1. Cisco Systems Networking Academy S2 C 12 Routing Protocols

2. Setup Mode Initial Configuration –No valid startup-config –System load ends with setup mode –Use system configuration dialogue to setup Result is minimal-feature router configuration Can configure later to add protocol and interface changes –Minimal contains inventory of interfaces, opportunity to enter global parameters, opportunity to enter interface parameters, setup script, opportunity to accept configuration »Whey you answer YES, it becomes running configuration »Configure allows you to enter additional commands

3. Initial Setup Each interface must be configures with an IP address and a mask –Set static routes Point-to-point Stub networks –Set Default routes No router table entry for destination network –Set Dynamic routes Router learns paths by receiving period updates from other routers

4. IP Route Command Requires –Networkdestination network –Masksubnet mask –AddressIP address of next-hop router –Interfacename of interface to use to get to destination network –DistanceAdministrative distance – value to help determine best path- low is good (trustworthiness 0-255)

5. Using IP Route Command IP route 172.11.1.0 255.255.255.0 172.11.2.1 –Specifies static route to subnet –Subnet mask in effect –IP address of next-hop router in path to destination LAB –Configure a static route between neighboring routers

6. Default Network Router (config)# ip default-network 172.22.22.1 –Configures default network Requires additional command –Redistribute static S0 all networks have knowledge of the candidate default network

7. Sample Commands Router (config)# router rip Router (config)# network 145.45.3.0 Router (config)# network 191.23.21.0 Router (config)# default-network 154.44.1.0

8. Autonomous System A routing protocol such as Cisco's IGRP requires that you specify this unique, assigned autonomous system number in your configuration. The Network Information Center (NIC) assigns a unique autonomous system to enterprises.

9. Autonomous Systems Interior Routing Protocols –Used within autonomous system RIP, IGRP, EIGRP, OSPF Exterior Routing Protocols –Used between autonomous systems BGP (Border Gateway Protocol) EGP (Exterior Gateway Protocol)

10. Global Configuration Select routing protocol (s) Specify network (s) –Router(config)# router rip An option could be autonomous number –Router(config-router)# 172.34.3.0 Specifies a directly connected router Interface Configuration –Verify address/subnet mask

11. RIP Specified in RFC 1058 –Distance vector –Hop count is metric –Max is 15; over 15 will discard packet –Routing updates broadcast every 30 seconds In RIP all subnet masks must be the same. RIP does not share subnetting information in routing updates.

12. Show IP Protocol Displays values, about routing timers and network information, that are associated with the entire router –Shows protocol, how often updated, next update due time, hold down, routing for all networks, gateways, distances and last update –Administrative distance – default 120

13. Show IP Route Lets you examine the contents of the routing table Essential (for troubleshooting why the router may be dropping or incorrectly routing packets Contains entries for all known networks and subnetworks with a code that shows how information was learned

14. IGRP Distance-vector router protocol – Cisco Sends updates every 90 seconds –Handles indefinite, complex topologies –Flexible for different bandwidth & delay –Scalable for functioning in large networks –Composite metric Bandwidth, delay, load, reliability Speed is primary consideration

15. Enable IGRP Router (config) # router igrp autonomous- system Selects IGRP as routing protocol Router (config-router)# network network # Identifies connected network Like RIP, all subnet masks must be the same – does not share subnetting information in routing updates

16. Sample Commands Router (config) # router igrp 109 –Selects igrp as routing protocol for network 109 Router (config-router)# network 1.0.0.0 –Specifies directly connected networks

17. Show IP Protocol Router # show ip protocol –Identifies protocol –Show algorithm used to calculate metric –Shows update period and next due update –Shows hold down period –Shows networks routed –Shows routing information source

18. Show ip interface Router > show ip interface Displays status and global parameters associated with all IP interfaces Cisco IOS enters route in routing table if interface can send and receive – marked up Unusable interfaces are removed from table

19. Display from show ip interface Internet Address and subnet mask & broadcast address Access lists if any Security level Split horizon (enabled) or not Other features enables or disabled

20. Show IP Route Examine contents of routing table Troubleshoot why packets are dropped or incorrectly routed Tables contains all known networks and subnets and metrics Shows how information was learned Shows if network is connected

21. Debug ip rip Powerful but bandwidth intensive Allow real time examination of routing updates Displays routing updates as they are sent and received Can decrease network performance and cause loss or connectivity – use only during times of low network usage No debug ip rip No debug all

22. Lab Use Cisco commands learned to date –Loops Hold-down timers, max hop count, counting to infinity, poison reserve and split horizon –DCE connection –Interfaces Configure entire 5-router network Troubleshoot problems