Corning Cabelcon 10 Push the connector over the foil and allow the support mandrel to slide between the foil and braid… Mount the connector… A mounting tool can be used to ensure a better grip on the connector…

11 Corning Cabelcon 11 Press and turn until the dielectric is flush with the support mandrel face Mount the connector…

12 Corning Cabelcon 12 Compress the connector… 1) Insert your connector/cable into the tool with the tool handle in open position… 2) Apply a downward pressure on the cable to allow the split jaws to secure the cable… Click!

13 Corning Cabelcon 13 - and close the tool handle completely insuring the connector sleeve is fully compressed (white plastic is invisible). Compress the connector… Before compression After compression

14 Corning Cabelcon 14 Open the tool - press the outside split-jaw tabs and pull out the connector assembly… Take out the connector…

15 Corning Cabelcon 15 Compression completed The finest connection available!

16 Corning Cabelcon 16 More tools available… Other types of tools are available. A few examples: Corning Cabelcon universal CX3 compression tools Universal tool for RG6/59 and RG11 Various installation tools Please checkout our website for more information

17 Corning Cabelcon 17 Finally some good advice… In order to avoid decreased network performance, we recommend the use of a torque wrench to ensure proper tightening of your connectors

18 Corning Cabelcon 18 January 2008


Download ppt "Corning Cabelcon 1. 2 To begin with – we need some tools… Cable cutter Cabelcon Rotary Stripper Mounting tool Compression tool Please read the instructions."

Similar presentations


Ads by Google