1. 제조사 MODEL NAME SYMETRIX EDGE Open Architecture D.S.P Processors: 1 x Analog Devices SHARC 21489 @ 400 MHz SIMD. Raw processing capacity: 400 MIPS, 1.6 GFLOPS. Sampling Rate: 48 kHz, ± 100 ppm. Frequency Response (A/D/A): 20 Hz – 20 kHz, ± 0.5 dB. Dynamic Range (A/D/A): > 114 dB, A-weighted. Channel Separation (A/D/A): > 108 dB @ 1 kHz, +24 dBu. Latency (A/D/A): 0.88 mS, inputs routed to outputs. Delay memory: 80 mono seconds. Analog control inputs: 0-3.3 VDC. Recommended external control potentiometer: 10k Ohm, linear. Logic outputs: Low (0V) when active, pulled high (5V) when inactive. Logic output maximum external power supply voltage: 24 VDC. Logic output maximum external power supply current sinking: 50 mA. Logic output maximum output current: 10 mA. RS-232 accessory serial I/O: 38.4 kbaud (default), 8 data bits, 1 stop bit, no parity, no flow control wired straight-through, only pins 2, 3, and 5 required. RS-485 serial I/O: 38.4 kbaud (default) 8 data bits, 1 stop bit, no parity, no flow control. May be broken out of ARC port. Ethernet Cable: Standard CAT5, maximum device to device length = 100 meters. Dante Cable: Standard CAT6, maximum device to device length = 100 meters. ARC Cable: Standard CAT5, distance dependent upon load and number of devices. Maximum devices per system: 32 units per Site File. Maximum stored presets: 1000. Four configurable I/O card slots, up to 16 channels total of local I/O plus 128 (64x64) channels of Dante network audio. Operating Temperature : 30°C Power: 100-240 VAC, 50/60 Hz, 45 w Dim(WxHxD): 480.2 x 43.7 x 241.3mm(1U) Shipping Weight: 5.9kg

2. 제조사 MODEL NAME SYMETRIX 4ch AEC INPUT EDGE Option Card 4Channel AEC Input card Number of Inputs: Four (4) acoustic echo cancellation. Connectors: 3.81 mm terminal blocks. Nominal Input Level: +4 dBu with 20 dB of headroom. Maximum Input Level: +23 dBu. Mic Pre-amp Gain: 0, 11.8, 24, 44 or 54 dB switchable with ± 24 dB trim. Mic Pre-Amp EIN: <-127dB with 150 Ohm source impedance. CMRR: > 76 dB @ 1 kHz, unity gain. Input Impedance: 8k Ohms balanced, 4k Ohms unbalanced. Phantom Power: +20 VDC @ 10 mA maximum. A/D Dynamic Range: < 115 dB, A-weighted. A/D Latency: 0.28 mS (direct), 11 mS (AEC enabled). A/D THD + Noise: < -94 dB, unweighted Tall Length: >250mS. Convergence Time: >100dB/S. Shipping Weight: 0.45kg

3. 제조사 MODEL NAME SYMETRIX 4ch Analog MIC/LINE INPUT EDGE Option Card 4 Channel analog input card Number of Inputs: Four (4) switchable balanced mic or line level. Connectors: 3.81 mm terminal blocks. Nominal Input Level: +4 dBu with 20 dB of headroom. Maximum Input Level: +23 dBu. Mic Pre-amp Gain: 0, 11.8, 24, 44 or 54 dB switchable with ± 24 dB trim. Mic Pre-Amp EIN: < -127dB with 150 Ohm source impedance. CMRR: > 76 dB @ 1 kHz, unity gain. Input Impedance: 8k Ohms balanced, 4k Ohms unbalanced. Phantom Power (per input): +48 VDC @ 10 mA maximum. Dynamic Range: > 115 dB, A-weighted. THD + Noise: < -94 dB, unweighted; 1 kHz @ +22 dBu with 0 dB gain. Latency: 0.28 mS. Shipping Weight: 0.45kg

4. 제조사 MODEL NAME SYMETRIX 4ch Analog MIC/LINE OUTPUT EDGE Option Card 4Channel analog output card Number of Outputs: Four (4) balanced line level. Connectors: 3.81 mm terminal blocks. Nominal Output Level: +4 dBu with 20 dB of headroom. Maximum Output Level: +24 dBu (+22.8 dBu into a 2k Ohm minimum load). Output Impedance: 300 Ohms balanced, 150 Ohms unbalanced. Dynamic Range: > 117 dB, A-weighted. THD + Noise: < -95 dB, unweighted; 1 kHz @ +22 dBu with 0 dB gain. Latency: 0.60 mS. Shipping Weight: 0.45kg

5. 제조사 MODEL NAME SYMETRIX 4ch Digital INPUT EDGE Option Card 4Channel digital input card Number of Inputs: Two (2) pairs of switchable AES or S/PDIF format (4 channels total). Connectors: 3.81 mm terminal blocks. Nominal Input Level: -20 dBFS (+4 dBu with 20 dB of headroom). Maximum Input Level: 0 dBFS (+24 dBu). Input Impedance: 110 Ohms (AES), 75 Ohms (S/PDIF). Dynamic Range: > 128 dB, unweighted. THD + Noise: < -125 dB, unweighted. Nominal Sample Rate: 48 kHz. Sample Rate Sync Range: 12 to 96 kHz. Latency: 2.1 mS @ 48 kHz. Shipping Weight: 0.45kg

6. 제조사 MODEL NAME SYMETRIX 4ch Digital OUTPUT EDGE Option Card 4Channel digital output card Number of Outputs: Two (2) pairs of switchable AES or S/PDIF format (4 channels total). Connectors: 3.81 mm terminal blocks. Nominal Output Level: -20 dBFS (+4 dBu with 20 dB of headroom). Maximum Output Level: 0 dBFS (+24 dBu). Output Impedance: 110 Ohms (AES), 75 Ohms (S/PDIF). Dynamic Range: > 128 dB, unweighted. THD + Noise: < -125 dB, unweighted. Nominal Sample Rate: 48 kHz. Sample Rate Sync Range: 12 to 96 kHz. Latency: 2.1 mS @ 48 kHz. Shipping Weight: 0.45kg

7. 제조사 MODEL NAME SYMETRIX 2 LINE ANALOG TELEPHONE INTERFACE EDGE Option Card 2 Line analog telephone interface card Telco “Line” Connector : RJ11. Format: POTS (plain old telephone service) or analog extension from a PBX. Telco “Set” Connector: RJ11. Format: POTS (plain old telephone service) or analog extension from a PBX. Note: Relay bridged to Line port with option in software to isolate based on hook status. Frequency Response : 250 Hz to 3.3 kHz ±1.0 dB THD+N : < 0.3% Signal to Noise Ratio : > 62 dB LEC Tail Time : 32 mS Null : 55 dB nominal. Compliance : G.165, G.168 compliant. Tx Level : -10.0 dBm RMS average; +3.2 dBm maximum. Rx Level : -10.0 dBm RMS average; +3.2 dBm maximum. Transhybrid Loss : > 48 dB with LEC enabled. Ringer Equivalency Number : 0.0 dB Shipping Weight : 0.45 kg

8. 제조사 MODEL NAME SYMETRIX xIN 12 Open Architecture D.S.P 12 mic/line inputs Sampling Rate: 48 kHz, ± 100 ppm. Frequency Response (A/D): 20 Hz – 20 kHz, ± 0.5 dB. Channel Separation (A/D): > 111 dB @ 1 kHz, +24 dBu. Dante Cable: Standard CAT6, maximum device to device length = 100 meters. Connector: 3.81 mm terminal blocks. Number of inputs: 12 switchable balanced mic or line level. Nominal input level: +4 dBu with 20 dB of headroom. Maximum input level: +23 dBu. Mic pre-amp gain: 0, 11.8, 24, 44 or 54 dB switchable. Mic pre-amp EIN: < -127 dB with 150 Ohm source impedance. CMRR: > 76 dB @ 1 kHz, unity gain. Input impedance: 8k Ohms balanced, 4k Ohms unbalanced. Phantom power (per input): +48 VDC @ 10 mA maximum. Dynamic range: > 116 dB, A-weighted. THD + Noise: < -100 dB, unweighted; 1 kHz @ +22 dBu with 0 dB gain. Latency: 0.28 mS. Operating Temperature: 30°C Power: 100-240 VAC, 50/60 Hz, 25 w Dim(WxHxD): 480.2 x 43.7 x 241.3mm(1U) Shipping Weight: 5.4kg

9. 제조사 MODEL NAME SYMETRIX RADIUS 12x8 Open Architecture D.S.P Analog Inputs: Twelve (12) switchable balanced mic or line level. Analog Outputs: Eight (8) balanced line level. Processors: 1 x Analog Devices SHARC 21489 @ 400 MHz SIMD. Raw processing capacity: 400 MIPS, 1.6 GFLOPS. Sampling Rate: 48 kHz, ± 100 ppm. Frequency Response (A/D/A): 20 Hz – 20 kHz, ± 0.5 dB. Dynamic Range (A/D/A): > 114 dB, A-weighted. Channel Separation (A/D/A): > 108 dB @ 1 kHz, +24 dBu. Latency (A/D/A): 0.88 mS, inputs routed to outputs. Delay memory: 80 mono seconds. Analog control inputs: 0-3.3 VDC. Recommended external control potentiometer: 10k Ohm, linear. Logic outputs: Low (0V) when active, pulled high (5V) when inactive. Logic output max. external power supply voltage/Current sinking: 24VDC/50 mA. Logic output maximum output current: 10 mA. THD + Noise: < -85 dB (unweighted); 1 kHz @ +22 dBu with 0 dB gain. RS-232 accessory serial I/O: 57.6 kbaud (default), 8 data bits, 1 stop bit, no parity, no flow control wired straight-through, only pins 2, 3, and 5 required. RS-485 serial I/O: 38.4 kbaud (default) 8 data bits, 1 stop bit, no parity, no flow control. May be broken out of ARC port. Ethernet Cable: Standard CAT5, maximum device to device length = 100 meters. Dante Cable: Standard CAT6, maximum device to device length = 100 meters. ARC Cable: Standard CAT5, distance dependent upon load and number of devices. Maximum devices per system: 32 units per Site File. Maximum stored presets: 1000. 12 mic/line inputs, 8 outputs. Operating Temperature : 30°C Power: 100-240 VAC, 50/60 Hz, 45 w Dim(WxHxD): 480.2 x 43.7 x 241.3mm(1U) Shipping Weight: 5.9kg

10. 제조사 MODEL NAME SYMETRIX xOUT 12 Open Architecture D.S.P 12 line outputs Sampling Rate: 48 kHz, ± 100 ppm. Frequency Response (D/A): 20 Hz – 20 kHz, ± 0.5 dB. Channel Separation (D/A): > 111 dB @ 1 kHz, +24 dBu. Dante Cable: Standard CAT6, maximum device to device length = 100 meters. Connector: 3.81 mm terminal blocks. Number of outputs: Twelve (12) balanced line level. Nominal output level: +4 dBu with 20 dB of headroom. Maximum output level: +24 dBu (+22.8 dBu into a 2k Ohm minimum load). Output impedance: 300 Ohms balanced, 150 Ohms unbalanced. Dynamic range: > 118 dB, A-weighted. THD + Noise: < -105 dB, unweighted; 1 kHz @ +22 dBu with 0 dB gain. Latency: 0.60 mS. Operating Temperature: 30°C Power: 100-240 VAC, 50/60 Hz, 25 w Dim(WxHxD): 480.2 x 43.7 x 241.3mm(1U) Shipping Weight: 5.4kg

11. 제조사 MODEL NAME SYMETRIX ARC-2e Adaptive Remote Control Menu-driven wall panel remote for Symetrix D.S.P 8-character backlit display supports up to 31 scrolling characters. Instant user feedback for control assignments, default settings, and actions. Three buttons navigate menus, change values, and enable or disable the remote control. All control assignments, including item labeling, parameter limits and firmware version upgrades are handled by software included with Symetrix DSP hardware. Processor: Atmel ATmega 128 Field-Upgradeable Firmware: Yes Number of Menus: 24 Enumerations per Menu: 16 Menu Range Limits: Yes Max. Characters per Menu Name: 31 Maximum Number of Strings: 255 Maximum Operating Voltage: 30 VDC

12. 제조사 MODEL NAME SYMETRIX ARC-K1e Adaptive Remote Control Rotary encoder remote with two-bank push-button knob. 8-segment LED ladder with push-button encoder can control one or two parameters. Power, control, and a single channel of ARC Audio are connected via RJ-45 inputs. Supports “idle” mode for light-sensitive environments like theaters. Hardware lockout pins are provided to accommodate an installer supplied key switch. Software and hardware lockout functions can be independently programmed. Furnished with a standard white single gang Decora® faceplate and splash resistant overlay.

13. 제조사 MODEL NAME SYMETRIX ARC-SW4e Adaptive Remote Control Four push-button wall panel remote. Four switches are programmable as momentary, latched or radio buttons with tri-color LEDs. Power, control, and a single channel of ARC Audio are connected via RJ-45 inputs. Supports “idle” mode for light-sensitive environments like theaters. Hardware lockout pins are provided to accommodate an installer supplied key switch. Software and hardware lockout functions can be independently programmed. Furnished with a standard white single gang Decora® faceplate and splash resistant overlay.

14. 제조사 MODEL NAME SYMETRIX ARC-EX4e Adaptive Remote Control Push-button remote expansion panel. Remote wall panel expansion device for use with ARC-K1e and ARC-SW4e. For expansion, add up to four ARC-EX4e to each ARC-K1e and up to three ARC-EX4e to each ARC-SW4e. Cost effective way to expand remote control capabilities. Not for use with ARC-2e. Splash resistant overlay.